← Commit history

Initial commit: component/tps65283rger

Ray ·ad3c5a747b ·
2 files changed +322
README.mdadded+62
@@ -0,0 +1,62 @@+# TPS65283RGER++**Texas Instruments** · DC-DC Converters · VQFN-24-EP(4x4)++TPS65283RGER from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PGOOD2 | output | Power good indicator for buck2; asserts low when output voltage is out of regulation due to thermal shutdown, dropout, overvoltage, disabled, or during soft start. |+| 2 | EN1 | input | Enable pin for buck1; high signal enables converter, optional ceramic capacitor provides delayed startup. |+| 3 | EN2 | input | Enable pin for buck2; high signal enables converter, optional ceramic capacitor provides delayed startup. |+| 4 | ROSC/SYNC | input | Programmable oscillator frequency from 200 kHz to 2 MHz via external resistor or external clock synchronization input. |+| 5 | SW_EN | input | Enable input for power switch; float to enable. |+| 6 | nFAULT | output | Active-low open-drain output; asserted low during power switch overcurrent or reverse-voltage condition. |+| 7 | SW_OUT | power_out | Power switch output node. |+| 8 | SW_IN | power_in | Power switch input node; input voltage range 2.4 V to 6 V. |+| 9 | VIN2 | power_in | Input power supply for buck2; connect with 10 µF ceramic capacitor as close as possible to pin. |+| 10 | PGND2 | power_in | Power ground connection for buck2; connect as close as possible to negative terminal of input capacitor. |+| 11 | LX2 | output | Switching node for buck2; voltage swings from diode drop below ground to buck2 input voltage. |+| 12 | BST2 | passive | Bootstrap supply for buck2 high-side gate driver; connect 47 nF ceramic capacitor from this pin to LX2. |+| 13 | COMP2 | output | Error amplifier output and compensation pin for buck2; connect series resistor and capacitor for control loop compensation. |+| 14 | FB2 | input | Feedback sensing pin for buck2 output voltage; feedback reference voltage 0.6 V ±1%, connect to resistor divider network. |+| 15 | RSET | input | Power switch current limit programming pin; external resistor sets current limit threshold, recommended range 9.1 kΩ to 80.6 kΩ. |+| 16 | AGND | power_in | Analog ground common to buck and power switch controllers; route separately from power grounds to V7V bypass capacitor negative terminal. |+| 17 | FB1 | input | Feedback sensing pin for buck1 output voltage; feedback reference voltage 0.6 V ±1%, connect to resistor divider network. |+| 18 | COMP1 | output | Error amplifier output and compensation pin for buck1; connect series resistor and capacitor for control loop compensation. |+| 19 | BST1 | passive | Bootstrap supply for buck1 high-side gate driver; connect 47 nF ceramic capacitor from this pin to LX1. |+| 20 | LX1 | output | Switching node for buck1; voltage swings from diode drop below ground to buck1 input voltage. |+| 21 | PGND1 | power_in | Power ground connection for buck1; connect as close as possible to negative terminal of input capacitor. |+| 22 | VIN1 | power_in | Input power supply for buck1 and internal analog bias circuits; connect with 10 µF ceramic capacitor as close as possible to pin. |+| 23 | V7V | power_out | Internal linear regulator output at typical 6.3 V for gate drivers and internal circuits; minimum 1 µF ceramic capacitor required for decoupling. |+| 24 | PGOOD1 | output | Power good indicator for buck1; asserts low when output voltage is out of regulation due to thermal shutdown, dropout, overvoltage, disabled, or during soft start. |+| 25 | PowerPAD | power_in | Exposed thermal pad underneath IC package; connect to power ground with multiple vias for thermal dissipation, no internal signal connection. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-24-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `TPS65283RGER`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm`+- 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `tps65283rger-etched.step` / `tps65283rger-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps65283rger.step` / `tps65283rger.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps65283-1) (43 pp, sha256 `eb69c587d9ca6697`, retrieved 2026-09-25, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps65283rger-datasheet.pdf)
page.jsonadded+260
@@ -0,0 +1,260 @@+{+  "slug": "tps65283rger",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, VQFN-24-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps65283rger",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps65283rger.kicad_sym",+    "tps65283rger.kicad_mod",+    "tps65283rger.glb",+    "tps65283rger.step",+    "tps65283rger.lbr",+    "docs/hero.png",+    "docs/tps65283rger-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS65283RGER",+    "manufacturer": "Texas Instruments",+    "package": "VQFN-24-EP(4x4)",+    "pin_count": 25,+    "category": "Power Management (PMIC)",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps65283-1",+    "parts": {+      "symbol": "tps65283rger.kicad_sym",+      "footprint": "tps65283rger.kicad_mod",+      "model_3d": "tps65283rger-etched.glb",+      "model_3d_plain": "tps65283rger.glb",+      "model_3d_step": "tps65283rger-etched.step",+      "model_3d_step_plain": "tps65283rger.step",+      "lbr": "tps65283rger.lbr"+    },+    "distributor_links": {+      "lcsc": "C702326",+      "digikey": "TPS65283RGER-ND",+      "mouser": "595-TPS65283RGER"+    },+    "distributor_check": {+      "checked_at": "2026-09-25T14:07:54Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "TPS65283RGER-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-TPS65283RGER",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "PGOOD2",+        "type": "output",+        "description": "Power good indicator for buck2; asserts low when output voltage is out of regulation due to thermal shutdown, dropout, overvoltage, disabled, or during soft start."+      },+      {+        "number": "2",+        "name": "EN1",+        "type": "input",+        "description": "Enable pin for buck1; high signal enables converter, optional ceramic capacitor provides delayed startup."+      },+      {+        "number": "3",+        "name": "EN2",+        "type": "input",+        "description": "Enable pin for buck2; high signal enables converter, optional ceramic capacitor provides delayed startup."+      },+      {+        "number": "4",+        "name": "ROSC/SYNC",+        "type": "input",+        "description": "Programmable oscillator frequency from 200 kHz to 2 MHz via external resistor or external clock synchronization input."+      },+      {+        "number": "5",+        "name": "SW_EN",+        "type": "input",+        "description": "Enable input for power switch; float to enable."+      },+      {+        "number": "6",+        "name": "nFAULT",+        "type": "output",+        "description": "Active-low open-drain output; asserted low during power switch overcurrent or reverse-voltage condition."+      },+      {+        "number": "7",+        "name": "SW_OUT",+        "type": "power_out",+        "description": "Power switch output node."+      },+      {+        "number": "8",+        "name": "SW_IN",+        "type": "power_in",+        "description": "Power switch input node; input voltage range 2.4 V to 6 V."+      },+      {+        "number": "9",+        "name": "VIN2",+        "type": "power_in",+        "description": "Input power supply for buck2; connect with 10 µF ceramic capacitor as close as possible to pin."+      },+      {+        "number": "10",+        "name": "PGND2",+        "type": "power_in",+        "description": "Power ground connection for buck2; connect as close as possible to negative terminal of input capacitor."+      },+      {+        "number": "11",+        "name": "LX2",+        "type": "output",+        "description": "Switching node for buck2; voltage swings from diode drop below ground to buck2 input voltage."+      },+      {+        "number": "12",+        "name": "BST2",+        "type": "passive",+        "description": "Bootstrap supply for buck2 high-side gate driver; connect 47 nF ceramic capacitor from this pin to LX2."+      },+      {+        "number": "13",+        "name": "COMP2",+        "type": "output",+        "description": "Error amplifier output and compensation pin for buck2; connect series resistor and capacitor for control loop compensation."+      },+      {+        "number": "14",+        "name": "FB2",+        "type": "input",+        "description": "Feedback sensing pin for buck2 output voltage; feedback reference voltage 0.6 V ±1%, connect to resistor divider network."+      },+      {+        "number": "15",+        "name": "RSET",+        "type": "input",+        "description": "Power switch current limit programming pin; external resistor sets current limit threshold, recommended range 9.1 kΩ to 80.6 kΩ."+      },+      {+        "number": "16",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground common to buck and power switch controllers; route separately from power grounds to V7V bypass capacitor negative terminal."+      },+      {+        "number": "17",+        "name": "FB1",+        "type": "input",+        "description": "Feedback sensing pin for buck1 output voltage; feedback reference voltage 0.6 V ±1%, connect to resistor divider network."+      },+      {+        "number": "18",+        "name": "COMP1",+        "type": "output",+        "description": "Error amplifier output and compensation pin for buck1; connect series resistor and capacitor for control loop compensation."+      },+      {+        "number": "19",+        "name": "BST1",+        "type": "passive",+        "description": "Bootstrap supply for buck1 high-side gate driver; connect 47 nF ceramic capacitor from this pin to LX1."+      },+      {+        "number": "20",+        "name": "LX1",+        "type": "output",+        "description": "Switching node for buck1; voltage swings from diode drop below ground to buck1 input voltage."+      },+      {+        "number": "21",+        "name": "PGND1",+        "type": "power_in",+        "description": "Power ground connection for buck1; connect as close as possible to negative terminal of input capacitor."+      },+      {+        "number": "22",+        "name": "VIN1",+        "type": "power_in",+        "description": "Input power supply for buck1 and internal analog bias circuits; connect with 10 µF ceramic capacitor as close as possible to pin."+      },+      {+        "number": "23",+        "name": "V7V",+        "type": "power_out",+        "description": "Internal linear regulator output at typical 6.3 V for gate drivers and internal circuits; minimum 1 µF ceramic capacitor required for decoupling."+      },+      {+        "number": "24",+        "name": "PGOOD1",+        "type": "output",+        "description": "Power good indicator for buck1; asserts low when output voltage is out of regulation due to thermal shutdown, dropout, overvoltage, disabled, or during soft start."+      },+      {+        "number": "25",+        "name": "PowerPAD",+        "type": "power_in",+        "description": "Exposed thermal pad underneath IC package; connect to power ground with multiple vias for thermal dissipation, no internal signal connection."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Thermal pad (pin 25) is listed in Pin Functions as 'PowerPAD —' without explicit numbering in specif"+        ],+        "pages_sent": 43,+        "cost_usd": 0.4869,+        "at": "2026-09-25T14:07:35"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps65283-1",+        "pages": 43,+        "sha256": "eb69c587d9ca6697",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file