TX4310B

{
 "schema": "adom.pads/1",
 "slug": "tx4310b",
 "footprint": "SOT-23-6",
 "generated_from": {
  "footprint": "SOT-23-6@sha256:f341c73aac9dcb55",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -1.1375,
   -0.95
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOT-23-6@sha256:f341c73aac9dcb55"
 },
 "pad_count": 6,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "VOUT",
   "type": "power_out",
   "description": "Regulated charge-pump voltage output, nominally 3.3 V ±4% (3.17-3.43 V). Requires a low-ESR (<0.1 Ω) ceramic bypass capacitor of ≥10 µF to GND for stability and low output ripple. Can source up to ~250 mA at VIN=3 V; internally current-limited to ~300 mA under short-circuit.",
   "is_pin1": true,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "GND",
   "type": "power_in",
   "description": "Device ground / power return. Should be tied to a solid ground plane; bypass capacitors on VDD and VOUT should return to this pin with the shortest possible traces to minimize switching noise at the 1.2 MHz pump frequency.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "EN",
   "type": "input",
   "description": "Active-high CMOS enable input with a threshold of ~0.8 V; driving EN low places the part in shutdown (all internal circuitry off, VOUT disconnected from VDD, IQ <1 µA). High-impedance CMOS input - MUST NOT be left floating; always drive with a valid logic level. Absolute-max VEN = -0.3 V to 6 V.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "C-",
   "type": "passive",
   "description": "Negative terminal of the flying (bootstrap) charge-pump capacitor. Connect between C- (pin 4) and C+ (pin 6) a low-ESR ceramic capacitor (≥2.2 µF recommended to achieve rated output current). Never use polar capacitors (tantalum/aluminum) here - the pin voltage can reverse during startup.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "VDD",
   "type": "power_in",
   "description": "Input supply pin, 1.8 V to 5 V operating range (absolute-max 6 V). Requires a low-ESR (<0.1 Ω) ceramic bypass capacitor of ≥10 µF to GND placed close to the pin to minimize input ripple. No-load supply current ~0.65 mA (typ, VIN=2.7 V); shutdown current <1 µA.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "C+",
   "type": "passive",
   "description": "Positive terminal of the flying (bootstrap) charge-pump capacitor. Connect a low-ESR ceramic capacitor (≥2.2 µF) between C+ (pin 6) and C- (pin 4). Do not use tantalum or aluminum electrolytics; polarity across this capacitor can reverse during startup.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}