component
UC2625DWTR
Public Made by Adomby adom
Texas Instruments Brushless DC (BLDC) Motor Driver, SOIC-28-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
page.json+26−23@@ -38,61 +38,61 @@ "number": "1", "name": "E/A OUT", "type": "output",- "description": "Error amplifier output; output swing range 0.25 V to 3.50 V; pull-up current -16 to -5 \u03bcA; drives PWM comparator and may be tied to E/A IN(\u2212) for closed-loop compensation."+ "description": "Error amplifier output; output swing range 0.25 V to 3.50 V; pull-up current -16 to -5 μA; drives PWM comparator and may be tied to E/A IN(−) for closed-loop compensation." }, { "number": "2", "name": "VREF", "type": "power_out",- "description": "Trimmed 5.0 V reference output (4.7-5.3 V over operating range); maximum advised load 30 mA; short-circuit current 50-150 mA; must be bypassed with at least 0.1 \u03bcF to GND."+ "description": "Trimmed 5.0 V reference output (4.7-5.3 V over operating range); maximum advised load 30 mA; short-circuit current 50-150 mA; must be bypassed with at least 0.1 μF to GND." }, { "number": "3", "name": "ISENSE", "type": "output",- "description": "Current-sense amplifier output; ISENSE = 2.5 V + 2 \u00d7 |ISENSE1 \u2212 ISENSE2|; level shift 2.4-2.65 V; feeds peak-current (0.14-0.26 V) and overcurrent (0.26-0.36 V) comparators."+ "description": "Current-sense amplifier output; ISENSE = 2.5 V + 2 × |ISENSE1 − ISENSE2|; level shift 2.4-2.65 V; feeds peak-current (0.14-0.26 V) and overcurrent (0.26-0.36 V) comparators." }, { "number": "4", "name": "ISENSE1", "type": "input",- "description": "Differential current-sense input 1; input range \u22121 V to +2 V; input bias current -850 to 0 \u03bcA to 0 V; offset current \u00b112 \u03bcA max; use matched filter resistors \u22642 k\u03a9 for accuracy."+ "description": "Differential current-sense input 1; input range −1 V to +2 V; input bias current -850 to 0 μA to 0 V; offset current ±12 μA max; use matched filter resistors ≤2 kΩ for accuracy." }, { "number": "5", "name": "ISENSE2", "type": "input",- "description": "Differential current-sense input 2; interchangeable with ISENSE1; input range \u22121 V to +2 V; input bias current -850 to 0 \u03bcA; differential input may be as high as \u00b10.5 V before saturation."+ "description": "Differential current-sense input 2; interchangeable with ISENSE1; input range −1 V to +2 V; input bias current -850 to 0 μA; differential input may be as high as ±0.5 V before saturation." }, { "number": "6", "name": "DIR", "type": "input",- "description": "Motor direction latch input; threshold 0.8-2.0 V, hysteresis 0.6 V; input current -30 to 30 \u03bcA; direction change is inhibited when SPEED-IN exceeds 250 mV to prevent unsafe reversal."+ "description": "Motor direction latch input; threshold 0.8-2.0 V, hysteresis 0.6 V; input current -30 to 30 μA; direction change is inhibited when SPEED-IN exceeds 250 mV to prevent unsafe reversal." }, { "number": "7", "name": "SPEED-IN", "type": "input",- "description": "Speed-sense input used to gate the direction latch; threshold 220-290 mV (typ 257 mV); input current -30 to 30 \u03bcA; typically connected to TACH-OUT through an RC filter."+ "description": "Speed-sense input used to gate the direction latch; threshold 220-290 mV (typ 257 mV); input current -30 to 30 μA; typically connected to TACH-OUT through an RC filter." }, { "number": "8", "name": "H1", "type": "input",- "description": "Hall-effect shaft-position sensor input 1; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 \u03bcA over operating range."+ "description": "Hall-effect shaft-position sensor input 1; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range." }, { "number": "9", "name": "H2", "type": "input",- "description": "Hall-effect shaft-position sensor input 2; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 \u03bcA over operating range."+ "description": "Hall-effect shaft-position sensor input 2; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range." }, { "number": "10", "name": "H3", "type": "input",- "description": "Hall-effect shaft-position sensor input 3; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 \u03bcA over operating range."+ "description": "Hall-effect shaft-position sensor input 3; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range." }, { "number": "11",@@ -128,49 +128,49 @@ "number": "16", "name": "PUC", "type": "output",- "description": "High-side open-collector driver C; active low commands a high-side device on; rated to 50 V; leakage \u226425 \u03bcA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA."+ "description": "High-side open-collector driver C; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA." }, { "number": "17", "name": "PUB", "type": "output",- "description": "High-side open-collector driver B; active low commands a high-side device on; rated to 50 V; leakage \u226425 \u03bcA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA."+ "description": "High-side open-collector driver B; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA." }, { "number": "18", "name": "PUA", "type": "output",- "description": "High-side open-collector driver A; active low commands a high-side device on; rated to 50 V; leakage \u226425 \u03bcA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA."+ "description": "High-side open-collector driver A; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA." }, { "number": "19", "name": "VCC", "type": "power_in",- "description": "Main logic and control supply; operating range 10 V to 18 V; under-voltage lockout keeps all outputs off below 7.5 V; turn-on threshold 8.65-9.45 V; bypass with 0.1 \u03bcF ceramic."+ "description": "Main logic and control supply; operating range 10 V to 18 V; under-voltage lockout keeps all outputs off below 7.5 V; turn-on threshold 8.65-9.45 V; bypass with 0.1 μF ceramic." }, { "number": "20", "name": "TACH-OUT", "type": "output",- "description": "Tachometer output; fires a fixed-width 5 V pulse (on-time 170-280 \u03bcs) on each H1/H2/H3 transition; high level 4.7-5.3 V into 10 k\u03a9; low level \u22640.2 V; average voltage is proportional to speed."+ "description": "Tachometer output; fires a fixed-width 5 V pulse (on-time 170-280 μs) on each H1/H2/H3 transition; high level 4.7-5.3 V into 10 kΩ; low level ≤0.2 V; average voltage is proportional to speed." }, { "number": "21", "name": "RC-BRAKE", "type": "bidirectional",- "description": "RC brake timing and brake-command pin; external RT (10 k\u03a9-500 k\u03a9) and CT (1 nF-100 nF) to GND set discharge window T = 0.67 RTCT; pulling pin below 0.8-1.2 V threshold commands full-brake mode; input current -4.0 to -1.9 mA."+ "description": "RC brake timing and brake-command pin; external RT (10 kΩ-500 kΩ) and CT (1 nF-100 nF) to GND set discharge window T = 0.67 RTCT; pulling pin below 0.8-1.2 V threshold commands full-brake mode; input current -4.0 to -1.9 mA." }, { "number": "22", "name": "QUAD SEL", "type": "input",- "description": "Two/four-quadrant chopping selection input; low selects two-quadrant, high selects four-quadrant; threshold 0.8-2.0 V; hysteresis 70 mV; input current -30 to 150 \u03bcA."+ "description": "Two/four-quadrant chopping selection input; low selects two-quadrant, high selects four-quadrant; threshold 0.8-2.0 V; hysteresis 70 mV; input current -30 to 150 μA." }, { "number": "23", "name": "OV-COAST", "type": "input",- "description": "Over-voltage shutdown and coast input; inhibit threshold 1.65-1.85 V; restart threshold 1.55-1.75 V; hysteresis 0.05-0.15 V; input current -10 to 0 \u03bcA; accepts TTL, 5-V CMOS, or 12-V CMOS."+ "description": "Over-voltage shutdown and coast input; inhibit threshold 1.65-1.85 V; restart threshold 1.55-1.75 V; hysteresis 0.05-0.15 V; input current -10 to 0 μA; accepts TTL, 5-V CMOS, or 12-V CMOS." }, { "number": "24",@@ -182,25 +182,25 @@ "number": "25", "name": "RC-OSC", "type": "passive",- "description": "Oscillator RC timing pin; connect ROSC (10 k\u03a9-100 k\u03a9) to VREF and COSC (1 nF-100 nF) to GND; oscillator frequency F \u2248 2/(ROSC \u00d7 COSC); ramp is \u22481.2 V peak-to-peak centered at 1.6 V; 40-60 kHz typical."+ "description": "Oscillator RC timing pin; connect ROSC (10 kΩ-100 kΩ) to VREF and COSC (1 nF-100 nF) to GND; oscillator frequency F ≈ 2/(ROSC × COSC); ramp is ≈1.2 V peak-to-peak centered at 1.6 V; 40-60 kHz typical." }, { "number": "26", "name": "PWM IN", "type": "input",- "description": "PWM comparator input; compared to E/A OUT to generate the PWM chop command; input current 0-30 \u03bcA; typically connected to the RC-OSC ramp for voltage-mode PWM control."+ "description": "PWM comparator input; compared to E/A OUT to generate the PWM chop command; input current 0-30 μA; typically connected to the RC-OSC ramp for voltage-mode PWM control." }, { "number": "27", "name": "E/A IN(-)", "type": "input",- "description": "Error amplifier inverting input; input current -5 to +5 \u03bcA; common-mode input range 0 V to 3 V; input offset \u00b110 mV; tie to E/A OUT for unity-gain buffer configuration."+ "description": "Error amplifier inverting input; input current -5 to +5 μA; common-mode input range 0 V to 3 V; input offset ±10 mV; tie to E/A OUT for unity-gain buffer configuration." }, { "number": "28", "name": "E/A IN(+)", "type": "input",- "description": "Error amplifier non-inverting input; input current -5 to +5 \u03bcA; common-mode input range 0 V to 3 V; voltage gain 70-90 dB; can be driven by ISENSE output, TACH-OUT filter, or external command voltage."+ "description": "Error amplifier non-inverting input; input current -5 to +5 μA; common-mode input range 0 V to 3 V; voltage gain 70-90 dB; can be driven by ISENSE output, TACH-OUT filter, or external command voltage." } ], "provenance": {@@ -278,5 +278,8 @@ "docs/uc2625dwtr-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }