← Commit history

Initial commit: component/tps65261rhbr

Ray ·9fd3226e65 ·
2 files changed +363
README.mdadded+70
@@ -0,0 +1,70 @@+# TPS65261RHBR++**Texas Instruments** · DC-DC Converters · VQFN-32-EP(5x5)++TPS65261RHBR from Texas Instruments, in a VQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | EN3 | input | Enable pin for buck3; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V |+| 2 | PGOOD | output | Open-drain power good output; asserts low when any buck output is out of regulation (±2.5%), thermal shutdown active, overcurrent condition exists, or enable pin low; max sink 1mA at 0.4V |+| 3 | RESET | output | Open-drain power failure output signal; asserts low when VDIV input drops below 1.23V threshold for power failure detection; deglitch time 12-16 cycles |+| 4 | MODE | input | Mode select input; when high, enables automatic power-up/power-down sequencing based on EN1/EN2/EN3 states; when low, enables independent enable pin control; operating range -0.1V to 6.3V |+| 5 | V7V | power_out | Internal LDO output supplying gate drivers and internal logic; 6.3V typical (6.0V to 6.6V range), maximum current 175mA; requires 10µF ceramic capacitor to power ground |+| 6 | FB2 | input | Feedback Kelvin sensing pin for buck2 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V |+| 7 | COMP2 | output | Error amplifier output for buck2 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V |+| 8 | SS2 | input | Soft-start and tracking input for buck2 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V |+| 9 | BST2 | power_in | Bootstrap supply for buck2 high-side gate driver; connect 47nF ceramic capacitor between BST2 and LX2 pins; operating range -0.3V to 7V referenced to LX2 |+| 10 | LX2 | output | Buck2 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN2 voltage (maximum 18V); high di/dt node requiring careful PCB layout |+| 11 | PGND2 | power_in | Buck2 power ground connection; connect as close as practical to negative terminal of PVIN2 input ceramic capacitor to minimize inductance |+| 12 | PVIN2 | power_in | Buck2 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path |+| 13 | PVIN3 | power_in | Buck3 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path |+| 14 | PGND3 | power_in | Buck3 power ground connection; connect as close as practical to negative terminal of PVIN3 input ceramic capacitor to minimize inductance |+| 15 | LX3 | output | Buck3 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN3 voltage (maximum 18V); high di/dt node requiring careful PCB layout |+| 16 | BST3 | power_in | Bootstrap supply for buck3 high-side gate driver; connect 47nF ceramic capacitor between BST3 and LX3 pins; operating range -0.3V to 7V referenced to LX3 |+| 17 | SS3 | input | Soft-start and tracking input for buck3 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V |+| 18 | COMP3 | output | Error amplifier output for buck3 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V |+| 19 | FB3 | input | Feedback Kelvin sensing pin for buck3 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V |+| 20 | ROSC | input | Oscillator frequency programmable pin; connect external resistor to ground to set switching frequency from 250kHz to 2MHz; operating range -0.1V to 3V |+| 21 | AGND | power_in | Analog ground for buck controllers and analog signal circuits; route separately from high current power grounds to negative terminal of VIN bypass capacitor to minimize noise coupling |+| 22 | FB1 | input | Feedback Kelvin sensing pin for buck1 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V |+| 23 | COMP1 | output | Error amplifier output for buck1 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V |+| 24 | SS1 | input | Soft-start and tracking input for buck1 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V |+| 25 | BST1 | power_in | Bootstrap supply for buck1 high-side gate driver; connect 47nF ceramic capacitor between BST1 and LX1 pins; operating range -0.3V to 7V referenced to LX1 |+| 26 | LX1 | output | Buck1 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN1 voltage (maximum 18V); high di/dt node requiring careful PCB layout and 180° phase shift from buck2/3 clocks |+| 27 | PGND1 | power_in | Buck1 power ground connection; connect as close as practical to negative terminal of PVIN1 input ceramic capacitor to minimize inductance |+| 28 | PVIN1 | power_in | Buck1 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path |+| 29 | VIN | power_in | Buck controller power supply for internal logic and bias circuits; operating range 4.5V to 18V; UVLO thresholds: rising 4.25V typical, falling 3.75V typical, hysteresis 500mV |+| 30 | VDIV | input | Input voltage threshold for power failure detection; external resistor divider sets detection threshold to 1.23V typical; 1µA pullup current provides threshold hysteresis; operating range -0.1V to 6.3V |+| 31 | EN1 | input | Enable pin for buck1; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V |+| 32 | EN2 | input | Enable pin for buck2; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V |+| 33 | Thermal Pad | passive | Exposed thermal pad for junction-to-board heat dissipation; no internal electrical wire bond to die; must be soldered to PCB ground plane for optimal thermal performance |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-32-EP(5x5) |+| Category | Power Management (PMIC) |+| Pins | 33 |++## CAD (KiCad official)++- Symbol: `TPS65261RHBR`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: VQFN-32-EP(5x5) (KiCad packages3D, STEP)+- 3D model files: `tps65261rhbr-etched.step` / `tps65261rhbr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps65261rhbr.step` / `tps65261rhbr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps65261) (48 pp, sha256 `304396ee72bd117c`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps65261rhbr-datasheet.pdf)
page.jsonadded+293
@@ -0,0 +1,293 @@+{+  "slug": "tps65261rhbr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, VQFN-32-EP(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps65261rhbr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps65261rhbr.kicad_sym",+    "tps65261rhbr.kicad_mod",+    "tps65261rhbr.glb",+    "tps65261rhbr.step",+    "tps65261rhbr.lbr",+    "docs/hero.png",+    "docs/tps65261rhbr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS65261RHBR",+    "manufacturer": "Texas Instruments",+    "package": "VQFN-32-EP(5x5)",+    "pin_count": 33,+    "category": "Power Management (PMIC)",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps65261",+    "parts": {+      "symbol": "tps65261rhbr.kicad_sym",+      "footprint": "tps65261rhbr.kicad_mod",+      "model_3d": "tps65261rhbr-etched.glb",+      "model_3d_plain": "tps65261rhbr.glb",+      "model_3d_step": "tps65261rhbr-etched.step",+      "model_3d_step_plain": "tps65261rhbr.step",+      "lbr": "tps65261rhbr.lbr"+    },+    "distributor_links": {+      "lcsc": "C138722"+    },+    "pins": [+      {+        "number": "1",+        "name": "EN3",+        "type": "input",+        "description": "Enable pin for buck3; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V"+      },+      {+        "number": "2",+        "name": "PGOOD",+        "type": "output",+        "description": "Open-drain power good output; asserts low when any buck output is out of regulation (±2.5%), thermal shutdown active, overcurrent condition exists, or enable pin low; max sink 1mA at 0.4V"+      },+      {+        "number": "3",+        "name": "RESET",+        "type": "output",+        "description": "Open-drain power failure output signal; asserts low when VDIV input drops below 1.23V threshold for power failure detection; deglitch time 12-16 cycles"+      },+      {+        "number": "4",+        "name": "MODE",+        "type": "input",+        "description": "Mode select input; when high, enables automatic power-up/power-down sequencing based on EN1/EN2/EN3 states; when low, enables independent enable pin control; operating range -0.1V to 6.3V"+      },+      {+        "number": "5",+        "name": "V7V",+        "type": "power_out",+        "description": "Internal LDO output supplying gate drivers and internal logic; 6.3V typical (6.0V to 6.6V range), maximum current 175mA; requires 10µF ceramic capacitor to power ground"+      },+      {+        "number": "6",+        "name": "FB2",+        "type": "input",+        "description": "Feedback Kelvin sensing pin for buck2 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V"+      },+      {+        "number": "7",+        "name": "COMP2",+        "type": "output",+        "description": "Error amplifier output for buck2 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V"+      },+      {+        "number": "8",+        "name": "SS2",+        "type": "input",+        "description": "Soft-start and tracking input for buck2 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V"+      },+      {+        "number": "9",+        "name": "BST2",+        "type": "power_in",+        "description": "Bootstrap supply for buck2 high-side gate driver; connect 47nF ceramic capacitor between BST2 and LX2 pins; operating range -0.3V to 7V referenced to LX2"+      },+      {+        "number": "10",+        "name": "LX2",+        "type": "output",+        "description": "Buck2 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN2 voltage (maximum 18V); high di/dt node requiring careful PCB layout"+      },+      {+        "number": "11",+        "name": "PGND2",+        "type": "power_in",+        "description": "Buck2 power ground connection; connect as close as practical to negative terminal of PVIN2 input ceramic capacitor to minimize inductance"+      },+      {+        "number": "12",+        "name": "PVIN2",+        "type": "power_in",+        "description": "Buck2 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path"+      },+      {+        "number": "13",+        "name": "PVIN3",+        "type": "power_in",+        "description": "Buck3 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path"+      },+      {+        "number": "14",+        "name": "PGND3",+        "type": "power_in",+        "description": "Buck3 power ground connection; connect as close as practical to negative terminal of PVIN3 input ceramic capacitor to minimize inductance"+      },+      {+        "number": "15",+        "name": "LX3",+        "type": "output",+        "description": "Buck3 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN3 voltage (maximum 18V); high di/dt node requiring careful PCB layout"+      },+      {+        "number": "16",+        "name": "BST3",+        "type": "power_in",+        "description": "Bootstrap supply for buck3 high-side gate driver; connect 47nF ceramic capacitor between BST3 and LX3 pins; operating range -0.3V to 7V referenced to LX3"+      },+      {+        "number": "17",+        "name": "SS3",+        "type": "input",+        "description": "Soft-start and tracking input for buck3 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V"+      },+      {+        "number": "18",+        "name": "COMP3",+        "type": "output",+        "description": "Error amplifier output for buck3 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V"+      },+      {+        "number": "19",+        "name": "FB3",+        "type": "input",+        "description": "Feedback Kelvin sensing pin for buck3 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V"+      },+      {+        "number": "20",+        "name": "ROSC",+        "type": "input",+        "description": "Oscillator frequency programmable pin; connect external resistor to ground to set switching frequency from 250kHz to 2MHz; operating range -0.1V to 3V"+      },+      {+        "number": "21",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground for buck controllers and analog signal circuits; route separately from high current power grounds to negative terminal of VIN bypass capacitor to minimize noise coupling"+      },+      {+        "number": "22",+        "name": "FB1",+        "type": "input",+        "description": "Feedback Kelvin sensing pin for buck1 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V"+      },+      {+        "number": "23",+        "name": "COMP1",+        "type": "output",+        "description": "Error amplifier output for buck1 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V"+      },+      {+        "number": "24",+        "name": "SS1",+        "type": "input",+        "description": "Soft-start and tracking input for buck1 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V"+      },+      {+        "number": "25",+        "name": "BST1",+        "type": "power_in",+        "description": "Bootstrap supply for buck1 high-side gate driver; connect 47nF ceramic capacitor between BST1 and LX1 pins; operating range -0.3V to 7V referenced to LX1"+      },+      {+        "number": "26",+        "name": "LX1",+        "type": "output",+        "description": "Buck1 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN1 voltage (maximum 18V); high di/dt node requiring careful PCB layout and 180° phase shift from buck2/3 clocks"+      },+      {+        "number": "27",+        "name": "PGND1",+        "type": "power_in",+        "description": "Buck1 power ground connection; connect as close as practical to negative terminal of PVIN1 input ceramic capacitor to minimize inductance"+      },+      {+        "number": "28",+        "name": "PVIN1",+        "type": "power_in",+        "description": "Buck1 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path"+      },+      {+        "number": "29",+        "name": "VIN",+        "type": "power_in",+        "description": "Buck controller power supply for internal logic and bias circuits; operating range 4.5V to 18V; UVLO thresholds: rising 4.25V typical, falling 3.75V typical, hysteresis 500mV"+      },+      {+        "number": "30",+        "name": "VDIV",+        "type": "input",+        "description": "Input voltage threshold for power failure detection; external resistor divider sets detection threshold to 1.23V typical; 1µA pullup current provides threshold hysteresis; operating range -0.1V to 6.3V"+      },+      {+        "number": "31",+        "name": "EN1",+        "type": "input",+        "description": "Enable pin for buck1; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V"+      },+      {+        "number": "32",+        "name": "EN2",+        "type": "input",+        "description": "Enable pin for buck2; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V"+      },+      {+        "number": "33",+        "name": "Thermal Pad",+        "type": "passive",+        "description": "Exposed thermal pad for junction-to-board heat dissipation; no internal electrical wire bond to die; must be soldered to PCB ground plane for optimal thermal performance"+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "1/33 pins cited to the wrong page (name found elsewhere): ['33:Thermal Pad@p4']"+        ],+        "pages_sent": 48,+        "cost_usd": 0.5037,+        "at": "2026-09-23T08:28:44"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps65261",+        "pages": 48,+        "sha256": "304396ee72bd117c",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 33,+        "described": 33,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file