main
Ray
Publish 0.1.0
bf1cbe1
TUSB8020BIPHPR
Texas Instruments · USB Converters · HTQFP-48(7x7)
TUSB8020BIPHPR from Texas Instruments, in a HTQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | 1.1-V power rail. |
| 2 | SCL/SMBCLK | bidirectional | I2C clock/SMBus clock; serves as the serial clock for an I2C EEPROM when SMBUSz = 1 or for an SMBus host when SMBUSz = 0, and must be pulled up to use the OTP ROM. |
| 3 | SDA/SMBDAT | bidirectional | I2C data/SMBus data; serves as the serial data interface for an I2C EEPROM when SMBUSz = 1 or for an SMBus host when SMBUSz = 0, and must be pulled up to use the OTP ROM. |
| 4 | PWRCTL1/BATEN1 | bidirectional | USB port 1 power-on control for the downstream power switch, with the level sampled at reset to set battery charging support for Port 1 (0 = not supported, 1 = supported). |
| 5 | OVERCUR1z | input | USB downstream port 1 overcurrent detection input, where 0 indicates an overcurrent event has occurred and 1 indicates none has occurred. |
| 6 | PWRCTL2/BATEN2 | bidirectional | Power-on control and battery charging enable for downstream port 2, with the level sampled at reset to set battery charging support for port 2 (0 = not supported, 1 = supported). |
| 7 | VDD33 | power_in | 3.3-V power rail. |
| 8 | OVERCUR2z | input | Overcurrent detection input for downstream port 2, where 0 indicates an overcurrent event has occurred and 1 indicates none has occurred. |
| 9 | USB_VBUS | input | USB upstream port power monitor, which must connect to VBUS through a 90.9-kΩ ±1% resistor and to ground through a 10-kΩ ±1% resistor. |
| 10 | TEST | input | TEST mode enable; asserting it high at reset enables test mode, it is reserved for factory use, and it is recommended to pull it down to ground. |
| 11 | GRSTz | input | Global power reset that returns all internal registers to default states, and the device is completely nonfunctional while it is asserted. |
| 12 | VDD | power_in | 1.1-V power rail. |
| 13 | VDD33 | power_in | 3.3-V power rail. |
| 14 | USB_DP_DN2 | bidirectional | USB high-speed differential transceiver (positive) for downstream port 2. |
| 15 | USB_DM_DN2 | bidirectional | USB high-speed differential transceiver (negative) for downstream port 2. |
| 16 | USB_SSTXP_DN2 | output | USB SuperSpeed transmitter differential pair (positive) for downstream port 2. |
| 17 | USB_SSTXM_DN2 | output | USB SuperSpeed transmitter differential pair (negative) for downstream port 2. |
| 18 | VDD | power_in | 1.1-V power rail. |
| 19 | USB_SSRXP_DN2 | input | USB SuperSpeed receiver differential pair (positive) for downstream port 2. |
| 20 | USB_SSRXM_DN2 | input | USB SuperSpeed receiver differential pair (negative) for downstream port 2. |
| 21 | PWRCTL_POL/SS_DN1 | bidirectional | Power control polarity sampled at reset to set PWRCTL[2:1] polarity (0 = active high, 1 = active low); after reset it indicates the SuperSpeed USB connection status of downstream port 1. |
| 22 | SMBUSz/SS_DN2 | input | SMBus mode select sampled at reset (0 = SMBus mode, 1 = I2C mode); after reset it indicates the SuperSpeed USB connection status of downstream port 2, where 1 means SuperSpeed USB. |
| 23 | VDD33 | power_in | 3.3-V power rail. |
| 24 | USB_R1 | input | Precision resistor reference, where a 9.53-kΩ ±1% resistor should be connected between USB_R1 and GND. |
| 25 | VDD33 | power_in | 3.3-V power rail. |
| 26 | USB_DP_UP | bidirectional | USB high-speed differential transceiver (positive) for the upstream port. |
| 27 | USB_DM_UP | bidirectional | USB high-speed differential transceiver (negative) for the upstream port. |
| 28 | USB_SSTXM_UP | output | USB SuperSpeed transmitter differential pair (negative) for the upstream port. |
