main
Ray
Publish 0.1.0
157bebe
TPS62933FDRLR
Texas Instruments · DC-DC Converters · SOT-583
TPS62933FDRLR from Texas Instruments, in a SOT-583. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RT | input | Frequency programming input: float for 500 kHz, tie to GND for 1.2 MHz, or connect to an RT timing resistor to set the 200 kHz to 2.2 MHz switching range. |
| 2 | EN | input | Enable input: driving EN high or leaving it floating enables the converter, and an external resistor divider can implement an adjustable VIN UVLO; absolute maximum is 6 V. |
| 3 | VIN | power_in | Supply input to the internal LDO and high-side FET, with input bypass capacitors connected directly to this pin and GND; recommended input range is 3.8 V to 30 V. |
| 4 | GND | power_in | Ground pin connected to the low-side FET source and controller ground, with the path to CIN kept as short as possible. |
| 5 | SW | power_out | Switching output connected to the high-side FET source and low-side FET drain, which drives the power inductor; absolute maximum DC is 32 V. |
| 6 | BST | passive | Bootstrap capacitor connection for the high-side FET driver; connect a high-quality 100-nF ceramic capacitor from this pin to SW. |
| 7 | SS | input | Soft-start control pin for the TPS62933F; a minimum 6.8-nF ceramic capacitor sets the minimum soft-start time to approximately 1 ms, and the pin must not float. |
| 8 | FB | input | Output feedback input connected to the tap of an external resistor divider from the output to GND to set the output voltage from 0.8 V to 22 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-583 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input operation voltage | VIN | 3.8 | 30 | V | 6 | ||
| Input undervoltage lockout threshold, rising | VIN_UVLO | 3.4 | 3.6 | 3.8 | V | Rising threshold | 6 |
| Input undervoltage lockout threshold, falling | VIN_UVLO | 3.1 | 3.3 | 3.5 | V | Falling threshold | 6 |
| FB voltage | VFB | 792 | 800 | 808 | mV | TJ = 25°C | 6 |
| FB voltage | VFB | 788 | 800 | 812 | mV | TJ = 0°C to 85°C | 6 |
| FB voltage | VFB | 784 | 800 | 816 | mV | TJ = -40°C to 150°C | 6 |
| High-side MOSFET current limit | IHS_LIMIT | 4.2 | 5 | 5.8 | A | TPS62933 and TPS62933x | 6 |
| Low-side MOSFET current limit | ILS_LIMIT | 2.9 | 3.8 | 4.5 | A | TPS62933 and TPS62933x | 7 |
| Reverse current limit | ILS_NOC | 1.2 | 2.4 | 3.6 | A | TPS62933F | 7 |
| Soft-start charge current | ISS | 4.5 | 5.5 | 6.5 | µA | TPS62932, TPS62933, and TPS62933F | 7 |
| Switching center frequency | fSW | 450 | 500 | 550 | kHz | RT = floating | 7 |
| Switching center frequency | fSW | 1000 | 1200 | 1350 | kHz | RT = GND | 7 |
| Output OVP threshold | VOVP | 112 | 115 | 118 | % | OVP detect (L→H) | 7 |
| Internal spread oscillator frequency | fspread | -6 | 6 | % | 8 | ||
| Input voltage | VIN | 3.8 | 30 | V | 5 | ||
| EN pin voltage | EN | -0.1 | 5.5 | V | 5 | ||
| FB pin voltage | FB | -0.1 | 5.5 | V | 5 | ||
| Output voltage | VOUT | 0.8 | 22 | V | 5 | ||
| SW DC voltage | SW | -0.1 | 30 | V | DC | 5 | |
| SW transient voltage | SW | -3 | 32 | V | transient < 10 ns | 5 | |
| BST-SW voltage | BST-SW | -0.1 | 5.5 | V | 5 | ||
| Output current | IOUT | 0 | 3 | A | TPS62933, TPS62933x | 5 | |
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Input voltage | VIN | -0.3 | 32 | V | 5 | ||
| EN voltage | EN | -0.3 | 6 | V | 5 | ||
| FB voltage | FB | -0.3 | 6 | V | 5 | ||
| SW DC voltage | SW | -0.3 | 32 | V | DC | 5 | |
| SW transient voltage | SW | -3 | 33 | V | transient < 10 ns | 5 | |
| BST-SW voltage | BST-SW | -0.3 | 6 | V | 5 | ||
| SS voltage | SS/PG | -0.3 | 6 | V | 5 | ||
| RT voltage | RT | -0.3 | 6 | V | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 112.2 | °C/W | JEDEC board, not for design use | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 29.1 | °C/W | JEDEC board | 6 | ||
| Junction-to-board thermal resistance | RθJB | 19.3 | °C/W | JEDEC board | 6 | ||
| Junction-to-top characterization parameter | ΨJT | 1.6 | °C/W | JEDEC board | 6 | ||
| Junction-to-board characterization parameter | ΨJB | 19.2 | °C/W | JEDEC board | 6 | ||
| Junction-to-ambient thermal resistance on official EVM board | RθJA_EVM | 60.2 | °C/W | official EVM board | 6 |
CAD (Adom-generated)
- Symbol:
TPS62933FDRLR - Footprint:
Adom_Gen:Texas_Instruments_TPS62933_af1b3d - 3D model: generated to fit the land (STEP)
- 3D model files:
tps62933fdrlr-etched.step/tps62933fdrlr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps62933fdrlr.step/tps62933fdrlr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
16ec2eac43c7374e, retrieved 2026-11-18) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
# TPS62933FDRLR
**Texas Instruments** · DC-DC Converters · SOT-583
TPS62933FDRLR from Texas Instruments, in a SOT-583. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RT | input | Frequency programming input: float for 500 kHz, tie to GND for 1.2 MHz, or connect to an RT timing resistor to set the 200 kHz to 2.2 MHz switching range. |
| 2 | EN | input | Enable input: driving EN high or leaving it floating enables the converter, and an external resistor divider can implement an adjustable VIN UVLO; absolute maximum is 6 V. |
| 3 | VIN | power_in | Supply input to the internal LDO and high-side FET, with input bypass capacitors connected directly to this pin and GND; recommended input range is 3.8 V to 30 V. |
| 4 | GND | power_in | Ground pin connected to the low-side FET source and controller ground, with the path to CIN kept as short as possible. |
| 5 | SW | power_out | Switching output connected to the high-side FET source and low-side FET drain, which drives the power inductor; absolute maximum DC is 32 V. |
| 6 | BST | passive | Bootstrap capacitor connection for the high-side FET driver; connect a high-quality 100-nF ceramic capacitor from this pin to SW. |
| 7 | SS | input | Soft-start control pin for the TPS62933F; a minimum 6.8-nF ceramic capacitor sets the minimum soft-start time to approximately 1 ms, and the pin must not float. |
| 8 | FB | input | Output feedback input connected to the tap of an external resistor divider from the output to GND to set the output voltage from 0.8 V to 22 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-583 |
| Category | Power Management (PMIC) |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input operation voltage | VIN | 3.8 | | 30 | V | | 6 |
| Input undervoltage lockout threshold, rising | VIN_UVLO | 3.4 | 3.6 | 3.8 | V | Rising threshold | 6 |
| Input undervoltage lockout threshold, falling | VIN_UVLO | 3.1 | 3.3 | 3.5 | V | Falling threshold | 6 |
| FB voltage | VFB | 792 | 800 | 808 | mV | TJ = 25°C | 6 |
| FB voltage | VFB | 788 | 800 | 812 | mV | TJ = 0°C to 85°C | 6 |
| FB voltage | VFB | 784 | 800 | 816 | mV | TJ = -40°C to 150°C | 6 |
| High-side MOSFET current limit | IHS_LIMIT | 4.2 | 5 | 5.8 | A | TPS62933 and TPS62933x | 6 |
| Low-side MOSFET current limit | ILS_LIMIT | 2.9 | 3.8 | 4.5 | A | TPS62933 and TPS62933x | 7 |
| Reverse current limit | ILS_NOC | 1.2 | 2.4 | 3.6 | A | TPS62933F | 7 |
| Soft-start charge current | ISS | 4.5 | 5.5 | 6.5 | µA | TPS62932, TPS62933, and TPS62933F | 7 |
| Switching center frequency | fSW | 450 | 500 | 550 | kHz | RT = floating | 7 |
| Switching center frequency | fSW | 1000 | 1200 | 1350 | kHz | RT = GND | 7 |
| Output OVP threshold | VOVP | 112 | 115 | 118 | % | OVP detect (L→H) | 7 |
| Internal spread oscillator frequency | fspread | -6 | | 6 | % | | 8 |
| Input voltage | VIN | 3.8 | | 30 | V | | 5 |
| EN pin voltage | EN | -0.1 | | 5.5 | V | | 5 |
| FB pin voltage | FB | -0.1 | | 5.5 | V | | 5 |
| Output voltage | VOUT | 0.8 | | 22 | V | | 5 |
| SW DC voltage | SW | -0.1 | | 30 | V | DC | 5 |
| SW transient voltage | SW | -3 | | 32 | V | transient < 10 ns | 5 |
| BST-SW voltage | BST-SW | -0.1 | | 5.5 | V | | 5 |
| Output current | IOUT | 0 | | 3 | A | TPS62933, TPS62933x | 5 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 5 |
| Input voltage | VIN | -0.3 | | 32 | V | | 5 |
| EN voltage | EN | -0.3 | | 6 | V | | 5 |
| FB voltage | FB | -0.3 | | 6 | V | | 5 |
| SW DC voltage | SW | -0.3 | | 32 | V | DC | 5 |
| SW transient voltage | SW | -3 | | 33 | V | transient < 10 ns | 5 |
| BST-SW voltage | BST-SW | -0.3 | | 6 | V | | 5 |
| SS voltage | SS/PG | -0.3 | | 6 | V | | 5 |
| RT voltage | RT | -0.3 | | 6 | V | | 5 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 5 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 5 |
| Junction-to-ambient thermal resistance | RθJA | | 112.2 | | °C/W | JEDEC board, not for design use | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 29.1 | | °C/W | JEDEC board | 6 |
| Junction-to-board thermal resistance | RθJB | | 19.3 | | °C/W | JEDEC board | 6 |
| Junction-to-top characterization parameter | ΨJT | | 1.6 | | °C/W | JEDEC board | 6 |
| Junction-to-board characterization parameter | ΨJB | | 19.2 | | °C/W | JEDEC board | 6 |
| Junction-to-ambient thermal resistance on official EVM board | RθJA_EVM | | 60.2 | | °C/W | official EVM board | 6 |
## CAD (Adom-generated)
- Symbol: `TPS62933FDRLR`
- Footprint: `Adom_Gen:Texas_Instruments_TPS62933_af1b3d`
- 3D model: generated to fit the land (STEP)
- 3D model files: `tps62933fdrlr-etched.step` / `tps62933fdrlr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps62933fdrlr.step` / `tps62933fdrlr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps62933f.pdf) (51 pp, sha256 `16ec2eac43c7374e`, retrieved 2026-11-18)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.
[Datasheet PDF](docs/tps62933fdrlr-datasheet.pdf)