main
Ray
Publish 0.1.0
0448bee
TPS65023BRSBR
Texas Instruments · Battery Management ICs · WQFN-40-EP(5x5)
TPS65023BRSBR from Texas Instruments, in a WQFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DEFDCDC3 | input | Input signal indicating default VDCDC3 voltage, 0 = 1.8 V, 1 = 3.3 V, or connect to a resistor divider between VDCDC3 and GND for an output set from 0.6 V to VINDCDC3. |
| 2 | VDCDC3 | input | VDCDC3 feedback voltage sense input, connect directly to VDCDC3. |
| 3 | PGND3 | power_in | Power ground for VDCDC3 converter. |
| 4 | L3 | output | Switch pin of VDCDC3 converter, where the VDCDC3 inductor is connected. |
| 5 | VINDCDC3 | power_in | Input voltage for VDCDC3 step-down converter, must be connected to the same supply as VINDCDC1, VINDCDC2 and VCC. |
| 6 | VINDCDC1 | power_in | Input voltage for VDCDC1 step-down converter, must be connected to the same supply as VINDCDC2, VINDCDC3 and VCC. |
| 7 | L1 | output | Switch pin of VDCDC1 converter, where the VDCDC1 inductor is connected. |
| 8 | PGND1 | power_in | Power ground for VDCDC1 converter. |
| 9 | VDCDC1 | input | VDCDC1 feedback voltage sense input, connect directly to VDCDC1. |
| 10 | DEFDCDC1 | input | Input signal indicating default VDCDC1 voltage, 0 = 1.2 V, 1 = 1.6 V, or connect to a resistor divider between VDCDC1 and GND for an output set from 0.6 V to VINDCDC1. |
| 11 | HOT_RESET | input | Push button input that reboots or wakes up the processor through the RESPWRON output pin. |
| 12 | DEFLDO1 | input | Digital input that sets the default output voltage of LDO1 and LDO2. |
| 13 | DEFLDO2 | input | Digital input that sets the default output voltage of LDO1 and LDO2. |
| 14 | VSYSIN | power_in | Input of system voltage for the VRTC switch. |
| 15 | VBACKUP | power_in | Connect the backup battery to this input pin. |
| 16 | VRTC | power_out | Output voltage of the LDO and switch for the real time clock. |
| 17 | AGND2 | power_in | Analog ground, all analog ground pins are connected internally on the chip. |
| 18 | VLDO2 | power_out | Output voltage of LDO2. |
| 19 | VINLDO | power_in | Input voltage for LDO1 and LDO2. |
| 20 | VLDO1 | power_out | Output voltage of LDO1. |
| 21 | LOWBAT | output | Open-drain output of the LOW_BAT comparator. |
| 22 | LDO_EN | input | Enable input for LDO1 and LDO2, logic high enables the LDOs and logic low disables them. |
| 23 | DCDC3_EN | input | VDCDC3 enable pin, logic high enables the regulator and logic low disables it. |
| 24 | DCDC2_EN | input | VDCDC2 enable pin, logic high enables the regulator and logic low disables it. |
| 25 | DCDC1_EN | input | VDCDC1 enable pin, logic high enables the regulator and logic low disables it. |
| 26 | TRESPWRON | input | Connect the timing capacitor here to set the reset delay time, 1 nF gives 100 ms. |
| 27 | RESPWRON | output | Open-drain system reset output. |
| 28 | INT | output | Open-drain output. |
| 29 | SDAT | bidirectional | Serial interface data and address. |
| 30 | SCLK | input | Serial interface clock line. |
| 31 | PWRFAIL | output | Open-drain output, active low when the PWRFAIL comparator indicates a low VBAT condition. |
| 32 | DEFDCDC2 | input | Input signal indicating default VDCDC2 voltage, 0 = 1.8 V, 1 = 3.3 V, or connect to a resistor divider between VDCDC2 and GND for an output set from 0.6 V to VINDCDC2. |
| 33 | VDCDC2 | input | VDCDC2 feedback voltage sense input, connect directly to VDCDC2. |
