component
TPS74801RGWT
Public Made by Adomby adom
Texas Instruments Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, VQFN-20-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS74801RGWT
Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · VQFN-20-EP(5x5)
TPS74801RGWT from Texas Instruments, in a VQFN-20-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | output | Regulated output voltage; small capacitor (≥2.2μF ceramic) required from this pin to ground to assure stability. |
| 2 | NC | unconnected | No connection; pin can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 3 | NC | unconnected | No connection; pin can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 4 | NC | unconnected | No connection; pin can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 5 | IN | input | Input to the device; 1-µF or larger input capacitor recommended for optimal performance. |
| 6 | IN | input | Input to the device; 1-µF or larger input capacitor recommended for optimal performance. |
| 7 | IN | input | Input to the device; 1-µF or larger input capacitor recommended for optimal performance. |
| 8 | IN | input | Input to the device; 1-µF or larger input capacitor recommended for optimal performance. |
| 9 | PG | output | Power Good pin; open-drain active-high output indicating VOUT status; pull-up resistor (10kΩ to 1MΩ) to 5.5V supply recommended, or pin can be left unconnected if output monitoring not required. |
| 10 | BIAS | input | Bias input voltage for error amplifier, reference, and internal control circuits; 1-µF or larger input capacitor recommended; 4.7-µF or larger required if IN is connected to BIAS. |
| 11 | EN | input | Enable pin; driving high enables the regulator, driving low puts regulator into shutdown mode; must not be left unconnected. |
| 12 | GND | power_in | Ground reference. |
| 13 | NC | unconnected | No connection; pin can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 14 | NC | unconnected | No connection; pin can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 15 | SS | input | Soft-Start pin; capacitor connected from this pin to ground sets the start-up time; typical soft-start ramp time is 200μs if pin is left unconnected. |
| 16 | FB | input | Feedback pin for center tap connection to external resistor divider network that sets output voltage; must not be left floating. |
| 17 | NC | unconnected | No connection; pin can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 18 | OUT | output | Regulated output voltage; small capacitor (≥2.2μF ceramic) required from this pin to ground to assure stability. |
| 19 | OUT | output | Regulated output voltage; small capacitor (≥2.2μF ceramic) required from this pin to ground to assure stability. |
| 20 | OUT | output | Regulated output voltage; small capacitor (≥2.2μF ceramic) required from this pin to ground to assure stability. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-20-EP(5x5) |
| Category | Power Management (PMIC) |
| Pins | 21 |
CAD (KiCad official)
- Symbol:
TPS74801RGWT - Footprint:
Package_DFN_QFN:QFN-20-1EP_5x5mm_P0.65mm_EP3.35x3.35mm - 3D model: VQFN-20-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
tps74801rgwt-etched.step/tps74801rgwt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps74801rgwt.step/tps74801rgwt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (47 pp, sha256
369b0359367aaa2b, retrieved 2026-10-06, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).