main
Ray
Publish 0.1.0
2528c92
TPS74201RGRR
Texas Instruments · Linear Voltage Regulators (LDO) · VQFN-20-EP(3.5x3.5)
TPS74201RGRR from Texas Instruments, in a VQFN-20-EP(3.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Regulated output voltage; no capacitor is required on this pin for stability. |
| 2 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 3 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 4 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 5 | IN | power_in | Unregulated input to the device. |
| 6 | IN | power_in | Unregulated input to the device. |
| 7 | IN | power_in | Unregulated input to the device. |
| 8 | IN | power_in | Unregulated input to the device. |
| 9 | PG | output | Open-drain active-high power-good output that goes high-impedance when VOUT exceeds the PG trip threshold; use a 10 kΩ to 1 MΩ pullup to a supply up to 5.5 V, or leave floating if unused. |
| 10 | BIAS | power_in | Bias input voltage for the error amplifier, reference, and internal control circuits. |
| 11 | EN | input | Enable pin: high enables the regulator, low puts it into shutdown; must not be left floating. |
| 12 | GND | power_in | Ground. |
| 13 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 14 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 15 | SS | passive | Soft-start pin; a capacitor to ground sets the start-up time, and if left floating the soft-start ramp time is typically 100 μs. |
| 16 | FB | input | Feedback connection to the center tap of the external resistor divider that sets the output voltage; must not be left floating (adjustable version). |
| 17 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 18 | OUT | power_out | Regulated output voltage; no capacitor is required on this pin for stability. |
| 19 | OUT | power_out | Regulated output voltage; no capacitor is required on this pin for stability. |
| 20 | OUT | power_out | Regulated output voltage; no capacitor is required on this pin for stability. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-20-EP(3.5x3.5) |
| Category | Power Supply Chip |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 5.5 | V | min = VOUT + VDO | 7 | ||
| Bias pin voltage | VBIAS | 2.375 | 5.25 | V | 7 | ||
| Internal reference (adjustable) | VREF | 0.796 | 0.8 | 0.804 | V | TJ = 25°C | 7 |
| Output voltage accuracy | VOUT | -1 | 0.2 | 1 | % | 2.375 V ≤ VBIAS ≤ 5.25 V, VOUT + 1.62 V ≤ VBIAS, 50 mA ≤ IOUT ≤ 1.5 A | 7 |
| Line regulation (VQFN) | ΔVOUT/ΔVIN | 0.0005 | 0.05 | %/V | VOUT(NOM) + 0.3 ≤ VIN ≤ 5.5 V, VQFN | 7 | |
| VIN dropout voltage (VQFN) | VDO | 55 | 100 | mV | IOUT = 1.5 A, VBIAS, VOUT(NOM) ≥ 1.62 V, VQFN | 7 | |
| Current limit | ICL | 1.8 | 4 | A | VOUT = 80% × VOUT(NOM) | 7 | |
| Bias pin current | IBIAS | 2 | 4 | mA | IOUT = 0 mA to 1.5 A | 7 | |
| Shutdown supply current (VIN) | ISHDN | 1 | 100 | μA | VEN ≤ 0.4 V | 7 | |
| Feedback pin current | IFB | -250 | 68 | 250 | nA | IOUT = 50 mA to 1.5 A | 7 |
| Soft-start charging current | ISS | 0.5 | 0.73 | 1 | μA | VSS = 0.4 V | 7 |
| Enable input high level | VEN,HI | 1.1 | 5.5 | V | 7 | ||
| Enable input low level | VEN,LO | 0 | 0.4 | V | 7 | ||
| Enable pin current | IEN | 0.1 | 1 | μA | VEN = 5 V | 7 | |
| PG trip threshold | VIT | 86.5 | 90 | 93.5 | %VOUT | VOUT decreasing | 7 |
| PG output low voltage | VPG,LO | 0.3 | V | IPG = 1 mA (sinking), VOUT < VIT | 7 | ||
| PG leakage current | IPG,LKG | 0.03 | 1 | μA | VPG = 5.25 V, VOUT > VIT | 7 | |
| Operating junction temperature | TJ | -40 | 125 | °C | 7 | ||
| Input/bias voltage abs max | VIN, VBIAS | -0.3 | 6 | V | 5 | ||
| Enable voltage | VEN | -0.3 | 6 | V | 5 | ||
| Power-good voltage | VPG | -0.3 | 6 | V | 5 | ||
| PG sink current | IPG | 0 | 1.5 | mA | 5 | ||
| SS pin voltage | VSS | -0.3 | 6 | V | 5 | ||
| Feedback pin voltage | VFB | -0.3 | 6 | V | 5 | ||
| Output voltage | VOUT | -0.3 | V | max = VIN + 0.3 V | 5 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 5 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | HBM, ANSI/ESDA/JEDEC JS-001 | 5 | |
| ESD CDM | V(ESD) | -500 | 500 | V | CDM, JESD22-C101 | 5 | |
| Output current | IOUT | 0 | 1.5 | A | 5 | ||
| Enable supply voltage | VEN | 0 | 5.5 | V | 5 | ||
| Input capacitor | CIN | 1 | µF | 5 | |||
| Bias capacitor | CBIAS | 1 | µF | 5 | |||
| Junction-to-ambient thermal resistance | RθJA | 39.1 | °C/W | RGR (VQFN) 20 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 29.3 | °C/W | RGR (VQFN) | 6 | ||
| Junction-to-board thermal resistance | RθJB | 10.2 | °C/W | RGR (VQFN) | 6 | ||
| Junction-to-top characterization parameter | ψJT | 0.4 | °C/W | RGR (VQFN) | 6 | ||
| Junction-to-board characterization parameter | ψJB | 10.1 | °C/W | RGR (VQFN) | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 2 | °C/W | RGR (VQFN) | 6 |
CAD (KiCad official)
- Symbol:
TPS74201RGRR - Footprint:
Package_DFN_QFN:QFN-20-1EP_3.5x3.5mm_P0.5mm_EP2x2mm - 3D model: VQFN-20-EP(3.5x3.5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.9 mm nominal QFN height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
tps74201rgrr-etched.step/tps74201rgrr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps74201rgrr.step/tps74201rgrr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
3d8c3c0b3be915cc, retrieved 2026-10-26, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS74201RGRR
**Texas Instruments** · Linear Voltage Regulators (LDO) · VQFN-20-EP(3.5x3.5)
TPS74201RGRR from Texas Instruments, in a VQFN-20-EP(3.5x3.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Regulated output voltage; no capacitor is required on this pin for stability. |
| 2 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 3 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 4 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 5 | IN | power_in | Unregulated input to the device. |
| 6 | IN | power_in | Unregulated input to the device. |
| 7 | IN | power_in | Unregulated input to the device. |
| 8 | IN | power_in | Unregulated input to the device. |
| 9 | PG | output | Open-drain active-high power-good output that goes high-impedance when VOUT exceeds the PG trip threshold; use a 10 kΩ to 1 MΩ pullup to a supply up to 5.5 V, or leave floating if unused. |
| 10 | BIAS | power_in | Bias input voltage for the error amplifier, reference, and internal control circuits. |
| 11 | EN | input | Enable pin: high enables the regulator, low puts it into shutdown; must not be left floating. |
| 12 | GND | power_in | Ground. |
| 13 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 14 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 15 | SS | passive | Soft-start pin; a capacitor to ground sets the start-up time, and if left floating the soft-start ramp time is typically 100 μs. |
| 16 | FB | input | Feedback connection to the center tap of the external resistor divider that sets the output voltage; must not be left floating (adjustable version). |
| 17 | NC | unconnected | No connection; can be left floating or connected to GND for better thermal contact to the top-side plane. |
| 18 | OUT | power_out | Regulated output voltage; no capacitor is required on this pin for stability. |
| 19 | OUT | power_out | Regulated output voltage; no capacitor is required on this pin for stability. |
| 20 | OUT | power_out | Regulated output voltage; no capacitor is required on this pin for stability. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-20-EP(3.5x3.5) |
| Category | Power Supply Chip |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | | | 5.5 | V | min = VOUT + VDO | 7 |
| Bias pin voltage | VBIAS | 2.375 | | 5.25 | V | | 7 |
| Internal reference (adjustable) | VREF | 0.796 | 0.8 | 0.804 | V | TJ = 25°C | 7 |
| Output voltage accuracy | VOUT | -1 | 0.2 | 1 | % | 2.375 V ≤ VBIAS ≤ 5.25 V, VOUT + 1.62 V ≤ VBIAS, 50 mA ≤ IOUT ≤ 1.5 A | 7 |
| Line regulation (VQFN) | ΔVOUT/ΔVIN | | 0.0005 | 0.05 | %/V | VOUT(NOM) + 0.3 ≤ VIN ≤ 5.5 V, VQFN | 7 |
| VIN dropout voltage (VQFN) | VDO | | 55 | 100 | mV | IOUT = 1.5 A, VBIAS, VOUT(NOM) ≥ 1.62 V, VQFN | 7 |
| Current limit | ICL | 1.8 | | 4 | A | VOUT = 80% × VOUT(NOM) | 7 |
| Bias pin current | IBIAS | | 2 | 4 | mA | IOUT = 0 mA to 1.5 A | 7 |
| Shutdown supply current (VIN) | ISHDN | | 1 | 100 | μA | VEN ≤ 0.4 V | 7 |
| Feedback pin current | IFB | -250 | 68 | 250 | nA | IOUT = 50 mA to 1.5 A | 7 |
| Soft-start charging current | ISS | 0.5 | 0.73 | 1 | μA | VSS = 0.4 V | 7 |
| Enable input high level | VEN,HI | 1.1 | | 5.5 | V | | 7 |
| Enable input low level | VEN,LO | 0 | | 0.4 | V | | 7 |
| Enable pin current | IEN | | 0.1 | 1 | μA | VEN = 5 V | 7 |
| PG trip threshold | VIT | 86.5 | 90 | 93.5 | %VOUT | VOUT decreasing | 7 |
| PG output low voltage | VPG,LO | | | 0.3 | V | IPG = 1 mA (sinking), VOUT < VIT | 7 |
| PG leakage current | IPG,LKG | | 0.03 | 1 | μA | VPG = 5.25 V, VOUT > VIT | 7 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 7 |
| Input/bias voltage abs max | VIN, VBIAS | -0.3 | | 6 | V | | 5 |
| Enable voltage | VEN | -0.3 | | 6 | V | | 5 |
| Power-good voltage | VPG | -0.3 | | 6 | V | | 5 |
| PG sink current | IPG | 0 | | 1.5 | mA | | 5 |
| SS pin voltage | VSS | -0.3 | | 6 | V | | 5 |
| Feedback pin voltage | VFB | -0.3 | | 6 | V | | 5 |
| Output voltage | VOUT | -0.3 | | | V | max = VIN + 0.3 V | 5 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 5 |
| Storage temperature | Tstg | -55 | | 150 | °C | | 5 |
| ESD HBM | V(ESD) | -2000 | | 2000 | V | HBM, ANSI/ESDA/JEDEC JS-001 | 5 |
| ESD CDM | V(ESD) | -500 | | 500 | V | CDM, JESD22-C101 | 5 |
| Output current | IOUT | 0 | | 1.5 | A | | 5 |
| Enable supply voltage | VEN | 0 | | 5.5 | V | | 5 |
| Input capacitor | CIN | 1 | | | µF | | 5 |
| Bias capacitor | CBIAS | 1 | | | µF | | 5 |
| Junction-to-ambient thermal resistance | RθJA | | 39.1 | | °C/W | RGR (VQFN) 20 pins | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 29.3 | | °C/W | RGR (VQFN) | 6 |
| Junction-to-board thermal resistance | RθJB | | 10.2 | | °C/W | RGR (VQFN) | 6 |
| Junction-to-top characterization parameter | ψJT | | 0.4 | | °C/W | RGR (VQFN) | 6 |
| Junction-to-board characterization parameter | ψJB | | 10.1 | | °C/W | RGR (VQFN) | 6 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 2 | | °C/W | RGR (VQFN) | 6 |
## CAD (KiCad official)
- Symbol: `TPS74201RGRR`
- Footprint: `Package_DFN_QFN:QFN-20-1EP_3.5x3.5mm_P0.5mm_EP2x2mm`
- 3D model: VQFN-20-EP(3.5x3.5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.9 mm nominal QFN height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `tps74201rgrr-etched.step` / `tps74201rgrr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps74201rgrr.step` / `tps74201rgrr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps74201rgrr.pdf) (40 pp, sha256 `3d8c3c0b3be915cc`, retrieved 2026-10-26, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps74201rgrr-datasheet.pdf)