| 29 | USB_SSTXP_UP | output | USB SuperSpeed transmitter differential pair (positive) for the upstream port. |
| 30 | VDD | power_in | 1.1-V power rail. |
| 31 | USB_SSRXM_UP | input | USB SuperSpeed receiver differential pair (negative) for the upstream port. |
| 32 | USB_SSRXP_UP | input | USB SuperSpeed receiver differential pair (positive) for the upstream port. |
| 33 | VDD33 | power_in | 3.3-V power rail. |
| 34 | VDD | power_in | 1.1-V power rail. |
| 35 | GANGED/SMBA2/HS_UP | input | Ganged operation enable sampled at reset (0 = individual power control, 1 = ganged); it sets SMBus address bit 2 in SMBus mode, and after reset it indicates high-speed USB connection status of the upstream port. |
| 36 | FULLPWRMGMTz/SMBA1/SS_UP | input | Full power management enable sampled at reset (0 = power switching supported, 1 = not supported); it sets SMBus address bit 1 in SMBus mode, and after reset it indicates SuperSpeed USB connection status of the upstream port. |
| 37 | VDD33 | power_in | 3.3-V power rail. |
| 38 | XI | input | Crystal input for the internal oscillator, which may alternatively be driven by an external oscillator, and a 1-MΩ feedback resistor is required between XI and XO when using a crystal. |
| 39 | XO | output | Crystal output for the internal oscillator, which may be left unconnected if XI is driven by an external oscillator, and a 1-MΩ feedback resistor is required between XI and XO when using a crystal. |
| 40 | VDD33 | power_in | 3.3-V power rail. |
| 41 | USB_DP_DN1 | bidirectional | USB high-speed differential transceiver (positive) for downstream port 1. |
| 42 | USB_DM_DN1 | bidirectional | USB high-speed differential transceiver (negative) for downstream port 1. |
| 43 | USB_SSTXP_DN1 | output | USB SuperSpeed transmitter differential pair (positive) for downstream port 1. |
| 44 | USB_SSTXM_DN1 | output | USB SuperSpeed transmitter differential pair (negative) for downstream port 1. |
| 45 | VDD | power_in | 1.1-V power rail. |
| 46 | USB_SSRXP_DN1 | input | USB SuperSpeed receiver differential pair (positive) for downstream port 1. |
| 47 | USB_SSRXM_DN1 | input | USB SuperSpeed receiver differential pair (negative) for downstream port 1. |
| 48 | VDD33 | power_in | 3.3-V power rail. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTQFP-48(7x7) |
| Category | Interface |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDD steady-state | VDD | -0.3 | 1.4 | V | 6 | ||
| Supply voltage VDD33 steady-state | VDD33 | -0.3 | 3.8 | V | 6 | ||
| Voltage range USB_SSRXP_UP, USB_SSRXN_UP, USB_SSRXP_DN[4:1], USB_SSRXN_DP[4:1] and USB_VBUS terminals | -0.3 | 1.4 | V | 6 | |||
| Voltage range XI terminals | -0.3 | 2.45 | V | 6 | |||
| Voltage range all other terminals | -0.3 | 3.8 | V | 6 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 6 | ||
| ESD human body model (HBM) | V(ESD) | -2000 | 2000 | V | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins | 6 | |
| ESD charged device model (CDM) | V(ESD) | -500 | 500 | V | Charged device model (CDM), per JEDEC specification JESD22-C101, all pins | 6 | |
| 1.1-V supply voltage | VDD | 0.99 | 1.1 | 1.26 | V | 6 | |
| 3.3-V supply voltage | VDD33 | 3 | 3.3 | 3.6 | V | 6 | |
| Voltage at USB_VBUS pad | USB_VBUS | 0 | 1.155 | V | 6 | ||
| Operating free-air temperature range (TUSB8020BI) | TA | -40 | 25 | 85 | °C | TUSB8020BI | 6 |
| Operating junction temperature range | TJ | -40 | 25 | 105 | °C | 6 | |
| High-level input voltage | VIH | 2 | V | VDD33 | 7 | ||
| Low-level input voltage | VIL | 0 | 0.8 | V | VDD33 | 7 | |
| Input voltage | VI | 0 | V | VDD33 | 7 | ||
| Output voltage | VO | 0 | V | 7 | |||
| Input transition time (trise and tfall) | tt | 25 | ns | 7 | |||
| High-level output voltage | VOH | 2.4 | V | VDD33, IOH = -4 mA | 7 | ||
| Low-level output voltage | VOL | 0.4 | V | VDD33, IOL = 4 mA | 7 | ||
| High-impedance output current | IOZ | -20 | 20 | µA | VDD33, VI = 0 to VDD33 | 7 | |
| High-impedance output current with internal pullup or pulldown resistor | IOZP | -225 | 225 | µA | VDD33, VI = 0 to VDD33 | 7 | |
| Input current | II | -15 | 15 | µA | VDD33, VI = 0 to VDD33 | 7 | |
| VDD33 stable before VDD stable. No timing relationship between VDD33 and VDD | td1 | 0 | ms | 7 | |||
| VDD and VDD33 stable before deassertion of GRSTZ | td2 | 3 | ms | 7 | |||
| Setup for MISC inputs sampled at the deassertion of GRSTZ | tsu_io | 0.1 | µs | 7 | |||
| Hold for MISC inputs sampled at the deassertion of GRSTZ | thd_io | 0.1 | µs | 7 | |||
| VDD33 supply ramp requirements | tVDD33_RAMP | 0.2 | 100 | ms | 7 | ||
| VDD supply ramp requirements | tVDD_RAMP | 0.2 | 100 | ms | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 31.8 | °C/W | 48 pins, PHP package | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 16.1 | °C/W | 48 pins, PHP package | 6 | ||
| Junction-to-board thermal resistance | RθJB | 13 | °C/W | 48 pins, PHP package | 6 | ||
| Junction-to-top characterization parameter | ψJT | 0.5 | °C/W | 48 pins, PHP package | 6 | ||
| Junction-to-board characterization parameter | ψJB | 12.9 | °C/W | 48 pins, PHP package | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 0.9 | °C/W | 48 pins, PHP package | 6 |
CAD (Adom-generated)
- Symbol:
TUSB8020BIPHPR - Footprint:
Adom_Gen:Texas_Instruments_TUSB8020_91920e - 3D model: generated to fit the land (STEP)
- 3D model files:
tusb8020biphpr-etched.step/tusb8020biphpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tusb8020biphpr.step/tusb8020biphpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (44 pp, sha256
1333853b6181ec99, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
# TUSB8020BIPHPR
**Texas Instruments** · USB Converters · HTQFP-48(7x7)
TUSB8020BIPHPR from Texas Instruments, in a HTQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | 1.1-V power rail. |
| 2 | SCL/SMBCLK | bidirectional | I2C clock/SMBus clock; serves as the serial clock for an I2C EEPROM when SMBUSz = 1 or for an SMBus host when SMBUSz = 0, and must be pulled up to use the OTP ROM. |
| 3 | SDA/SMBDAT | bidirectional | I2C data/SMBus data; serves as the serial data interface for an I2C EEPROM when SMBUSz = 1 or for an SMBus host when SMBUSz = 0, and must be pulled up to use the OTP ROM. |
| 4 | PWRCTL1/BATEN1 | bidirectional | USB port 1 power-on control for the downstream power switch, with the level sampled at reset to set battery charging support for Port 1 (0 = not supported, 1 = supported). |
| 5 | OVERCUR1z | input | USB downstream port 1 overcurrent detection input, where 0 indicates an overcurrent event has occurred and 1 indicates none has occurred. |
| 6 | PWRCTL2/BATEN2 | bidirectional | Power-on control and battery charging enable for downstream port 2, with the level sampled at reset to set battery charging support for port 2 (0 = not supported, 1 = supported). |
| 7 | VDD33 | power_in | 3.3-V power rail. |
| 8 | OVERCUR2z | input | Overcurrent detection input for downstream port 2, where 0 indicates an overcurrent event has occurred and 1 indicates none has occurred. |
| 9 | USB_VBUS | input | USB upstream port power monitor, which must connect to VBUS through a 90.9-kΩ ±1% resistor and to ground through a 10-kΩ ±1% resistor. |
| 10 | TEST | input | TEST mode enable; asserting it high at reset enables test mode, it is reserved for factory use, and it is recommended to pull it down to ground. |
| 11 | GRSTz | input | Global power reset that returns all internal registers to default states, and the device is completely nonfunctional while it is asserted. |
| 12 | VDD | power_in | 1.1-V power rail. |
| 13 | VDD33 | power_in | 3.3-V power rail. |
| 14 | USB_DP_DN2 | bidirectional | USB high-speed differential transceiver (positive) for downstream port 2. |
| 15 | USB_DM_DN2 | bidirectional | USB high-speed differential transceiver (negative) for downstream port 2. |
| 16 | USB_SSTXP_DN2 | output | USB SuperSpeed transmitter differential pair (positive) for downstream port 2. |
| 17 | USB_SSTXM_DN2 | output | USB SuperSpeed transmitter differential pair (negative) for downstream port 2. |
| 18 | VDD | power_in | 1.1-V power rail. |
| 19 | USB_SSRXP_DN2 | input | USB SuperSpeed receiver differential pair (positive) for downstream port 2. |
| 20 | USB_SSRXM_DN2 | input | USB SuperSpeed receiver differential pair (negative) for downstream port 2. |
| 21 | PWRCTL_POL/SS_DN1 | bidirectional | Power control polarity sampled at reset to set PWRCTL[2:1] polarity (0 = active high, 1 = active low); after reset it indicates the SuperSpeed USB connection status of downstream port 1. |
| 22 | SMBUSz/SS_DN2 | input | SMBus mode select sampled at reset (0 = SMBus mode, 1 = I2C mode); after reset it indicates the SuperSpeed USB connection status of downstream port 2, where 1 means SuperSpeed USB. |
| 23 | VDD33 | power_in | 3.3-V power rail. |
| 24 | USB_R1 | input | Precision resistor reference, where a 9.53-kΩ ±1% resistor should be connected between USB_R1 and GND. |
| 25 | VDD33 | power_in | 3.3-V power rail. |
| 26 | USB_DP_UP | bidirectional | USB high-speed differential transceiver (positive) for the upstream port. |
| 27 | USB_DM_UP | bidirectional | USB high-speed differential transceiver (negative) for the upstream port. |
| 28 | USB_SSTXM_UP | output | USB SuperSpeed transmitter differential pair (negative) for the upstream port. |
| 29 | USB_SSTXP_UP | output | USB SuperSpeed transmitter differential pair (positive) for the upstream port. |
| 30 | VDD | power_in | 1.1-V power rail. |
| 31 | USB_SSRXM_UP | input | USB SuperSpeed receiver differential pair (negative) for the upstream port. |
| 32 | USB_SSRXP_UP | input | USB SuperSpeed receiver differential pair (positive) for the upstream port. |
| 33 | VDD33 | power_in | 3.3-V power rail. |
| 34 | VDD | power_in | 1.1-V power rail. |
| 35 | GANGED/SMBA2/HS_UP | input | Ganged operation enable sampled at reset (0 = individual power control, 1 = ganged); it sets SMBus address bit 2 in SMBus mode, and after reset it indicates high-speed USB connection status of the upstream port. |
| 36 | FULLPWRMGMTz/SMBA1/SS_UP | input | Full power management enable sampled at reset (0 = power switching supported, 1 = not supported); it sets SMBus address bit 1 in SMBus mode, and after reset it indicates SuperSpeed USB connection status of the upstream port. |
| 37 | VDD33 | power_in | 3.3-V power rail. |
| 38 | XI | input | Crystal input for the internal oscillator, which may alternatively be driven by an external oscillator, and a 1-MΩ feedback resistor is required between XI and XO when using a crystal. |
| 39 | XO | output | Crystal output for the internal oscillator, which may be left unconnected if XI is driven by an external oscillator, and a 1-MΩ feedback resistor is required between XI and XO when using a crystal. |
| 40 | VDD33 | power_in | 3.3-V power rail. |
| 41 | USB_DP_DN1 | bidirectional | USB high-speed differential transceiver (positive) for downstream port 1. |
| 42 | USB_DM_DN1 | bidirectional | USB high-speed differential transceiver (negative) for downstream port 1. |
| 43 | USB_SSTXP_DN1 | output | USB SuperSpeed transmitter differential pair (positive) for downstream port 1. |
| 44 | USB_SSTXM_DN1 | output | USB SuperSpeed transmitter differential pair (negative) for downstream port 1. |
| 45 | VDD | power_in | 1.1-V power rail. |
| 46 | USB_SSRXP_DN1 | input | USB SuperSpeed receiver differential pair (positive) for downstream port 1. |
| 47 | USB_SSRXM_DN1 | input | USB SuperSpeed receiver differential pair (negative) for downstream port 1. |
| 48 | VDD33 | power_in | 3.3-V power rail. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTQFP-48(7x7) |
| Category | Interface |
| Pins | 49 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDD steady-state | VDD | -0.3 | | 1.4 | V | | 6 |
| Supply voltage VDD33 steady-state | VDD33 | -0.3 | | 3.8 | V | | 6 |
| Voltage range USB_SSRXP_UP, USB_SSRXN_UP, USB_SSRXP_DN[4:1], USB_SSRXN_DP[4:1] and USB_VBUS terminals | | -0.3 | | 1.4 | V | | 6 |
| Voltage range XI terminals | | -0.3 | | 2.45 | V | | 6 |
| Voltage range all other terminals | | -0.3 | | 3.8 | V | | 6 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 6 |
| ESD human body model (HBM) | V(ESD) | -2000 | | 2000 | V | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins | 6 |
| ESD charged device model (CDM) | V(ESD) | -500 | | 500 | V | Charged device model (CDM), per JEDEC specification JESD22-C101, all pins | 6 |
| 1.1-V supply voltage | VDD | 0.99 | 1.1 | 1.26 | V | | 6 |
| 3.3-V supply voltage | VDD33 | 3 | 3.3 | 3.6 | V | | 6 |
| Voltage at USB_VBUS pad | USB_VBUS | 0 | | 1.155 | V | | 6 |
| Operating free-air temperature range (TUSB8020BI) | TA | -40 | 25 | 85 | °C | TUSB8020BI | 6 |
| Operating junction temperature range | TJ | -40 | 25 | 105 | °C | | 6 |
| High-level input voltage | VIH | 2 | | | V | VDD33 | 7 |
| Low-level input voltage | VIL | 0 | | 0.8 | V | VDD33 | 7 |
| Input voltage | VI | 0 | | | V | VDD33 | 7 |
| Output voltage | VO | 0 | | | V | | 7 |
| Input transition time (trise and tfall) | tt | | | 25 | ns | | 7 |
| High-level output voltage | VOH | 2.4 | | | V | VDD33, IOH = -4 mA | 7 |
| Low-level output voltage | VOL | | | 0.4 | V | VDD33, IOL = 4 mA | 7 |
| High-impedance output current | IOZ | -20 | | 20 | µA | VDD33, VI = 0 to VDD33 | 7 |
| High-impedance output current with internal pullup or pulldown resistor | IOZP | -225 | | 225 | µA | VDD33, VI = 0 to VDD33 | 7 |
| Input current | II | -15 | | 15 | µA | VDD33, VI = 0 to VDD33 | 7 |
| VDD33 stable before VDD stable. No timing relationship between VDD33 and VDD | td1 | 0 | | | ms | | 7 |
| VDD and VDD33 stable before deassertion of GRSTZ | td2 | 3 | | | ms | | 7 |
| Setup for MISC inputs sampled at the deassertion of GRSTZ | tsu_io | 0.1 | | | µs | | 7 |
| Hold for MISC inputs sampled at the deassertion of GRSTZ | thd_io | 0.1 | | | µs | | 7 |
| VDD33 supply ramp requirements | tVDD33_RAMP | 0.2 | | 100 | ms | | 7 |
| VDD supply ramp requirements | tVDD_RAMP | 0.2 | | 100 | ms | | 7 |
| Junction-to-ambient thermal resistance | RθJA | | 31.8 | | °C/W | 48 pins, PHP package | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 16.1 | | °C/W | 48 pins, PHP package | 6 |
| Junction-to-board thermal resistance | RθJB | | 13 | | °C/W | 48 pins, PHP package | 6 |
| Junction-to-top characterization parameter | ψJT | | 0.5 | | °C/W | 48 pins, PHP package | 6 |
| Junction-to-board characterization parameter | ψJB | | 12.9 | | °C/W | 48 pins, PHP package | 6 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 0.9 | | °C/W | 48 pins, PHP package | 6 |
## CAD (Adom-generated)
- Symbol: `TUSB8020BIPHPR`
- Footprint: `Adom_Gen:Texas_Instruments_TUSB8020_91920e`
- 3D model: generated to fit the land (STEP)
- 3D model files: `tusb8020biphpr-etched.step` / `tusb8020biphpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tusb8020biphpr.step` / `tusb8020biphpr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tusb8020b.pdf) (44 pp, sha256 `1333853b6181ec99`, retrieved 2026-11-17, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
[Datasheet PDF](docs/tusb8020biphpr-datasheet.pdf)