| 34 | PGND2 | power_in | Power ground for VDCDC2 converter. |
| 35 | L2 | output | Switch pin of VDCDC2 converter, where the VDCDC2 inductor is connected. |
| 36 | VINDCDC2 | power_in | Input voltage for VDCDC2 step-down converter, must be connected to the same supply as VINDCDC1, VINDCDC3 and VCC. |
| 37 | VCC | power_in | Power supply for digital and analog circuitry of the three DC-DC converters and the serial interface, must be connected to the same supply as VINDCDC1, VINDCDC2 and VINDCDC3. |
| 38 | PWRFAIL_SNS | input | Input for the comparator driving the PWRFAIL output. |
| 39 | LOWBAT_SNS | input | Input for the comparator driving the LOW_BAT output. |
| 40 | AGND1 | power_in | Analog ground, all analog ground pins are connected internally on the chip. |
| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-40-EP(5x5) |
| Category | Power Supply Chip |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage on all pins except AGND and PGND, wrt AGND | VI | -0.3 | 7 | V | over operating free-air temperature range | 7 | |
| Current at VINDCDCx, Lx, PGNDx | 2000 | mA | 7 | ||||
| Peak current at all other pins | 1000 | mA | 7 | ||||
| Operating free-air temperature (abs max table) | TA | -40 | 85 | °C | 7 | ||
| Maximum junction temperature | TJ | 125 | °C | 7 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 7 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | ANSI/ESDA/JEDEC JS-001 | 7 | |
| ESD CDM | V(ESD) | -500 | 500 | V | JESD22-C101 | 7 | |
| Input voltage step-down converters | VCC | 2.5 | 6 | V | VINDCDC1, VINDCDC2, VINDCDC3 tied to same rail | 7 | |
| Output voltage VDCDC1 | VO | 0.6 | 6 | V | max printed as VINDCDC1; 6 V is the VINDCDC1 maximum | 7 | |
| Input voltage for LDOs | VI | 1.5 | 6.5 | V | VINLDO1, VINLDO2 | 7 | |
| Output voltage for LDOs | VO | 1 | V | max printed as VINLDO1-2 | 7 | ||
| Output current at L1 | IO(DCDC1) | 1700 | mA | 7 | |||
| Output current at L2 | IO(DCDC2) | 1200 | mA | 7 | |||
| Output current at L3 | IO(DCDC3) | 1000 | mA | 7 | |||
| Inductor at L1/L2/L3 | 1.5 | 2.2 | μH | 7 | |||
| Output capacitor at VDCDC1/2/3 | CO | 10 | 22 | μF | 7 | ||
| Input capacitor at VINDCDCx | CI | 10 | μF | 7 | |||
| Output current at VLDO1, VLDO2 | IO(VLDO1-2) | 200 | mA | 8 | |||
| Output capacitor at VRTC | CO(VRTC) | 4.7 | μF | 8 | |||
| Operating ambient temperature | TA | -40 | 85 | °C | 8 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 8 | ||
| Resistor from VINDCDCx to VCC for filtering | 1 | 10 | Ω | 8 | |||
| Junction-to-ambient thermal resistance | RθJA | 32.7 | °C/W | RSB (WQFN) 40 pins | 8 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 15.3 | °C/W | 8 | |||
| Junction-to-board thermal resistance | RθJB | 13.6 | °C/W | 8 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.1 | °C/W | 8 | |||
| High level input voltage for SCLK pin (TPS65023B) | VIH | 1.4 | V | Rpullup at SCLK = 4.7 kΩ, pulled to VRTC; VCC = 2.5 V to 5.25 V | 8 | ||
| High level input voltage for SDAT pin (TPS65023B) | VIH | 1.69 | V | Rpullup at SDAT = 4.7 kΩ, pulled to VRTC; VCC = 2.5 V to 5.25 V | 8 | ||
| High level input voltage for SDAT pin (TPS65023B) | VIH | 1.55 | V | Rpullup at SDAT = 4.7 kΩ, pulled to VRTC; VCC = 2.5 V to 4.5 V | 8 | ||
| Low level input voltage SCLK/SDAT (TPS65023B) | VIL | 0 | 0.35 | V | Rpullup at SCLK and SDAT = 4.7 kΩ, pulled to VRTC | 8 | |
