component
TPS76715QPWP
Public Made by Adomby adom
Texas Instruments Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, HTSSOP-20. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS76715QPWP
Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · HTSSOP-20
TPS76715QPWP from Texas Instruments, in a HTSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND/HSINK | power_in | Ground/heatsink pin; the datasheet lists it with the regulator ground as the package heatsink connection. |
| 2 | GND/HSINK | power_in | Ground/heatsink pin; the datasheet lists it with the regulator ground as the package heatsink connection. |
| 3 | GND | power_in | Regulator ground pin; all voltage limits in the datasheet are referenced to network terminal ground. |
| 4 | NC | unconnected | No internal connection. |
| 5 | EN | input | Enable input; a TTL high signal shuts the regulator down into sleep mode, EN voltage is limited to -0.3 V to VI + 0.3 V, and EN should be tied to ground if shutdown is not used. |
| 6 | IN | power_in | Input voltage pin; recommended input range is 2.7 V to 10 V with an absolute maximum of 13.5 V. |
| 7 | IN | power_in | Input voltage pin; recommended input range is 2.7 V to 10 V with an absolute maximum of 13.5 V. |
| 8 | NC | unconnected | No internal connection. |
| 9 | GND/HSINK | power_in | Ground/heatsink pin; the datasheet lists it with the regulator ground as the package heatsink connection. |
| 10 | GND/HSINK | power_in | Ground/heatsink pin; the datasheet lists it with the regulator ground as the package heatsink connection. |
| 11 | GND/HSINK | power_in | Ground/heatsink pin; the datasheet lists it with the regulator ground as the package heatsink connection. |
| 12 | GND/HSINK | power_in | Ground/heatsink pin; the datasheet lists it with the regulator ground as the package heatsink connection. |
| 13 | OUT | power_out | Regulated output pin; output current is 0 to 1.0 A and the absolute maximum output voltage is 7 V. |
| 14 | OUT | power_out | Regulated output pin; output current is 0 to 1.0 A and the absolute maximum output voltage is 7 V. |
| 15 | FB/NC | input | Feedback input for the adjustable version only; for fixed-output options such as the TPS76715 (1.5 V) it is a no connect. |
| 16 | RESET | output | Open-drain reset output that pulls low when the output falls to between 92% and 98% of nominal, requires a pull-up resistor, and has a maximum voltage of 16.5 V. |
| 17 | NC | unconnected | No internal connection. |
| 18 | NC | unconnected | No internal connection. |
| 19 | GND/HSINK | power_in | Ground/heatsink pin; the datasheet lists it with the regulator ground as the package heatsink connection. |
| 20 | GND/HSINK | power_in | Ground/heatsink pin; the datasheet lists it with the regulator ground as the package heatsink connection. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20 |
| Category | Power Management (PMIC) |
| Pins | 21 |
CAD (KiCad official)
- Symbol:
TPS76715QPWP - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: HTSSOP-20, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
tps76715qpwp-etched.step/tps76715qpwp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps76715qpwp.step/tps76715qpwp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (37 pp, sha256
8fecf68765895723, retrieved 2026-10-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).