main
History Download
Ray Publish 0.1.0 b958288

TPS70102PWP

Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · HTSSOP-20-EP

TPS70102PWP from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connection; the pin is not internally connected and is listed as NC in the terminal table.
2 VIN1 power_in Input voltage of regulator 1; recommended input range is 2.7 V to 6 V and the internal bias is powered from VIN1, with UVLO threshold of 2.4 V to 2.65 V.
3 VIN1 power_in Input voltage of regulator 1; recommended input range is 2.7 V to 6 V and the internal bias is powered from VIN1, with UVLO threshold of 2.4 V to 2.65 V.
4 MR1 input Manual reset input 1, active low, pulled up internally to VIN1 through a 6 mA source; logic low (≤0.7 V) triggers a RESET.
5 MR2 input Manual reset input 2, active low, pulled up internally to VIN1 through a 6 mA source; logic low (≤0.7 V) triggers a RESET.
6 EN input Active-low enable: a high level (≥2 V) puts the device in shutdown, a low level (≤0.7 V) enables it, and the input current is limited to -1 mA to 1 mA.
7 SEQ input Power-up sequence control: high or open sets VOUT2 to power up first and low sets VOUT1 first; it has a 6 mA internal pull-up to VIN1 and thresholds of 2 V (high) and 0.7 V (low).
8 GND power_in Ground reference for the device.
9 VIN2 power_in Input voltage of regulator 2; recommended input range is 2.7 V to 6 V.
10 VIN2 power_in Input voltage of regulator 2; recommended input range is 2.7 V to 6 V.
11 NC unconnected No connection; the pin is not internally connected and is listed as NC in the terminal table.
12 VOUT2 power_out Output voltage of regulator 2, rated for up to 250 mA of output current.
13 VOUT2 power_out Output voltage of regulator 2, rated for up to 250 mA of output current.
14 VSENSE2/FB2 input Regulator 2 output voltage sense for the fixed-output option or feedback input for the adjustable option; keep the connection as short as possible to avoid noise pickup.
15 RESET output Open-drain, active-low power-on reset (SVS) output indicating VOUT2 and MR1/MR2 status; it releases high-impedance after a 120 ms delay when VOUT2 exceeds 95% of its regulated voltage and requires a pull-up resistor.
16 PG1 output Open-drain power-good output that goes low when VOUT1 is below 95% of its nominal regulated voltage and goes high-impedance when VOUT1 reaches 95%; it requires a pull-up resistor.
17 VSENSE1/FB1 input Regulator 1 output voltage sense for the fixed-output option or feedback input for the adjustable option; keep the connection as short as possible to avoid noise pickup.
18 VOUT1 power_out Output voltage of regulator 1, rated for up to 500 mA of output current.
19 VOUT1 power_out Output voltage of regulator 1, rated for up to 500 mA of output current.
20 NC unconnected No connection; the pin is not internally connected and is listed as NC in the terminal table.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-20-EP
Category Power Management (PMIC)
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Reference voltage (FB connected to VO) 1.196 1.22 1.244 V 2.7V < VI < 6V, FB connected to VO; TJ = -40°C to +125°C; typ at TJ = +25°C 4
Output voltage line regulation ∆VO/VO 0.01 0.1 % VO + 1V < VI ≤ 6V 4
Quiescent current (GND current), regulator 1 and regulator 2 190 230 mA EN = 0V; VO + 1V < VI ≤ 6V; typ at TJ = +25°C 4
Output current limit, regulator 1 1.6 1.9 A VOUT = 0V 5
Output current limit, regulator 2 0.75 1 A VOUT = 0V 5
Standby current, regulator 1 I(standby) 1 3 mA EN = VI (typ at TJ = +25°C) 5
Standby current, regulator 2 I(standby) 1 3 mA EN = VI (typ at TJ = +25°C) 5
RESET trip threshold voltage 92 95 98 %VOUT VO decreasing 5
PG1 trip threshold voltage 92 95 98 %VOUT VO decreasing 5
RESET pulse duration t(RESET) 80 120 160 ms 5
VOUT2 UV comparator positive-going threshold 80 83 86 %VO 5
VOUT1 UV comparator positive-going threshold 80 83 86 %VO 6
RESET output low voltage 0.15 0.4 V VI = 3.5V, IO(RESET) = 1mA 5
PG1 output low voltage 0.15 0.4 V VI = 2.7V, IO(PG1) = 1mA 5
Minimum input voltage for valid RESET 1 1.3 V IRESET = 300mA, V(RESET) ≤ 0.8V 5
Minimum input voltage for valid PG1 1 1.3 V I(PG1) = 300mA, V(PG1) ≤ 0.8V 5
EN high level input voltage 2 V 5
EN low level input voltage 0.7 V 5
EN input current -1 1 mA 5
SEQ high level input voltage 2 V 5
SEQ low level input voltage 0.7 V 5
MR1 / MR2 high level input voltage 2 V 5
MR1 / MR2 low level input voltage 0.7 V 5
VIN1 UVLO threshold 2.4 2.65 V 6
Input voltage range (regulator 1 and 2) VI 2.7 6 V Regulator 1 and regulator 2 4
Output current, regulator 1 IO 0 500 mA 4
Output current, regulator 2 IO 0 250 mA 4
Output voltage range (adjustable option) 1.22 5.5 V 4
Operating junction temperature TJ -40 125 °C 4
Input voltage range VIN1, VIN2 -0.3 7 V Voltages tied to network ground 3
Voltage range at EN -0.3 7 V 3
Output voltage range (VOUT1, VSENSE1) 5.5 V 3
Output voltage range (VOUT2, VSENSE2) 5.5 V 3
Maximum RESET, PG1 voltage 7 V 3
Junction temperature range TJ -40 150 °C 3
Storage temperature range Tstg -65 150 °C 3
Junction-to-ambient thermal resistance θJA 74.1 °C/W PWP (20 pins), Thermal Information table 4
Junction-to-case (top) thermal resistance θJCtop 43.1 °C/W PWP (20 pins) 4
Junction-to-board thermal resistance θJB 19.7 °C/W PWP (20 pins) 4
Junction-to-top characterization parameter ψJT 2.9 °C/W PWP (20 pins) 4
Junction-to-board characterization parameter ψJB 17.3 °C/W PWP (20 pins) 4
Junction-to-case (bottom) thermal resistance θJCbot 1.4 °C/W PWP (20 pins) 4
Junction-to-ambient thermal resistance (power dissipation section) RθJA 32.6 °C/W 20-terminal PWP, no airflow 33

CAD (KiCad official)

  • Symbol: TPS70102PWP
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: tps70102pwp-etched.step / tps70102pwp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps70102pwp.step / tps70102pwp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (44 pp, sha256 d80cbe16566ccbe6, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF