3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTSC2046IPW
Texas Instruments · Touch Screen Controllers · TSSOP-16
TSC2046IPW from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | +VCC | power_in | Analog supply, specified at 2.7V to 3.6V with an operating range of 2.2V to 5.25V, and must be greater than or equal to IOVDD. |
| 2 | X+ | passive | X+ touch-panel connection to the position ADC input and driver switch, with an on-resistance of 5 Ω. |
| 3 | Y+ | passive | Y+ touch-panel connection to the position ADC input and driver switch, with an on-resistance of 5 Ω. |
| 4 | X− | passive | X− touch-panel connection to the position ADC input and driver switch, with an on-resistance of 6 Ω. |
| 5 | Y− | passive | Y− touch-panel connection to the position ADC input and driver switch, with an on-resistance of 6 Ω. |
| 6 | GND | power_in | Ground reference for the device, which should be connected to a clean ground point. |
| 7 | VBAT | power_in | Battery monitor input for 0V to 6V, divided by 4 before the ADC so that a 5.5V battery reads 1.375V. |
| 8 | AUX | passive | Auxiliary single-ended analog input to the ADC, with an absolute input range of −0.2V to +VCC + 0.2V. |
| 9 | VREF | power_in | Reference input/output: the internal 2.5V reference (2.45V to 2.55V) is available here, or an external reference from 1.0V to +VCC can be applied. |
| 10 | IOVDD | power_in | Digital I/O supply operating from 1.5V to +VCC, and must not exceed +VCC. |
| 11 | PENIRQ | output | Pen-interrupt output with a nominal 50 kΩ internal pull-up (90 kΩ on the −90 version) that goes low when the screen is touched. |
| 12 | DOUT | tri_state | Serial data output shifted on the falling edge of DCLK, and high impedance when CS is high. |
| 13 | BUSY | tri_state | Busy output that is high impedance when CS is high. |
| 14 | DIN | input | Serial data input latched on the rising edge of DCLK while CS is low; the device ignores DIN until the start bit is detected. |
| 15 | CS | input | Chip select input that enables the serial I/O register, with CS high placing the ADC in power-down mode. |
| 16 | DCLK | input | External clock input that runs the SAR conversion process and synchronizes serial data I/O. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-16 |
| Category | Data Acquisition |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| +VCC and IOVDD to GND | -0.3 | 6 | V | 2 | |||
| Analog Inputs to GND | -0.3 | V | max printed as +VCC + 0.3V (formula, not numeric) | 2 | |||
| Digital Inputs to GND | -0.3 | V | max printed as IOVDD + 0.3V (formula, not numeric) | 2 | |||
| Power Dissipation | 250 | mW | 2 | ||||
| Maximum Junction Temperature | 150 | °C | 2 | ||||
| Operating Temperature Range | -40 | 85 | °C | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (soldering, 10s) | 300 | °C | soldering, 10s | 2 | |||
| Full-Scale Input Span | 0 | V | Positive Input−Negative Input; max printed as VREF (formula) | 3 | |||
| Absolute Input Range, Positive Input | -0.2 | V | Positive Input; max printed as +VCC + 0.2 (formula) | 3 | |||
| Absolute Input Range, Negative Input | -0.2 | 0.2 | V | Negative Input | 3 | ||
| Integral Linearity Error | -2 | 2 | LSB | 3 | |||
| Offset Error | -6 | 6 | LSB | 3 | |||
| Gain Error | -4 | 4 | LSB | External VREF | 3 | ||
| Internal Reference Voltage | 2.45 | 2.5 | 2.55 | V | 3 | ||
| Reference Input Range | 1 | V | 3 | ||||
| Battery Monitor Input Voltage Range | 0.5 | 6 | V | 3 | |||
| Battery Monitor Accuracy | -2 | 2 | % | VBAT = 0.5V to 5.5V, External VREF = 2.5V | 3 | ||
| Battery Monitor Accuracy | -3 | 3 | % | VBAT = 0.5V to 5.5V, Internal Reference | 3 | ||
| Temperature Measurement Range | -40 | 85 | °C | 3 | |||
| Temperature Accuracy, Differential Method | -2 | 2 | °C | Differential Method | 3 | ||
| Temperature Accuracy, TEMP0 | -3 | 3 | °C | TEMP0 | 3 | ||
| Digital Input Low Voltage | VIL | -0.3 | V | /IIL/ ≤ +5µA; max printed as 0.3 • IOVDD (formula) | 4 | ||
| +VCC Specified Performance | +VCC | 2.7 | 3.6 | V | 4 | ||
| +VCC Operating Range | +VCC | 2.2 | 5.25 | V | 4 | ||
| IOVDD Supply Range | IOVDD | 1.5 | V | max printed as +VCC (formula) | 4 | ||
| Quiescent Current | 280 | 650 | µA | Internal Reference Off | 4 | ||
| Temperature Range, Specified Performance | -40 | 85 | °C | 4 | |||
| PENIRQ Internal Pull-up Resistor | 36 | 50 | 67 | kΩ | Standard version (not -90); process and temperature variation | 16 |
CAD (KiCad official)
- Symbol:
TSC2046IPW - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
tsc2046ipw-etched.step/tsc2046ipw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tsc2046ipw.step/tsc2046ipw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (34 pp, sha256
88219477cf1d73ae, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).