main
Ray
Publish 0.1.0
ee67a98
TPS78511QKVURQ1
Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · TO-252-4
TPS78511QKVURQ1 from Texas Instruments, in a TO-252-4. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Active-high enable: driving above VEN(HI) (0.9 V typical) enables the device and below VEN(LOW) (0.3 V) disables it, with the recommended EN voltage range 0 V to 6 V; do not float this pin, and connect EN to IN if shutdown is not used. |
| 2 | IN | power_in | Input supply pin, with an input voltage range of 1.7 V to 6.0 V; place a 0.1 µF to 1 µF (nominal recommended value or larger) ceramic capacitor from IN to GND as close to the device as possible. |
| 3 | GND | power_in | Ground pin that must be connected to board ground; the thermal pad is electrically connected to this pin. |
| 4 | OUT | power_out | Regulated output with up to 1 A output current; a minimum of 0.47 µF effective capacitance to ground is required for stability, and a 1 µF or larger ceramic capacitor is recommended for best transient response, placed as close to the pin as possible. |
| 5 | NC | unconnected | No-connect pin on the fixed-voltage version that is not internally connected; connect to ground for best thermal performance or leave floating. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TO-252-4 |
| Category | Power Management (PMIC) |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 1.7 | 6 | V | 7 | ||
| Output voltage (fixed output) | VOUT | 0.65 | 5 | V | Fixed output | 7 | |
| Output accuracy | VOUT | -0.5 | 0.5 | % | 1 mA ≤ IOUT ≤ 1 A; VOUT(nom) + 0.75 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; TJ = 25°C | 7 | |
| Output accuracy | VOUT | -1 | 1 | % | 1 mA ≤ IOUT ≤ 1 A; VOUT(nom) + 0.75 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 | |
| Output accuracy | VOUT | -1.7 | 1.7 | % | 1 mA ≤ IOUT ≤ 1 A; VOUT(nom) + 0.75 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 150°C | 7 | |
| Load regulation | VOUT | -7.5 | 7.5 | mV | 0.1 mA ≤ IOUT ≤ 1 A; -40°C ≤ TJ ≤ 85°C | 7 | |
| Load regulation | VOUT | -7.5 | 15 | mV | 0.1 mA ≤ IOUT ≤ 1 A, -40°C ≤ TJ ≤ 150°C; VOUT ≤ 3.3 V | 7 | |
| Ground current | IGND | 15 | 25 | 33 | µA | IOUT = 0 mA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; TJ = 25°C | 7 |
| Ground current | IGND | 35 | µA | IOUT = 0 mA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 | ||
| Ground current | IGND | 40 | µA | IOUT = 0 mA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 150°C | 7 | ||
| Ground current | IGND | 33 | 44 | µA | IOUT = 500 µA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; TJ = 25°C | 7 | |
| Ground current | IGND | 47 | µA | IOUT = 500 µA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 | ||
| Ground current | IGND | 50 | µA | IOUT = 500 µA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 150°C | 7 | ||
| Ground current | IGND | 45 | µA | IOUT = 100 µA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 | ||
| Shutdown current | ISHDN | 0.01 | 0.05 | µA | VEN ≤ 0.3 V; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; TJ = 25°C | 7 | |
| Shutdown current | ISHDN | 0.25 | µA | VEN ≤ 0.3 V; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 | ||
| Shutdown current | ISHDN | 3 | µA | VEN ≤ 0.3 V; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 150°C | 7 | ||
| Output current limit | ICL | 1.04 | 1.65 | A | VIN = VOUT(nom) + 1.25 V or 2.0 V (whichever is greater); VOUT = 0.9 x VOUT(nom) | 7 | |
| Dropout voltage (KVU package) | VDO | 915 | mV | 1.0 V ≤ VOUT < 1.2 V; IOUT = 1 A, VOUT = 0.95 x VOUT(nom) | 8 | ||
| UVLO threshold, VIN rising | VUVLO | 1.28 | 1.42 | 1.62 | V | VIN rising | 8 |
| UVLO threshold, VIN falling | VUVLO | 1.17 | 1.29 | 1.42 | V | VIN falling | 8 |
| Start-up time | tSTR | 280 | 550 | 785 | µs | From EN low-to-high transition to VOUT = VOUT(nom) x 92% | 8 |
| EN pin logic high voltage | VEN(HI) | 0.9 | V | 8 | |||
| EN pin logic low voltage | VEN(LOW) | 0.3 | V | 8 | |||
| Input voltage | VIN | 1.7 | 6 | V | 6 | ||
| Output voltage (fixed output) | VOUT | 0.65 | 5 | V | Fixed output | 6 | |
| Input capacitor | CIN | 0.1 | 1 | µF | 6 | ||
| Output capacitor | COUT | 1 | 200 | µF | Minimum effective capacitance is 0.47 µF | 6 | |
| Feed-forward capacitor | CFF | 0 | 10 | 100 | nF | Optional, not required for stability | 6 |
| Output current | IOUT | 0 | 1 | A | 6 | ||
| Output capacitor ESR | COUT,ESR | 0.001 | 1 | Ω | 6 | ||
| Enable voltage | VEN | 0 | 6 | V | 6 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 6 | ||
| Supply voltage | VIN | -0.3 | 6.5 | V | 5 | ||
| Enable voltage | VEN | -0.3 | 6.5 | V | 5 | ||
| Output voltage | VOUT | -0.3 | V | Maximum is VIN + 0.3 V or 6.5 V, whichever is smaller | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Junction-to-ambient thermal resistance (KVU, TO-252) | RθJA | 31.6 | °C/W | KVU (TO-252), 5 pins | 6 | ||
| Junction-to-case (top) thermal resistance (KVU) | RθJC(top) | 40.4 | °C/W | KVU (TO-252), 5 pins | 6 | ||
| Junction-to-board thermal resistance (KVU) | RθJB | 10.4 | °C/W | KVU (TO-252), 5 pins | 6 | ||
| Junction-to-top characterization parameter (KVU) | ψJT | 4.6 | °C/W | KVU (TO-252), 5 pins | 6 | ||
| Junction-to-board characterization parameter (KVU) | ψJB | 10.3 | °C/W | KVU (TO-252), 5 pins | 6 | ||
| Junction-to-case (bottom) thermal resistance (KVU) | RθJC(bot) | 3.3 | °C/W | KVU (TO-252), 5 pins | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | copper ground plane on the layer directly underneath the LDO circuitry and FB pin to minimize any undesirable | 28 |
CAD (KiCad official)
- Symbol:
TPS78511QKVURQ1 - Footprint:
Package_TO_SOT_SMD:TO-252-4 - 3D model: TO-252-4 (KiCad packages3D, STEP)
- 3D model files:
tps78511qkvurq1-etched.step/tps78511qkvurq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps78511qkvurq1.step/tps78511qkvurq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (46 pp, sha256
8d1b76473f2a1cce, retrieved 2026-11-10, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS78511QKVURQ1
**Texas Instruments** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · TO-252-4
TPS78511QKVURQ1 from Texas Instruments, in a TO-252-4. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Active-high enable: driving above VEN(HI) (0.9 V typical) enables the device and below VEN(LOW) (0.3 V) disables it, with the recommended EN voltage range 0 V to 6 V; do not float this pin, and connect EN to IN if shutdown is not used. |
| 2 | IN | power_in | Input supply pin, with an input voltage range of 1.7 V to 6.0 V; place a 0.1 µF to 1 µF (nominal recommended value or larger) ceramic capacitor from IN to GND as close to the device as possible. |
| 3 | GND | power_in | Ground pin that must be connected to board ground; the thermal pad is electrically connected to this pin. |
| 4 | OUT | power_out | Regulated output with up to 1 A output current; a minimum of 0.47 µF effective capacitance to ground is required for stability, and a 1 µF or larger ceramic capacitor is recommended for best transient response, placed as close to the pin as possible. |
| 5 | NC | unconnected | No-connect pin on the fixed-voltage version that is not internally connected; connect to ground for best thermal performance or leave floating. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TO-252-4 |
| Category | Power Management (PMIC) |
| Pins | 5 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 1.7 | | 6 | V | | 7 |
| Output voltage (fixed output) | VOUT | 0.65 | | 5 | V | Fixed output | 7 |
| Output accuracy | VOUT | -0.5 | | 0.5 | % | 1 mA ≤ IOUT ≤ 1 A; VOUT(nom) + 0.75 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; TJ = 25°C | 7 |
| Output accuracy | VOUT | -1 | | 1 | % | 1 mA ≤ IOUT ≤ 1 A; VOUT(nom) + 0.75 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 |
| Output accuracy | VOUT | -1.7 | | 1.7 | % | 1 mA ≤ IOUT ≤ 1 A; VOUT(nom) + 0.75 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 150°C | 7 |
| Load regulation | VOUT | -7.5 | | 7.5 | mV | 0.1 mA ≤ IOUT ≤ 1 A; -40°C ≤ TJ ≤ 85°C | 7 |
| Load regulation | VOUT | -7.5 | | 15 | mV | 0.1 mA ≤ IOUT ≤ 1 A, -40°C ≤ TJ ≤ 150°C; VOUT ≤ 3.3 V | 7 |
| Ground current | IGND | 15 | 25 | 33 | µA | IOUT = 0 mA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; TJ = 25°C | 7 |
| Ground current | IGND | | | 35 | µA | IOUT = 0 mA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 |
| Ground current | IGND | | | 40 | µA | IOUT = 0 mA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 150°C | 7 |
| Ground current | IGND | | 33 | 44 | µA | IOUT = 500 µA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; TJ = 25°C | 7 |
| Ground current | IGND | | | 47 | µA | IOUT = 500 µA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 |
| Ground current | IGND | | | 50 | µA | IOUT = 500 µA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 150°C | 7 |
| Ground current | IGND | | | 45 | µA | IOUT = 100 µA; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 |
| Shutdown current | ISHDN | | 0.01 | 0.05 | µA | VEN ≤ 0.3 V; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; TJ = 25°C | 7 |
| Shutdown current | ISHDN | | | 0.25 | µA | VEN ≤ 0.3 V; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 85°C | 7 |
| Shutdown current | ISHDN | | | 3 | µA | VEN ≤ 0.3 V; VOUT(nom) + 0.5 V or 2.0 V (whichever is greater) ≤ VIN ≤ 6.0 V; -40°C ≤ TJ ≤ 150°C | 7 |
| Output current limit | ICL | 1.04 | | 1.65 | A | VIN = VOUT(nom) + 1.25 V or 2.0 V (whichever is greater); VOUT = 0.9 x VOUT(nom) | 7 |
| Dropout voltage (KVU package) | VDO | | | 915 | mV | 1.0 V ≤ VOUT < 1.2 V; IOUT = 1 A, VOUT = 0.95 x VOUT(nom) | 8 |
| UVLO threshold, VIN rising | VUVLO | 1.28 | 1.42 | 1.62 | V | VIN rising | 8 |
| UVLO threshold, VIN falling | VUVLO | 1.17 | 1.29 | 1.42 | V | VIN falling | 8 |
| Start-up time | tSTR | 280 | 550 | 785 | µs | From EN low-to-high transition to VOUT = VOUT(nom) x 92% | 8 |
| EN pin logic high voltage | VEN(HI) | 0.9 | | | V | | 8 |
| EN pin logic low voltage | VEN(LOW) | | | 0.3 | V | | 8 |
| Input voltage | VIN | 1.7 | | 6 | V | | 6 |
| Output voltage (fixed output) | VOUT | 0.65 | | 5 | V | Fixed output | 6 |
| Input capacitor | CIN | 0.1 | 1 | | µF | | 6 |
| Output capacitor | COUT | 1 | | 200 | µF | Minimum effective capacitance is 0.47 µF | 6 |
| Feed-forward capacitor | CFF | 0 | 10 | 100 | nF | Optional, not required for stability | 6 |
| Output current | IOUT | 0 | | 1 | A | | 6 |
| Output capacitor ESR | COUT,ESR | 0.001 | | 1 | Ω | | 6 |
| Enable voltage | VEN | 0 | | 6 | V | | 6 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 6 |
| Supply voltage | VIN | -0.3 | | 6.5 | V | | 5 |
| Enable voltage | VEN | -0.3 | | 6.5 | V | | 5 |
| Output voltage | VOUT | -0.3 | | | V | Maximum is VIN + 0.3 V or 6.5 V, whichever is smaller | 5 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 5 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 5 |
| Junction-to-ambient thermal resistance (KVU, TO-252) | RθJA | | 31.6 | | °C/W | KVU (TO-252), 5 pins | 6 |
| Junction-to-case (top) thermal resistance (KVU) | RθJC(top) | | 40.4 | | °C/W | KVU (TO-252), 5 pins | 6 |
| Junction-to-board thermal resistance (KVU) | RθJB | | 10.4 | | °C/W | KVU (TO-252), 5 pins | 6 |
| Junction-to-top characterization parameter (KVU) | ψJT | | 4.6 | | °C/W | KVU (TO-252), 5 pins | 6 |
| Junction-to-board characterization parameter (KVU) | ψJB | | 10.3 | | °C/W | KVU (TO-252), 5 pins | 6 |
| Junction-to-case (bottom) thermal resistance (KVU) | RθJC(bot) | | 3.3 | | °C/W | KVU (TO-252), 5 pins | 6 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | copper ground plane on the layer directly underneath the LDO circuitry and FB pin to minimize any undesirable | 28 |
## CAD (KiCad official)
- Symbol: `TPS78511QKVURQ1`
- Footprint: `Package_TO_SOT_SMD:TO-252-4`
- 3D model: TO-252-4 (KiCad packages3D, STEP)
- 3D model files: `tps78511qkvurq1-etched.step` / `tps78511qkvurq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps78511qkvurq1.step` / `tps78511qkvurq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps785-q1) (46 pp, sha256 `8d1b76473f2a1cce`, retrieved 2026-11-10, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps78511qkvurq1-datasheet.pdf)