| Input bias current SCLK/SDAT | IH | 0.01 | 0.1 | μA | 8 | ||
| High-level input voltage (HOT_RESET, ENs, DEFLDOx) | VIH | 1.3 | V | max printed as VCC | 8 | ||
| Low-level input voltage (HOT_RESET, ENs, DEFLDOx) | VIL | 0 | 0.4 | V | 8 | ||
| Deglitch time at HOT_RESET | tdeglitch | 25 | 30 | 35 | ms | 8 | |
| Low-level output voltage | VOL | 0 | 0.3 | V | IIL = 5 mA | 9 | |
| Internal charge/discharge current on TRESPWRON | ICONST | 1.7 | 2 | 2.3 | μA | Used for generating RESPWRON delay | 9 |
| TRESPWRON lower comparator threshold | TRESPWRON_LOWTH | 0.225 | 0.25 | 0.275 | V | Used for generating RESPWRON delay | 9 |
| TRESPWRON upper comparator threshold | TRESPWRON_UPTH | 0.97 | 1 | 1.103 | V | Used for generating RESPWRON delay | 9 |
| LDO1/LDO2 output voltage accuracy | -2 | 1 | % | IO = 10 mA | 9 | ||
| LDO1/LDO2 dropout | 65 | 150 | mV | IO = 50 mA, VINLDO = 1.5 V | 9 | ||
| LDO1/LDO2 line regulation | -1 | 1 | % | VINLDO1,2 = VLDO1,2 + 0.5 V (min. 2.5 V) to 6.5 V, IO = 10 mA | 9 | ||
| LDO1/LDO2 load regulation | -1 | 1 | % | IO = 0 mA to 50 mA | 9 | ||
| Thermal shutdown | T(SD) | 160 | °C | Increasing junction temperature | 9 | ||
| Internal UVLO | UVLO | -2 | 2.35 | 2 | V | VCC falling; tolerance in % | 9 |
| Voltage detector comparator threshold | -1 | 1 | 1 | V | Falling threshold; tolerance in % | 9 | |
| Power-good falling threshold | V(PGOODF) | -12 | -10 | -8 | % | VDCDC1-3, VLDO1, VLDO2, decreasing | 9 |
| Operating quiescent current, PFM | I(q) | 85 | 100 | μA | All 3 DCDC converters enabled, zero load, no switching, LDOs enabled; VCC = 3.6 V, VBACKUP = 3 V; V(VSYSIN) = 0 V | 10 | |
| Quiescent current, all converters disabled | I(q) | 23 | 33 | μA | All converters disabled, LDOs off; VCC = 3.6 V, VBACKUP = 3 V; V(VSYSIN) = 0 V | 10 | |
| Current into VCC, PWM | II | 2 | 3 | mA | All 3 DCDC converters enabled and running in PWM, LDOs off; VCC = 3.6 V | 10 | |
| VRTC output current | IO | 30 | mA | VSYSIN < 2.57 V and VBACKUP < 2.57 V | 10 | ||
| VRTC output voltage accuracy | VO | -1 | 1 | % | VSYSIN = VBACKUP = 0 V; IO = 0 mA | 10 | |
| VDCDC1 forward current limit | 1.94 | 2.19 | 2.44 | A | 2.5 V < VI(MAIN) < 6 V | 11 | |
| VDCDC1 oscillator frequency | fS | 1.95 | 2.25 | 2.55 | MHz | 11 | |
| VDCDC1 fixed output voltage, FPWMDCDC1 = 0 | -2 | 2 | % | VINDCDC1 = 2.5 V to 6 V; 0 mA ≤ IO ≤ 1.7 A | 11 | ||
| VDCDC1 P-channel on-resistance | rDS(on) | 125 | 261 | mΩ | VINDCDC1 = V(GS) = 3.6 V | 11 | |
| VDCDC2 forward current limit | ILIMF | 1.74 | 1.94 | 2.12 | A | 2.5 V < VINDCDC2 < 6 V | 12 |
| VDCDC3 forward current limit | 1.28 | 1.49 | 1.69 | A | 2.5 V < VINDCDC3 < 6 V | 12 | |
| I2C clock frequency (TPS65023B) | fMAX | 400 | kHz | VCC = 2.5 V to 5.5 V | 13 | ||
| I2C data input hold time (TPS65023B) | th(DATA) | 100 | ns | VCC = 2.5 V to 5.5 V | 13 | ||
| I2C data input setup time (TPS65023B) | tsu(DATA) | 100 | ns | VCC = 2.5 V to 5.5 V | 13 |
CAD (KiCad official)
- Symbol:
TPS65023BRSBR - Footprint:
Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm - 3D model: WQFN-40-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
tps65023brsbr-etched.step/tps65023brsbr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps65023brsbr.step/tps65023brsbr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (56 pp, sha256
1a96eac1a7a70fa5, retrieved 2026-10-26, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS65023BRSBR
**Texas Instruments** · Battery Management ICs · WQFN-40-EP(5x5)
TPS65023BRSBR from Texas Instruments, in a WQFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DEFDCDC3 | input | Input signal indicating default VDCDC3 voltage, 0 = 1.8 V, 1 = 3.3 V, or connect to a resistor divider between VDCDC3 and GND for an output set from 0.6 V to VINDCDC3. |
| 2 | VDCDC3 | input | VDCDC3 feedback voltage sense input, connect directly to VDCDC3. |
| 3 | PGND3 | power_in | Power ground for VDCDC3 converter. |
| 4 | L3 | output | Switch pin of VDCDC3 converter, where the VDCDC3 inductor is connected. |
| 5 | VINDCDC3 | power_in | Input voltage for VDCDC3 step-down converter, must be connected to the same supply as VINDCDC1, VINDCDC2 and VCC. |
| 6 | VINDCDC1 | power_in | Input voltage for VDCDC1 step-down converter, must be connected to the same supply as VINDCDC2, VINDCDC3 and VCC. |
| 7 | L1 | output | Switch pin of VDCDC1 converter, where the VDCDC1 inductor is connected. |
| 8 | PGND1 | power_in | Power ground for VDCDC1 converter. |
| 9 | VDCDC1 | input | VDCDC1 feedback voltage sense input, connect directly to VDCDC1. |
| 10 | DEFDCDC1 | input | Input signal indicating default VDCDC1 voltage, 0 = 1.2 V, 1 = 1.6 V, or connect to a resistor divider between VDCDC1 and GND for an output set from 0.6 V to VINDCDC1. |
| 11 | HOT_RESET | input | Push button input that reboots or wakes up the processor through the RESPWRON output pin. |
| 12 | DEFLDO1 | input | Digital input that sets the default output voltage of LDO1 and LDO2. |
| 13 | DEFLDO2 | input | Digital input that sets the default output voltage of LDO1 and LDO2. |
| 14 | VSYSIN | power_in | Input of system voltage for the VRTC switch. |
| 15 | VBACKUP | power_in | Connect the backup battery to this input pin. |
| 16 | VRTC | power_out | Output voltage of the LDO and switch for the real time clock. |
| 17 | AGND2 | power_in | Analog ground, all analog ground pins are connected internally on the chip. |
| 18 | VLDO2 | power_out | Output voltage of LDO2. |
| 19 | VINLDO | power_in | Input voltage for LDO1 and LDO2. |
| 20 | VLDO1 | power_out | Output voltage of LDO1. |
| 21 | LOWBAT | output | Open-drain output of the LOW_BAT comparator. |
| 22 | LDO_EN | input | Enable input for LDO1 and LDO2, logic high enables the LDOs and logic low disables them. |
| 23 | DCDC3_EN | input | VDCDC3 enable pin, logic high enables the regulator and logic low disables it. |
| 24 | DCDC2_EN | input | VDCDC2 enable pin, logic high enables the regulator and logic low disables it. |
| 25 | DCDC1_EN | input | VDCDC1 enable pin, logic high enables the regulator and logic low disables it. |
| 26 | TRESPWRON | input | Connect the timing capacitor here to set the reset delay time, 1 nF gives 100 ms. |
| 27 | RESPWRON | output | Open-drain system reset output. |
| 28 | INT | output | Open-drain output. |
| 29 | SDAT | bidirectional | Serial interface data and address. |
| 30 | SCLK | input | Serial interface clock line. |
| 31 | PWRFAIL | output | Open-drain output, active low when the PWRFAIL comparator indicates a low VBAT condition. |
| 32 | DEFDCDC2 | input | Input signal indicating default VDCDC2 voltage, 0 = 1.8 V, 1 = 3.3 V, or connect to a resistor divider between VDCDC2 and GND for an output set from 0.6 V to VINDCDC2. |
| 33 | VDCDC2 | input | VDCDC2 feedback voltage sense input, connect directly to VDCDC2. |
| 34 | PGND2 | power_in | Power ground for VDCDC2 converter. |
