main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs tps7a4901dgnt: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers tps7a4901dgnt: viewers · Ray
package.json tps7a4901dgnt: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json tps7a4901dgnt: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/tps7a4901dgnt · Ray
tps7a4901dgnt-etched.fit.json tps7a4901dgnt: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps7a4901dgnt-etched.glb tps7a4901dgnt: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps7a4901dgnt-etched.step tps7a4901dgnt: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps7a4901dgnt.glb Publish 0.1.0 · Ray
tps7a4901dgnt.kicad_mod Publish 0.1.0 · Ray
tps7a4901dgnt.kicad_sym Publish 0.1.0 · Ray
tps7a4901dgnt.lbr Publish 0.1.0 · Ray
tps7a4901dgnt.step Publish 0.1.0 · Ray

TPS7A4901DGNT

Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · MSOP-8-EP

TPS7A4901DGNT from Texas Instruments, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT output Regulator output; a capacitor ≥ 2.2 µF must be tied from this pin to ground to ensure stability.
2 FB input Input to the error amplifier; FB is used to set the output voltage of the device.
3 NC unconnected Not internally connected; this pin can either be left open or tied to GND.
4 GND power_in Ground pin, must be tied directly to the PowerPAD under the device.
5 EN input Enable input that turns the regulator on when VEN ≥ VEN(high) and off when VEN ≤ VEN(low); can be connected to IN if not used, VEN ≤ VIN.
6 NR/SS passive Noise-reduction/soft-start pin; an external capacitor here bypasses band-gap noise to reduce RMS output noise and sets the soft-start ramp time.
7 DNC unconnected Do not connect; do not route this pin to any electrical net, not even GND or IN.
8 IN power_in Input supply pin, input voltage range 3 V to 35 V (recommended operating conditions).
9 PowerPAD power_in Exposed thermal pad; must be either left open or tied to ground, and should be soldered to the PCB ground plane to enhance thermal performance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package MSOP-8-EP
Category Power Management (PMIC)
Pins 9

CAD (KiCad official)

  • Symbol: TPS7A4901DGNT
  • Footprint: Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm
  • 3D model: MSOP-8-EP (KiCad packages3D, STEP)
  • 3D model files: tps7a4901dgnt-etched.step / tps7a4901dgnt-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps7a4901dgnt.step / tps7a4901dgnt.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (39 pp, sha256 f69e957b22bcc2db, retrieved 2026-09-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF