component
TPS92601QPWPRQ1
Public Made by Adomby adom
Texas Instruments LED Drivers, HTSSOP-20-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS92601QPWPRQ1
Texas Instruments · LED Drivers · HTSSOP-20-EP
TPS92601QPWPRQ1 from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ICTRL1 | input | LED current-control input for analog dimming of channel 1; recommended range 0 V to 3.3 V, and the internal clamp limits its effect at 1.5 V. |
| 2 | COMP1 | output | Compensation network connection for the channel 1 error amplifier; a single capacitor here sets a dominant pole for loop stability. |
| 3 | OVFB1 | input | Voltage-feedback input for channel 1 from the external output resistor divider; recommended range 0 V to 8 V, absolute maximum 80 V. |
| 4 | RT | input | Oscillator pin and input for external synchronization frequency; recommended range 0 V to 3.3 V. |
| 5 | DIAG1 | output | Channel 1 diagnostic output that signals open LED, short, and LED current as a 0.2 V to 2.85 V analog voltage; absolute maximum 3.6 V. |
| 6 | GND | power_in | Ground reference for the device; all voltages are referenced to this pin. |
| 7 | PWMIN1 | input | PWM input and channel 1 enable/disable; enable/disable range 0 V to 40 V, PWM functionality range 0 V to 7 V. |
| 8 | VIN | power_in | Supply voltage input; absolute maximum 40 V, with 6 V to 26 V specified for full functionality on first battery connection. |
| 9 | NC | unconnected | No internal connection. |
| 10 | NC | unconnected | No internal connection. |
| 11 | NC | unconnected | No internal connection. |
| 12 | NC | unconnected | No internal connection. |
| 13 | VCC | power_out | Gate-drive supply voltage that requires an external decoupling capacitor; recommended range 3 V to 8 V, absolute maximum 8.8 V. |
| 14 | GDRV1 | output | Gate driver output for the channel 1 external low-side NMOS boost FET; absolute maximum range -0.3 V to 8.8 V. |
| 15 | ISNS1 | input | Overcurrent sense input for channel 1; recommended range 0 V to 8 V. |
| 16 | PGND1 | power_in | Power ground for channel 1, which should be connected to the thermal pad. |
| 17 | ISP1 | input | Positive current-sense input for channel 1 across the high-side LED shunt; recommended common-mode range 4 V to 75 V. |
| 18 | ISN1 | input | Negative current-sense input for channel 1 across the high-side LED shunt; recommended common-mode range 4 V to 75 V. |
| 19 | VOUT1 | input | Connection to the boost output voltage for channel 1 used for output sensing; recommended range 4 V to 75 V, absolute maximum 80 V. |
| 20 | PWMO1 | output | Gate driver output for the channel 1 high-side PWM-dimming PMOS FET; absolute maximum 80 V. |
| 21 | Thermal pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 21 |
CAD (KiCad official)
- Symbol:
TPS92601QPWPRQ1 - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
tps92601qpwprq1-etched.step/tps92601qpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps92601qpwprq1.step/tps92601qpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (49 pp, sha256
1f962208c134e6a1, retrieved 2026-10-08, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).