| 35 | L2 | output | Switch pin of VDCDC2 converter, where the VDCDC2 inductor is connected. |
| 36 | VINDCDC2 | power_in | Input voltage for VDCDC2 step-down converter, must be connected to the same supply as VINDCDC1, VINDCDC3 and VCC. |
| 37 | VCC | power_in | Power supply for digital and analog circuitry of the three DC-DC converters and the serial interface, must be connected to the same supply as VINDCDC1, VINDCDC2 and VINDCDC3. |
| 38 | PWRFAIL_SNS | input | Input for the comparator driving the PWRFAIL output. |
| 39 | LOWBAT_SNS | input | Input for the comparator driving the LOW_BAT output. |
| 40 | AGND1 | power_in | Analog ground, all analog ground pins are connected internally on the chip. |
| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-40-EP(5x5) |
| Category | Power Supply Chip |
| Pins | 41 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage on all pins except AGND and PGND, wrt AGND | VI | -0.3 | | 7 | V | over operating free-air temperature range | 7 |
| Current at VINDCDCx, Lx, PGNDx | | | | 2000 | mA | | 7 |
| Peak current at all other pins | | | | 1000 | mA | | 7 |
| Operating free-air temperature (abs max table) | TA | -40 | | 85 | °C | | 7 |
| Maximum junction temperature | TJ | | | 125 | °C | | 7 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 7 |
| ESD HBM | V(ESD) | -2000 | | 2000 | V | ANSI/ESDA/JEDEC JS-001 | 7 |
| ESD CDM | V(ESD) | -500 | | 500 | V | JESD22-C101 | 7 |
| Input voltage step-down converters | VCC | 2.5 | | 6 | V | VINDCDC1, VINDCDC2, VINDCDC3 tied to same rail | 7 |
| Output voltage VDCDC1 | VO | 0.6 | | 6 | V | max printed as VINDCDC1; 6 V is the VINDCDC1 maximum | 7 |
| Input voltage for LDOs | VI | 1.5 | | 6.5 | V | VINLDO1, VINLDO2 | 7 |
| Output voltage for LDOs | VO | 1 | | | V | max printed as VINLDO1-2 | 7 |
| Output current at L1 | IO(DCDC1) | | | 1700 | mA | | 7 |
| Output current at L2 | IO(DCDC2) | | | 1200 | mA | | 7 |
| Output current at L3 | IO(DCDC3) | | | 1000 | mA | | 7 |
| Inductor at L1/L2/L3 | | 1.5 | 2.2 | | μH | | 7 |
| Output capacitor at VDCDC1/2/3 | CO | 10 | 22 | | μF | | 7 |
| Input capacitor at VINDCDCx | CI | 10 | | | μF | | 7 |
| Output current at VLDO1, VLDO2 | IO(VLDO1-2) | | | 200 | mA | | 8 |
| Output capacitor at VRTC | CO(VRTC) | 4.7 | | | μF | | 8 |
| Operating ambient temperature | TA | -40 | | 85 | °C | | 8 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 8 |
| Resistor from VINDCDCx to VCC for filtering | | 1 | | 10 | Ω | | 8 |
| Junction-to-ambient thermal resistance | RθJA | | 32.7 | | °C/W | RSB (WQFN) 40 pins | 8 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 15.3 | | °C/W | | 8 |
| Junction-to-board thermal resistance | RθJB | | 13.6 | | °C/W | | 8 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 1.1 | | °C/W | | 8 |
| High level input voltage for SCLK pin (TPS65023B) | VIH | 1.4 | | | V | Rpullup at SCLK = 4.7 kΩ, pulled to VRTC; VCC = 2.5 V to 5.25 V | 8 |
| High level input voltage for SDAT pin (TPS65023B) | VIH | 1.69 | | | V | Rpullup at SDAT = 4.7 kΩ, pulled to VRTC; VCC = 2.5 V to 5.25 V | 8 |
| High level input voltage for SDAT pin (TPS65023B) | VIH | 1.55 | | | V | Rpullup at SDAT = 4.7 kΩ, pulled to VRTC; VCC = 2.5 V to 4.5 V | 8 |
| Low level input voltage SCLK/SDAT (TPS65023B) | VIL | 0 | | 0.35 | V | Rpullup at SCLK and SDAT = 4.7 kΩ, pulled to VRTC | 8 |
| Input bias current SCLK/SDAT | IH | | 0.01 | 0.1 | μA | | 8 |
| High-level input voltage (HOT_RESET, ENs, DEFLDOx) | VIH | 1.3 | | | V | max printed as VCC | 8 |
| Low-level input voltage (HOT_RESET, ENs, DEFLDOx) | VIL | 0 | | 0.4 | V | | 8 |
| Deglitch time at HOT_RESET | tdeglitch | 25 | 30 | 35 | ms | | 8 |
| Low-level output voltage | VOL | 0 | | 0.3 | V | IIL = 5 mA | 9 |
| Internal charge/discharge current on TRESPWRON | ICONST | 1.7 | 2 | 2.3 | μA | Used for generating RESPWRON delay | 9 |
| TRESPWRON lower comparator threshold | TRESPWRON_LOWTH | 0.225 | 0.25 | 0.275 | V | Used for generating RESPWRON delay | 9 |
| TRESPWRON upper comparator threshold | TRESPWRON_UPTH | 0.97 | 1 | 1.103 | V | Used for generating RESPWRON delay | 9 |
| LDO1/LDO2 output voltage accuracy | | -2 | | 1 | % | IO = 10 mA | 9 |
| LDO1/LDO2 dropout | | | 65 | 150 | mV | IO = 50 mA, VINLDO = 1.5 V | 9 |
| LDO1/LDO2 line regulation | | -1 | | 1 | % | VINLDO1,2 = VLDO1,2 + 0.5 V (min. 2.5 V) to 6.5 V, IO = 10 mA | 9 |
| LDO1/LDO2 load regulation | | -1 | | 1 | % | IO = 0 mA to 50 mA | 9 |
| Thermal shutdown | T(SD) | | 160 | | °C | Increasing junction temperature | 9 |
| Internal UVLO | UVLO | -2 | 2.35 | 2 | V | VCC falling; tolerance in % | 9 |
| Voltage detector comparator threshold | | -1 | 1 | 1 | V | Falling threshold; tolerance in % | 9 |
| Power-good falling threshold | V(PGOODF) | -12 | -10 | -8 | % | VDCDC1-3, VLDO1, VLDO2, decreasing | 9 |
| Operating quiescent current, PFM | I(q) | | 85 | 100 | μA | All 3 DCDC converters enabled, zero load, no switching, LDOs enabled; VCC = 3.6 V, VBACKUP = 3 V; V(VSYSIN) = 0 V | 10 |
| Quiescent current, all converters disabled | I(q) | | 23 | 33 | μA | All converters disabled, LDOs off; VCC = 3.6 V, VBACKUP = 3 V; V(VSYSIN) = 0 V | 10 |
| Current into VCC, PWM | II | | 2 | 3 | mA | All 3 DCDC converters enabled and running in PWM, LDOs off; VCC = 3.6 V | 10 |
| VRTC output current | IO | | | 30 | mA | VSYSIN < 2.57 V and VBACKUP < 2.57 V | 10 |
| VRTC output voltage accuracy | VO | -1 | | 1 | % | VSYSIN = VBACKUP = 0 V; IO = 0 mA | 10 |
| VDCDC1 forward current limit | | 1.94 | 2.19 | 2.44 | A | 2.5 V < VI(MAIN) < 6 V | 11 |
| VDCDC1 oscillator frequency | fS | 1.95 | 2.25 | 2.55 | MHz | | 11 |
| VDCDC1 fixed output voltage, FPWMDCDC1 = 0 | | -2 | | 2 | % | VINDCDC1 = 2.5 V to 6 V; 0 mA ≤ IO ≤ 1.7 A | 11 |
| VDCDC1 P-channel on-resistance | rDS(on) | | 125 | 261 | mΩ | VINDCDC1 = V(GS) = 3.6 V | 11 |
| VDCDC2 forward current limit | ILIMF | 1.74 | 1.94 | 2.12 | A | 2.5 V < VINDCDC2 < 6 V | 12 |
| VDCDC3 forward current limit | | 1.28 | 1.49 | 1.69 | A | 2.5 V < VINDCDC3 < 6 V | 12 |
| I2C clock frequency (TPS65023B) | fMAX | | | 400 | kHz | VCC = 2.5 V to 5.5 V | 13 |
| I2C data input hold time (TPS65023B) | th(DATA) | 100 | | | ns | VCC = 2.5 V to 5.5 V | 13 |
| I2C data input setup time (TPS65023B) | tsu(DATA) | 100 | | | ns | VCC = 2.5 V to 5.5 V | 13 |
## CAD (KiCad official)
- Symbol: `TPS65023BRSBR`
- Footprint: `Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm`
- 3D model: WQFN-40-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `tps65023brsbr-etched.step` / `tps65023brsbr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps65023brsbr.step` / `tps65023brsbr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps65023b) (56 pp, sha256 `1a96eac1a7a70fa5`, retrieved 2026-10-26, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps65023brsbr-datasheet.pdf)