← Commit history

Initial commit: component/tps65563argtr

Ray ·64b4ce9733 ·
2 files changed +265
README.mdadded+53
@@ -0,0 +1,53 @@+# TPS65563ARGTR++**Texas Instruments** · Power Management - Specialized · TQFN-16-EP(3x3)++TPS65563ARGTR from Texas Instruments, in a TQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SW | output | Primary-side power MOSFET switch output; connect to the switched side of the transformer. |+| 2 | SW | output | Primary-side power MOSFET switch output; connect to the switched side of the transformer. |+| 3 | VBAT | power_in | Battery voltage input for MOSFET OFF timing detection; input range 1.4 V to 12 V with 10-µF bypass capacitor to GND. |+| 4 | I_PEAK | input | Primary-side peak current control input; voltage at I_PEAK sets the peak current threshold into SW. |+| 5 | GND | power_in | Ground for power and IC internal circuits; connect to ground plane. |+| 6 | CHG | input | Charge enable/disable input; drive high to start charging output capacitor, low to terminate charging. |+| 7 | F_ON | input | Flash on/off input; high enables xenon flash if F_EN is high, low disables flash. |+| 8 | F_EN | input | Flash acceptable input; high permits xenon flash with F_ON high, low forces flash disable. |+| 9 | XFULL | tri_state | Charge completion indicator open-drain output; pulls low when output fully charged, high impedance during charging and fault conditions. |+| 10 | VCC | power_in | Power supply input for gate driver and IC; voltage range 2.7 V to 5.5 V with 1-µF bypass capacitor to GND. |+| 11 | IGBT_VCC | power_out | Power supply output for IGBT driver block. |+| 12 | G_IGBT_P | output | IGBT gate driver output for turn-on; output swings from GND to IGBT_VCC to drive external IGBT devices with external resistor. |+| 13 | G_IGBT_N | output | IGBT gate driver output for turn-off; output swings from IGBT_VCC to GND to drive external IGBT devices with external resistor. |+| 14 | GND | power_in | Ground for power and IC internal circuits; connect to ground plane. |+| 15 | GND | power_in | Ground for power and IC internal circuits; connect to ground plane. |+| 16 | TEST_GND | power_in | Test ground used by TI for manufacturing; should be connected to GND and ground plane. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TQFN-16-EP(3x3) |+| Category | Power Management (PMIC) |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `TPS65563ARGTR`+- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`+- 3D model: TQFN-16-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `tps65563argtr-etched.step` / `tps65563argtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps65563argtr.step` / `tps65563argtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps65563a.pdf) (19 pp, sha256 `59ee3fba0d7dece2`, retrieved 2026-09-26, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps65563argtr-datasheet.pdf)
page.jsonadded+212
@@ -0,0 +1,212 @@+{+  "slug": "tps65563argtr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Power Management - Specialized, TQFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps65563argtr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps65563argtr.kicad_sym",+    "tps65563argtr.kicad_mod",+    "tps65563argtr.glb",+    "tps65563argtr.step",+    "tps65563argtr.lbr",+    "docs/hero.png",+    "docs/tps65563argtr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS65563ARGTR",+    "manufacturer": "Texas Instruments",+    "package": "TQFN-16-EP(3x3)",+    "pin_count": 17,+    "category": "Power Management (PMIC)",+    "subcategory": "Power Management - Specialized",+    "datasheet": "https://www.ti.com/lit/ds/symlink/tps65563a.pdf",+    "parts": {+      "symbol": "tps65563argtr.kicad_sym",+      "footprint": "tps65563argtr.kicad_mod",+      "model_3d": "tps65563argtr-etched.glb",+      "model_3d_plain": "tps65563argtr.glb",+      "model_3d_step": "tps65563argtr-etched.step",+      "model_3d_step_plain": "tps65563argtr.step",+      "lbr": "tps65563argtr.lbr"+    },+    "distributor_links": {+      "lcsc": "C2156018",+      "digikey": "296-23687-2-ND",+      "mouser": "595-TPS65563ARGTR"+    },+    "distributor_check": {+      "checked_at": "2026-09-26T18:56:41Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-23687-2-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-TPS65563ARGTR",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "SW",+        "type": "output",+        "description": "Primary-side power MOSFET switch output; connect to the switched side of the transformer."+      },+      {+        "number": "2",+        "name": "SW",+        "type": "output",+        "description": "Primary-side power MOSFET switch output; connect to the switched side of the transformer."+      },+      {+        "number": "3",+        "name": "VBAT",+        "type": "power_in",+        "description": "Battery voltage input for MOSFET OFF timing detection; input range 1.4 V to 12 V with 10-µF bypass capacitor to GND."+      },+      {+        "number": "4",+        "name": "I_PEAK",+        "type": "input",+        "description": "Primary-side peak current control input; voltage at I_PEAK sets the peak current threshold into SW."+      },+      {+        "number": "5",+        "name": "GND",+        "type": "power_in",+        "description": "Ground for power and IC internal circuits; connect to ground plane."+      },+      {+        "number": "6",+        "name": "CHG",+        "type": "input",+        "description": "Charge enable/disable input; drive high to start charging output capacitor, low to terminate charging."+      },+      {+        "number": "7",+        "name": "F_ON",+        "type": "input",+        "description": "Flash on/off input; high enables xenon flash if F_EN is high, low disables flash."+      },+      {+        "number": "8",+        "name": "F_EN",+        "type": "input",+        "description": "Flash acceptable input; high permits xenon flash with F_ON high, low forces flash disable."+      },+      {+        "number": "9",+        "name": "XFULL",+        "type": "tri_state",+        "description": "Charge completion indicator open-drain output; pulls low when output fully charged, high impedance during charging and fault conditions."+      },+      {+        "number": "10",+        "name": "VCC",+        "type": "power_in",+        "description": "Power supply input for gate driver and IC; voltage range 2.7 V to 5.5 V with 1-µF bypass capacitor to GND."+      },+      {+        "number": "11",+        "name": "IGBT_VCC",+        "type": "power_out",+        "description": "Power supply output for IGBT driver block."+      },+      {+        "number": "12",+        "name": "G_IGBT_P",+        "type": "output",+        "description": "IGBT gate driver output for turn-on; output swings from GND to IGBT_VCC to drive external IGBT devices with external resistor."+      },+      {+        "number": "13",+        "name": "G_IGBT_N",+        "type": "output",+        "description": "IGBT gate driver output for turn-off; output swings from IGBT_VCC to GND to drive external IGBT devices with external resistor."+      },+      {+        "number": "14",+        "name": "GND",+        "type": "power_in",+        "description": "Ground for power and IC internal circuits; connect to ground plane."+      },+      {+        "number": "15",+        "name": "GND",+        "type": "power_in",+        "description": "Ground for power and IC internal circuits; connect to ground plane."+      },+      {+        "number": "16",+        "name": "TEST_GND",+        "type": "power_in",+        "description": "Test ground used by TI for manufacturing; should be connected to GND and ground plane."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 17 added from the footprint"+        ],+        "pages_sent": 19,+        "cost_usd": 0.2477,+        "at": "2026-09-26T18:56:23"+      },+      "datasheet": {+        "url": "https://www.ti.com/lit/ds/symlink/tps65563a.pdf",+        "pages": 19,+        "sha256": "59ee3fba0d7dece2",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file