main
History Download
Ray Publish 0.1.0 b9b2b7b

TRS3243CDBR

Texas Instruments · RS232 ICs · SSOP-28-208mil

TRS3243CDBR from Texas Instruments, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 C2+ passive Positive terminal of the voltage-doubler charge-pump capacitor (C2), which the datasheet specifies as 0.1 µF at VCC = 3.3 V and 0.33 µF at VCC = 5 V.
2 C2- passive Negative terminal of the voltage-doubler charge-pump capacitor (C2), which connects to the charge pump between C2+ and V-.
3 V- power_out Negative charge-pump output voltage, generated and regulated by the internal charge pump and referenced to network GND.
4 RIN1 input RS-232 receiver input 1, which accepts ±25 V per the Recommended Operating Conditions and has an internal 5 kΩ load.
5 RIN2 input RS-232 receiver input 2, which accepts ±25 V per the Recommended Operating Conditions and also feeds the always-active ROUT2B output.
6 RIN3 input RS-232 receiver input 3, which accepts ±25 V per the Recommended Operating Conditions and has an internal 5 kΩ load.
7 RIN4 input RS-232 receiver input 4, which accepts ±25 V per the Recommended Operating Conditions and has an internal 5 kΩ load.
8 RIN5 input RS-232 receiver input 5, which accepts ±25 V per the Recommended Operating Conditions and has an internal 5 kΩ load.
9 DOUT1 output RS-232 driver output 1, which must stay within the ±13.2 V absolute maximum output voltage range and has a short-circuit current of ±35 to ±60 mA.
10 DOUT2 output RS-232 driver output 2, which must stay within the ±13.2 V absolute maximum output voltage range and has a short-circuit current of ±35 to ±60 mA.
11 DOUT3 output RS-232 driver output 3, which must stay within the ±13.2 V absolute maximum output voltage range and has a short-circuit current of ±35 to ±60 mA.
12 DIN3 input Driver logic input 3, which must be held at a valid low or high level (VIL max 0.8 V; VIH min 2 V at 3.3 V VCC or 2.4 V at 5 V VCC; input range 0 to 5.5 V).
13 DIN2 input Driver logic input 2, which must be held at a valid low or high level (VIL max 0.8 V; VIH min 2 V at 3.3 V VCC or 2.4 V at 5 V VCC; input range 0 to 5.5 V).
14 DIN1 input Driver logic input 1, which must be held at a valid low or high level (VIL max 0.8 V; VIH min 2 V at 3.3 V VCC or 2.4 V at 5 V VCC; input range 0 to 5.5 V).
15 ROUT5 output Receiver logic output 5, which goes high impedance when FORCEOFF is low (powered off).
16 ROUT4 output Receiver logic output 4, which goes high impedance when FORCEOFF is low (powered off).
17 ROUT3 output Receiver logic output 3, which goes high impedance when FORCEOFF is low (powered off).
18 ROUT2 output Receiver logic output 2, which goes high impedance when FORCEOFF is low (powered off).
19 ROUT1 output Receiver logic output 1, which goes high impedance when FORCEOFF is low (powered off).
20 ROUT2B output Always-active noninverting receiver output of RIN2 that stays enabled while the device is powered down, allowing ring-indicator data transmission.
21 INVALID output Invalid-data output that is high when any receiver input is a valid RS-232 level (above 2.7 V or below -2.7 V) and low when all receiver inputs are between -0.3 V and 0.3 V for more than 30 µs; it is always enabled.
22 FORCEOFF input Automatic power-down control input; driving it low powers off all drivers and receivers except ROUT2B and INVALID, and it must be tied to a valid high or low logic level (VCC or GND).
23 FORCEON input Automatic power-down control input; driving it high overrides automatic power down and keeps the drivers active, and it must be tied to a valid high or low logic level (VCC or GND).
24 C1- passive Negative terminal of the voltage-doubler charge-pump capacitor (C1), connected between C1+ and this pin.
25 GND power_in Device ground; all voltages on the device are referenced to network GND.
26 VCC power_in Supply voltage input, which must be 3 V to 5.5 V (3.3 V nominal range 3 V to 3.6 V, 5 V nominal range 4.5 V to 5.5 V).
27 V+ power_out Positive charge-pump output voltage, generated and regulated by the internal charge pump and referenced to network GND.
28 C1+ passive Positive terminal of the voltage-doubler charge-pump capacitor (C1), which the datasheet specifies as 0.1 µF at VCC = 3.3 V and 0.047 µF at VCC = 5 V.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SSOP-28-208mil
Category Interface
Pins 28

CAD (KiCad official)

  • Symbol: TRS3243CDBR
  • Footprint: Package_SO:SSOP-28_5.3x10.2mm_P0.65mm
  • 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
  • 3D model files: trs3243cdbr-etched.step / trs3243cdbr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); trs3243cdbr.step / trs3243cdbr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (26 pp, sha256 fe9a6533b614250b, retrieved 2026-10-12, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF