← Commit history

Initial commit: component/tps7a8701rtjr

Ray ·f1f333d185 ·
2 files changed +279
README.mdadded+58
@@ -0,0 +1,58 @@+# TPS7A8701RTJR++**Texas Instruments** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · QFN-20-EP(4x4)++TPS7A8701RTJR from Texas Instruments, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | IN1 | power_in | Input supply pin for LDO 1 requiring 10 µF or greater input capacitor located as close as practical. |+| 2 | IN1 | power_in | Input supply pin for LDO 1 requiring 10 µF or greater input capacitor located as close as practical. |+| 3 | GND | power_in | Ground pin connected to thermal pad and each other with low-impedance connection. |+| 4 | IN2 | power_in | Input supply pin for LDO 2 requiring 10 µF or greater input capacitor located as close as practical. |+| 5 | IN2 | power_in | Input supply pin for LDO 2 requiring 10 µF or greater input capacitor located as close as practical. |+| 6 | EN2 | input | Enable pin for LDO 2; enables when VEN ≥ 1.1V, disables when VEN ≤ 0.4V; connect to IN2 if enable function not used. |+| 7 | NR/SS2 | passive | Noise-reduction and soft-start pin for LDO 2; capacitor value 10 nF to 10 µF recommended to reduce reference noise and enable soft-start function. |+| 8 | SS_CTRL2 | input | Soft-start control pin for LDO 2; connect to GND for typical soft-start or to VIN for fast charging of NR/SS capacitor. |+| 9 | PG2 | tri_state | Open-drain power-good indicator for LDO 2; requires 10 kΩ to 100 kΩ external pullup resistor; asserts when output ≥ 88.9% of target voltage. |+| 10 | FB2 | input | Feedback pin for LDO 2 error amplifier; 10 nF feed-forward capacitor from FB2 to OUT2 recommended to maximize AC performance. |+| 11 | OUT2 | output | Regulated output for LDO 2 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output. |+| 12 | OUT2 | output | Regulated output for LDO 2 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output. |+| 13 | GND | power_in | Ground pin connected to thermal pad and each other with low-impedance connection. |+| 14 | OUT1 | output | Regulated output for LDO 1 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output. |+| 15 | OUT1 | output | Regulated output for LDO 1 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output. |+| 16 | FB1 | input | Feedback pin for LDO 1 error amplifier; 10 nF feed-forward capacitor from FB1 to OUT1 recommended to maximize AC performance. |+| 17 | PG1 | tri_state | Open-drain power-good indicator for LDO 1; requires 10 kΩ to 100 kΩ external pullup resistor; asserts when output ≥ 88.9% of target voltage. |+| 18 | SS_CTRL1 | input | Soft-start control pin for LDO 1; connect to GND for typical soft-start or to VIN for fast charging of NR/SS capacitor. |+| 19 | NR/SS1 | passive | Noise-reduction and soft-start pin for LDO 1; capacitor value 10 nF to 10 µF recommended to reduce reference noise and enable soft-start function. |+| 20 | EN1 | input | Enable pin for LDO 1; enables when VEN ≥ 1.1V, disables when VEN ≤ 0.4V; connect to IN1 if enable function not used. |+| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-20-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `TPS7A8701RTJR`+- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`+- 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `tps7a8701rtjr-etched.step` / `tps7a8701rtjr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps7a8701rtjr.step` / `tps7a8701rtjr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps7a87) (48 pp, sha256 `00030644bd522fb5`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps7a8701rtjr-datasheet.pdf)
page.jsonadded+221
@@ -0,0 +1,221 @@+{+  "slug": "tps7a8701rtjr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, QFN-20-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps7a8701rtjr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps7a8701rtjr.kicad_sym",+    "tps7a8701rtjr.kicad_mod",+    "tps7a8701rtjr.glb",+    "tps7a8701rtjr.step",+    "tps7a8701rtjr.lbr",+    "docs/hero.png",+    "docs/tps7a8701rtjr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS7A8701RTJR",+    "manufacturer": "Texas Instruments",+    "package": "QFN-20-EP(4x4)",+    "pin_count": 21,+    "category": "Power Management (PMIC)",+    "subcategory": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps7a87",+    "parts": {+      "symbol": "tps7a8701rtjr.kicad_sym",+      "footprint": "tps7a8701rtjr.kicad_mod",+      "model_3d": "tps7a8701rtjr-etched.glb",+      "model_3d_plain": "tps7a8701rtjr.glb",+      "model_3d_step": "tps7a8701rtjr-etched.step",+      "model_3d_step_plain": "tps7a8701rtjr.step",+      "lbr": "tps7a8701rtjr.lbr"+    },+    "distributor_links": {+      "lcsc": "C544518"+    },+    "pins": [+      {+        "number": "1",+        "name": "IN1",+        "type": "power_in",+        "description": "Input supply pin for LDO 1 requiring 10 µF or greater input capacitor located as close as practical."+      },+      {+        "number": "2",+        "name": "IN1",+        "type": "power_in",+        "description": "Input supply pin for LDO 1 requiring 10 µF or greater input capacitor located as close as practical."+      },+      {+        "number": "3",+        "name": "GND",+        "type": "power_in",+        "description": "Ground pin connected to thermal pad and each other with low-impedance connection."+      },+      {+        "number": "4",+        "name": "IN2",+        "type": "power_in",+        "description": "Input supply pin for LDO 2 requiring 10 µF or greater input capacitor located as close as practical."+      },+      {+        "number": "5",+        "name": "IN2",+        "type": "power_in",+        "description": "Input supply pin for LDO 2 requiring 10 µF or greater input capacitor located as close as practical."+      },+      {+        "number": "6",+        "name": "EN2",+        "type": "input",+        "description": "Enable pin for LDO 2; enables when VEN ≥ 1.1V, disables when VEN ≤ 0.4V; connect to IN2 if enable function not used."+      },+      {+        "number": "7",+        "name": "NR/SS2",+        "type": "passive",+        "description": "Noise-reduction and soft-start pin for LDO 2; capacitor value 10 nF to 10 µF recommended to reduce reference noise and enable soft-start function."+      },+      {+        "number": "8",+        "name": "SS_CTRL2",+        "type": "input",+        "description": "Soft-start control pin for LDO 2; connect to GND for typical soft-start or to VIN for fast charging of NR/SS capacitor."+      },+      {+        "number": "9",+        "name": "PG2",+        "type": "tri_state",+        "description": "Open-drain power-good indicator for LDO 2; requires 10 kΩ to 100 kΩ external pullup resistor; asserts when output ≥ 88.9% of target voltage."+      },+      {+        "number": "10",+        "name": "FB2",+        "type": "input",+        "description": "Feedback pin for LDO 2 error amplifier; 10 nF feed-forward capacitor from FB2 to OUT2 recommended to maximize AC performance."+      },+      {+        "number": "11",+        "name": "OUT2",+        "type": "output",+        "description": "Regulated output for LDO 2 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output."+      },+      {+        "number": "12",+        "name": "OUT2",+        "type": "output",+        "description": "Regulated output for LDO 2 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output."+      },+      {+        "number": "13",+        "name": "GND",+        "type": "power_in",+        "description": "Ground pin connected to thermal pad and each other with low-impedance connection."+      },+      {+        "number": "14",+        "name": "OUT1",+        "type": "output",+        "description": "Regulated output for LDO 1 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output."+      },+      {+        "number": "15",+        "name": "OUT1",+        "type": "output",+        "description": "Regulated output for LDO 1 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output."+      },+      {+        "number": "16",+        "name": "FB1",+        "type": "input",+        "description": "Feedback pin for LDO 1 error amplifier; 10 nF feed-forward capacitor from FB1 to OUT1 recommended to maximize AC performance."+      },+      {+        "number": "17",+        "name": "PG1",+        "type": "tri_state",+        "description": "Open-drain power-good indicator for LDO 1; requires 10 kΩ to 100 kΩ external pullup resistor; asserts when output ≥ 88.9% of target voltage."+      },+      {+        "number": "18",+        "name": "SS_CTRL1",+        "type": "input",+        "description": "Soft-start control pin for LDO 1; connect to GND for typical soft-start or to VIN for fast charging of NR/SS capacitor."+      },+      {+        "number": "19",+        "name": "NR/SS1",+        "type": "passive",+        "description": "Noise-reduction and soft-start pin for LDO 1; capacitor value 10 nF to 10 µF recommended to reduce reference noise and enable soft-start function."+      },+      {+        "number": "20",+        "name": "EN1",+        "type": "input",+        "description": "Enable pin for LDO 1; enables when VEN ≥ 1.1V, disables when VEN ≤ 0.4V; connect to IN1 if enable function not used."+      },+      {+        "number": "21",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 21 added from the footprint"+        ],+        "pages_sent": 48,+        "cost_usd": 0.492,+        "at": "2026-09-23T01:16:50"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps7a87",+        "pages": 48,+        "sha256": "00030644bd522fb5",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 21,+        "described": 21,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file