main
History Download
Ray Publish 0.1.0 aa1902d

UC2854BDW

Texas Instruments · AC-DC Controllers & Regulators · SOIC-16-300mil

UC2854BDW from Texas Instruments, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground reference for the device; all bypass and timing capacitors should return to GND with leads as short and direct as possible, and all voltages are measured with respect to GND.
2 PKLMT input Peak limit input whose threshold is 0.0 V, connected to the negative voltage on the current sense resistor, with a resistor to REF used to offset the negative sense signal up to GND.
3 CAO output Output of the wide bandwidth current amplifier that commands the PWM to force the correct input current, and it can swing from 0.1 V to 7.5 V.
4 ISENSE input Inverting input of the switch current amplifier that remains functional down to and below GND, and should not be taken below -0.5 V because it is diode-protected to GND.
5 MOUT bidirectional Multiplier output and non-inverting current amplifier input that is a high-impedance current node, which should not be taken below -0.5 V and should satisfy IMOUT ≤ 2 × IAC.
6 IAC input Current input to the analog multiplier proportional to the instantaneous line voltage, where the maximum current at high line should be limited to 250 µA for best performance.
7 VAO input Voltage amplifier output that forms the third input to the multiplier and is internally clamped to 6.0 V.
8 VRMS input Input providing the RMS line voltage to the multiplier, with a linear operating range of 0 V to 5.5 V and an external divider that should produce 1.5 V at low line (85 VAC).
9 VREF power_out Internal reference output used to set the peak limit point and for various device functions, which must be present for the device to operate.
10 ENA input Enable input where a nominal voltage above 2.65 V allows operation to begin and the device shuts off below 2.15 V nominal, with the pin internally clamped to approximately 10 V.
11 VSENSE input Feedback input from the output that feeds the voltage error amplifier, whose output is another input to the multiplier.
12 RSET input Resistor from RSET to ground that programs the oscillator charging current, and on this device it has no effect on clamping the maximum multiplier output current.
13 SS input Soft-start pin held at GND while the device is disabled or VCC is too low, which pulls up to over 3 V through an internal 14 µA source when VCC is valid and the device is enabled.
14 CT input Capacitor from CT to GND that sets the PWM oscillator frequency.
15 VCC power_in Positive supply rail for the device, with an absolute maximum supply voltage of 22 V.
16 GTDRV output PWM output as a 1.5-A peak totem-pole MOSFET gate driver, which should use a series gate resistor of at least 5 Ω to prevent gate impedance interaction and excessive overshoot.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-16-300mil
Category Power Supply Chip
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage (VCC) VCC 22 V 2
GTDRV output current, continuous IGTDRV 0.5 A Continuous 2
GTDRV output current, 50% duty cycle IGTDRV 1.5 A 50% duty cycle 2
Input voltage, VSENSE, VRMS, ISENSE, MOUT 11 V 2
Input voltage, PKLMT 5 V 2
Input current, RSET, IAC, PKLMT, ENA 10 mA 2
Power dissipation 1 W 2
Junction temperature TJ -55 150 °C 2
Storage temperature Tstg -65 150 °C 2
Lead temperature Tsol 300 °C 1,6 mm (1/16 inch) from case for 10 seconds 2
Supply voltage VCC 10 20 V 3
Operating junction temperature, UC2854X TJ -40 85 °C UC2854X (UC2854B) 3
Junction-to-ambient thermal resistance, SOP-16 (DW) θJA 50 130 °C/W Mounted to 5 in² FR4 PCB, 1 oz copper; lower value for 5 in² aluminum PCB 3
Junction-to-case thermal resistance, SOP-16 (DW) θJC 27 °C/W 3
Supply current, off 250 400 µA CAO = 0 V, VAO = 0 V, VCC = VUVLO-0.3 V 4
Supply current, on 12 18 mA 4
VCC turn-on threshold voltage (UCx854B) 8 10.5 11.2 V 4
VCC turn-off threshold voltage (UCx854B) 7.8 10.3 11 V 4
VCC hysteresis (UCx854B) 0.1 0.22 0.5 V 4
VCC clamp voltage 18 20 22 V IVCC = IVCC(on) + 5 mA 4
Input voltage (voltage amplifier) 2.9 3 3.1 V 4
VSENSE bias current -500 -25 500 nA 4
Open loop gain (voltage amplifier) 70 100 dB 2 V ≤ VOUT ≤ 5 V 4
Low-level output voltage (voltage amplifier) VOL 0.3 0.5 V ILOAD = 500 µA 4
Output short-circuit current (voltage amplifier) ISC 1.5 3.5 mA VOUT = 0 V 4
Input offset voltage -4 0 mV VCM = 0 V, TA = 25°C 4
Input offset voltage (overtemperature) -5.5 0 mV VCM = 0 V, Overtemperature 4
ISENSE input bias current -500 500 nA VCM = 0 V 4
Open loop gain (current amplifier) 80 110 dB 2 V ≤ VOUT = 6 V 4
Low-level output voltage (current amplifier) VOL 0.3 0.5 V ILOAD = 500 µA 4
Output short-circuit current (current amplifier) ISC 1.5 3.5 mA VOUT = 0 V 4
Common mode rejection range CMRR -0.3 5 V 4
Gain bandwidth product (current amplifier) fIN 3 5 MHz IN = 100 kHz, 10 mVp-p 4
Reference output voltage VREF 7.4 7.5 7.6 V IREF = 0 mA, TA = 25°C 4
Reference output voltage (over temperature) VREF 7.35 7.5 7.65 V IREF = 0 mA 4
Reference load regulation 0 8 20 mV 1 mA ≤ IREF ≤ 10 mA 4
Reference line regulation 0 14 25 mV 12 V ≤ VCC ≤ 18 V 4
Reference short circuit current ISC 25 35 60 mA VREF = 0 V 4
Oscillator initial accuracy 85 100 115 kHz TA = 25°C 5
Oscillator total variation 80 120 kHz Line, temperature 5
Ramp amplitude (peak-to-peak) 4.9 5.9 5.9 V 5
Ramp valley voltage 0.8 1.3 1.3 V 5
Enable threshold voltage 2.35 2.55 2.8 V 5
Enable hysteresis 500 600 600 mV VFAULT = 2.5 V 5
Enable input bias current -5 -2 -2 µA VENA = 0 V 5
Soft-start charge current 10 14 24 µA VSS = 2.5 V 5
Peak limit offset voltage -15 15 mV 5
Peak limit offset current -200 -100 -100 µA VPKLMIT = -0.1 V 5
Output current, IA limited -220 -200 -170 µA IAC = 100 µA, VRMS = 1 V, RSET = 10 kΩ 5
Output current, zero -2 -0.2 2 µA IAC = 0 µA, RSET = 10 kΩ 5
Output current, power limited -230 -200 -170 µA VRMS = 1.5 V, Va = 6 V 5
Multiplier gain constant K -1.1 -1 -0.9 A/A VRMS = 1.5 V, Va = 6 V, TA = 25°C 5
Gate driver high-level output voltage VOH 12 12.8 V IOUT = -200 mA, VCC = 15 V 5
Gate driver low-level output voltage VOL 1 2.2 V IOUT = 200 mA 5
Gate driver low-level output voltage (10 mA) VOL 300 500 mV IOUT = 10 mA 5
Low-level UVLO voltage 0.9 1.5 V IOUT = 50 mA, VCC = 0 V 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 14,400 square mils use the following values, dual-in-line, 11°C/W; flat pack and pin grid array, 10°C/W.are at the end of each trace. (2) θJA (junction-to-ambient) applies to devices mounted to five s 3

CAD (KiCad official)

  • Symbol: UC2854BDW
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: uc2854bdw-etched.step / uc2854bdw-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); uc2854bdw.step / uc2854bdw.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (29 pp, sha256 20dbe220bdb2dfe8, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF