main
Ray
Publish 0.1.0
8118a3a
TPS61196PWPRQ1
Texas Instruments · LED Drivers · HTSSOP-28-EP
TPS61196PWPRQ1 from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | UVLO | input | Low input voltage lockout; use a resistor divider from VIN to this pin to set the UVLO threshold (1.229-V threshold, pull up to VDD if unused). |
| 2 | EN | input | Enable pin, high = enable and low = disable (enabled above 1.8 V, disabled below 1 V). |
| 3 | PWM1 | input | PWM dimming signal input for string 1, with a PWM frequency range of 90 Hz to 22 kHz. |
| 4 | PWM2 | input | PWM dimming signal input for string 2, with a PWM frequency range of 90 Hz to 22 kHz. |
| 5 | PWM3 | input | PWM dimming signal input for string 3, with a PWM frequency range of 90 Hz to 22 kHz. |
| 6 | PWM4 | input | PWM dimming signal input for string 4, with a PWM frequency range of 90 Hz to 22 kHz. |
| 7 | PWM5 | input | PWM dimming signal input for string 5, with a PWM frequency range of 90 Hz to 22 kHz. |
| 8 | PWM6 | input | PWM dimming signal input for string 6, with a PWM frequency range of 90 Hz to 22 kHz. |
| 9 | FBP | passive | LED cross-short protection threshold program pin; use a resistor to GND to set the threshold. |
| 10 | ISET | passive | A resistor on this pin programs the IFB pin current level for full (100% dimming) brightness; sourcing more than 150 µA disables the current sinks. |
| 11 | IFBV | passive | Minimum feedback voltage setting for the LED strings. |
| 12 | IFB1 | input | Regulated current sink input for LED string 1. |
| 13 | IFB2 | input | Regulated current sink input for LED string 2. |
| 14 | IFB3 | input | Regulated current sink input for LED string 3. |
| 15 | IFB4 | input | Regulated current sink input for LED string 4. |
| 16 | IFB5 | input | Regulated current sink input for LED string 5. |
| 17 | IFB6 | input | Regulated current sink input for LED string 6. |
| 18 | AGND | power_in | Analog ground. |
| 19 | OVP | input | Overvoltage protection detection input; connect a resistor divider from the output to this pin to program the OVP threshold. |
| 20 | COMP | output | Loop compensation output for the boost converter; connect an RC network to make the loop stable. |
| 21 | REF | output | Internal reference voltage for the boost converter; a capacitor (1 µF to 4.7 µF) sets the soft-start time, and in parallel operation the master's REF connects to the slave's COMP. |
| 22 | PGND | power_in | External MOSFET current sense ground. |
| 23 | ISNS | input | External MOSFET current sense positive input (connected to ground on a slave device). |
| 24 | GDRV | output | External switch MOSFET gate driver output. |
| 25 | VDD | power_out | Internal regulator output for device internal supply; connect a 1-µF ceramic capacitor, with 15 mA sourcing capability. |
| 26 | FSW | bidirectional | Switching frequency setting pin using a resistor for 100 kHz to 800 kHz; an external voltage above 3.5 V or below 0.5 V disables the internal clock and makes the device a slave. |
| 27 | FAULT | output | Fault indicator, open-drain output that goes high impedance when a fault condition occurs. |
| 28 | VIN | power_in | Power supply input pin (8 V to 30 V operating range). |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-28-EP |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN pin | VIN | -0.3 | 33 | V | 4 | ||
| FAULT pin | -0.3 | V | max printed as VIN | 4 | |||
| IFB1 to IFB6 pins | -0.3 | 40 | V | 4 | |||
| FBP, ISET, ISNS, IFBV pins | -0.3 | 3.3 | V | 4 | |||
| EN, PWM1 to PWM6 pins | -0.3 | 20 | V | 4 | |||
| GDRV pins | -0.3 | 7 | V | 4 | |||
| GDRV 10-ns transient | -2 | 9 | V | 10-ns transient | 4 | ||
| All other pins | -0.3 | 7 | V | 4 | |||
| Operating junction temperature range | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | Human-body model, AEC Q100-002 | 4 | |
| ESD CDM | V(ESD) | -750 | 750 | V | Charged-device model, AEC Q100-011 | 4 | |
| Input voltage | VIN | 8 | 30 | V | 4 | ||
| Output voltage | VOUT | 120 | V | min printed as VIN | 4 | ||
| Inductor | L1 | 10 | 100 | µH | 4 | ||
| Input capacitor | CIN | 10 | µF | 4 | |||
| Output capacitor | COUT | 22 | 220 | µF | 4 | ||
| Boost regulator switching frequency | fSW | 100 | 800 | kHz | 4 | ||
| PWM dimming frequency | fDIM | 0.09 | 22 | kHz | 4 | ||
| Operating ambient temperature | TA | -40 | 125 | °C | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 33.8 | °C/W | PWP (HTSSOP) 28 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 18.8 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 15.6 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 2.5 | °C/W | 5 | |||
| Input voltage range | VIN | 8 | 30 | V | 5 | ||
| Undervoltage lockout threshold | VVIN_UVLO | 6.5 | 7 | V | VIN falling | 5 | |
| VIN UVLO hysteresis | VVIN_HYS | 300 | mV | 5 | |||
| Regulation voltage for internal VDD circuit | 5.7 | 6 | 6.3 | V | 0 mA < IDD < 15 mA | 5 | |
| Logic high input on EN, PWMx | VH | 1.8 | V | VIN = 8 V to 30 V | 5 | ||
| Logic low input on EN, PWMx | VL | 0.8 | V | VIN = 8 V to 30 V | 5 | ||
| Pull-down resistance on EN, PWMx | RPD | 0.8 | 1.6 | 3 | MΩ | 5 | |
| Threshold voltage at UVLO pin | VUVLOTH | 1.204 | 1.229 | 1.253 | V | 5 | |
| UVLO input bias current (below threshold) | IUVLO | -0.1 | 0.1 | µA | VUVLO = VUVLOTH, 50 mV | 5 | |
| UVLO input bias current (above threshold) | IUVLO | -4.3 | -3.9 | -3.3 | µA | VUVLO = VUVLOTH + 50 mV | 5 |
| ISET pin voltage | VISET | 1.217 | 1.229 | 1.24 | V | 5 | |
| ISET short-to-ground protection threshold | IISET_P | 120 | 150 | 180 | µA | 5 | |
| Current multiple IIFB/IISET | KISET | 3932 | 3992 | 4052 | IISET = 32.56 µA, VIFB = 0.5 V | 5 | |
| Current accuracy | IIFB(AVG) | 127.4 | 130 | 132.6 | mA | IISET = 32.56 µA, VIFB = 0.5 V | 5 |
| Current matching | KIFB(M) | 0.5 | 1.5 | % | IISET = 32.56 µA, VIFB = 0.5 V | 5 | |
| IFB pin leakage current at dimming off | IIFB_LEAK | 1 | µA | IFB voltage < 40 V | 5 | ||
| Current sink max output current | IIFB_max | 130 | mA | VIFBV = 350 mV | 5 | ||
| IIFBV sourcing current at IFBV | IIFBV | 0.247 | 0.25 | 0.253 | IISET | VIFBV = 0.5 V | 6 |
| IFBV voltage setting range | VIFBV | 0.3 | 1 | V | 6 | ||
| Reference voltage range for Boost Controller | VREF | 0 | 3.1 | V | 6 | ||
| Leakage current at REF pin | IREF_LEAK | -25 | 25 | nA | 6 | ||
| Switching frequency | fSW | 187 | 200 | 213 | kHz | RFSW = 200 kΩ | 6 |
| Maximum duty cycle | Dmax | 90 | 94 | 98 | % | fSW = 200 kHz | 6 |
| Minimum pulse width | ton(min) | 200 | ns | 6 | |||
| FSW logic high input voltage | VFSW_H | 3.5 | V | 6 | |||
| FSW logic low input voltage | VFSW_L | 0.5 | V | 6 | |||
| Error amplifier transconductance | GmEA | 90 | 120 | 150 | µs | 6 | |
| Gate driver impedance sourcing | RGDRV(SRC) | 2 | 3 | Ω | VDD = 6 V, IGDRV = -20 mA | 6 | |
| Gate driver impedance sinking | RGDRV(SNK) | 1 | 1.5 | Ω | VDD = 6 V, IGDRV = 20 mA | 6 | |
| Overcurrent detection threshold | VISNS(OC) | 376 | 400 | 424 | mV | VIN = 8 V to 30 V, TJ = 25°C to 125°C | 6 |
| Output voltage OVP threshold | VOVPTH | 2.95 | 3.02 | 3.09 | V | 6 | |
| OVP leakage current | IOVP | -100 | 0 | 100 | nA | 6 | |
| LED short detection sourcing current | IFBP | 0.247 | 0.25 | 0.253 | IISET | VFBP = 1 V | 6 |
| Leakage current in high impedance | IFAULT_H | 1 | nA | VFAULT = 24 V | 6 | ||
| Sink current at low output | IFAULT_L | 1 | 2 | mA | VFAULT = 1 V | 6 | |
| Thermal shutdown threshold | Tshutdown | 150 | °C | 6 | |||
| Thermal shutdown hysteresis | Thys | 15 | °C | 6 |
CAD (KiCad official)
- Symbol:
TPS61196PWPRQ1 - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files:
tps61196pwprq1-etched.step/tps61196pwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps61196pwprq1.step/tps61196pwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (31 pp, sha256
b02217759d35bad7, retrieved 2026-10-23, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS61196PWPRQ1
**Texas Instruments** · LED Drivers · HTSSOP-28-EP
TPS61196PWPRQ1 from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | UVLO | input | Low input voltage lockout; use a resistor divider from VIN to this pin to set the UVLO threshold (1.229-V threshold, pull up to VDD if unused). |
| 2 | EN | input | Enable pin, high = enable and low = disable (enabled above 1.8 V, disabled below 1 V). |
| 3 | PWM1 | input | PWM dimming signal input for string 1, with a PWM frequency range of 90 Hz to 22 kHz. |
| 4 | PWM2 | input | PWM dimming signal input for string 2, with a PWM frequency range of 90 Hz to 22 kHz. |
| 5 | PWM3 | input | PWM dimming signal input for string 3, with a PWM frequency range of 90 Hz to 22 kHz. |
| 6 | PWM4 | input | PWM dimming signal input for string 4, with a PWM frequency range of 90 Hz to 22 kHz. |
| 7 | PWM5 | input | PWM dimming signal input for string 5, with a PWM frequency range of 90 Hz to 22 kHz. |
| 8 | PWM6 | input | PWM dimming signal input for string 6, with a PWM frequency range of 90 Hz to 22 kHz. |
| 9 | FBP | passive | LED cross-short protection threshold program pin; use a resistor to GND to set the threshold. |
| 10 | ISET | passive | A resistor on this pin programs the IFB pin current level for full (100% dimming) brightness; sourcing more than 150 µA disables the current sinks. |
| 11 | IFBV | passive | Minimum feedback voltage setting for the LED strings. |
| 12 | IFB1 | input | Regulated current sink input for LED string 1. |
| 13 | IFB2 | input | Regulated current sink input for LED string 2. |
| 14 | IFB3 | input | Regulated current sink input for LED string 3. |
| 15 | IFB4 | input | Regulated current sink input for LED string 4. |
| 16 | IFB5 | input | Regulated current sink input for LED string 5. |
| 17 | IFB6 | input | Regulated current sink input for LED string 6. |
| 18 | AGND | power_in | Analog ground. |
| 19 | OVP | input | Overvoltage protection detection input; connect a resistor divider from the output to this pin to program the OVP threshold. |
| 20 | COMP | output | Loop compensation output for the boost converter; connect an RC network to make the loop stable. |
| 21 | REF | output | Internal reference voltage for the boost converter; a capacitor (1 µF to 4.7 µF) sets the soft-start time, and in parallel operation the master's REF connects to the slave's COMP. |
| 22 | PGND | power_in | External MOSFET current sense ground. |
| 23 | ISNS | input | External MOSFET current sense positive input (connected to ground on a slave device). |
| 24 | GDRV | output | External switch MOSFET gate driver output. |
| 25 | VDD | power_out | Internal regulator output for device internal supply; connect a 1-µF ceramic capacitor, with 15 mA sourcing capability. |
| 26 | FSW | bidirectional | Switching frequency setting pin using a resistor for 100 kHz to 800 kHz; an external voltage above 3.5 V or below 0.5 V disables the internal clock and makes the device a slave. |
| 27 | FAULT | output | Fault indicator, open-drain output that goes high impedance when a fault condition occurs. |
| 28 | VIN | power_in | Power supply input pin (8 V to 30 V operating range). |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-28-EP |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN pin | VIN | -0.3 | | 33 | V | | 4 |
| FAULT pin | | -0.3 | | | V | max printed as VIN | 4 |
| IFB1 to IFB6 pins | | -0.3 | | 40 | V | | 4 |
| FBP, ISET, ISNS, IFBV pins | | -0.3 | | 3.3 | V | | 4 |
| EN, PWM1 to PWM6 pins | | -0.3 | | 20 | V | | 4 |
| GDRV pins | | -0.3 | | 7 | V | | 4 |
| GDRV 10-ns transient | | -2 | | 9 | V | 10-ns transient | 4 |
| All other pins | | -0.3 | | 7 | V | | 4 |
| Operating junction temperature range | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| ESD HBM | V(ESD) | -2000 | | 2000 | V | Human-body model, AEC Q100-002 | 4 |
| ESD CDM | V(ESD) | -750 | | 750 | V | Charged-device model, AEC Q100-011 | 4 |
| Input voltage | VIN | 8 | | 30 | V | | 4 |
| Output voltage | VOUT | | | 120 | V | min printed as VIN | 4 |
| Inductor | L1 | 10 | | 100 | µH | | 4 |
| Input capacitor | CIN | 10 | | | µF | | 4 |
| Output capacitor | COUT | 22 | | 220 | µF | | 4 |
| Boost regulator switching frequency | fSW | 100 | | 800 | kHz | | 4 |
| PWM dimming frequency | fDIM | 0.09 | | 22 | kHz | | 4 |
| Operating ambient temperature | TA | -40 | | 125 | °C | | 4 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 4 |
| Junction-to-ambient thermal resistance | RθJA | | 33.8 | | °C/W | PWP (HTSSOP) 28 pins | 5 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 18.8 | | °C/W | | 5 |
| Junction-to-board thermal resistance | RθJB | | 15.6 | | °C/W | | 5 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 2.5 | | °C/W | | 5 |
| Input voltage range | VIN | 8 | | 30 | V | | 5 |
| Undervoltage lockout threshold | VVIN_UVLO | 6.5 | | 7 | V | VIN falling | 5 |
| VIN UVLO hysteresis | VVIN_HYS | | 300 | | mV | | 5 |
| Regulation voltage for internal VDD circuit | | 5.7 | 6 | 6.3 | V | 0 mA < IDD < 15 mA | 5 |
| Logic high input on EN, PWMx | VH | 1.8 | | | V | VIN = 8 V to 30 V | 5 |
| Logic low input on EN, PWMx | VL | | | 0.8 | V | VIN = 8 V to 30 V | 5 |
| Pull-down resistance on EN, PWMx | RPD | 0.8 | 1.6 | 3 | MΩ | | 5 |
| Threshold voltage at UVLO pin | VUVLOTH | 1.204 | 1.229 | 1.253 | V | | 5 |
| UVLO input bias current (below threshold) | IUVLO | -0.1 | | 0.1 | µA | VUVLO = VUVLOTH, 50 mV | 5 |
| UVLO input bias current (above threshold) | IUVLO | -4.3 | -3.9 | -3.3 | µA | VUVLO = VUVLOTH + 50 mV | 5 |
| ISET pin voltage | VISET | 1.217 | 1.229 | 1.24 | V | | 5 |
| ISET short-to-ground protection threshold | IISET_P | 120 | 150 | 180 | µA | | 5 |
| Current multiple IIFB/IISET | KISET | 3932 | 3992 | 4052 | | IISET = 32.56 µA, VIFB = 0.5 V | 5 |
| Current accuracy | IIFB(AVG) | 127.4 | 130 | 132.6 | mA | IISET = 32.56 µA, VIFB = 0.5 V | 5 |
| Current matching | KIFB(M) | | 0.5 | 1.5 | % | IISET = 32.56 µA, VIFB = 0.5 V | 5 |
| IFB pin leakage current at dimming off | IIFB_LEAK | | | 1 | µA | IFB voltage < 40 V | 5 |
| Current sink max output current | IIFB_max | | 130 | | mA | VIFBV = 350 mV | 5 |
| IIFBV sourcing current at IFBV | IIFBV | 0.247 | 0.25 | 0.253 | IISET | VIFBV = 0.5 V | 6 |
| IFBV voltage setting range | VIFBV | 0.3 | | 1 | V | | 6 |
| Reference voltage range for Boost Controller | VREF | 0 | | 3.1 | V | | 6 |
| Leakage current at REF pin | IREF_LEAK | -25 | | 25 | nA | | 6 |
| Switching frequency | fSW | 187 | 200 | 213 | kHz | RFSW = 200 kΩ | 6 |
| Maximum duty cycle | Dmax | 90 | 94 | 98 | % | fSW = 200 kHz | 6 |
| Minimum pulse width | ton(min) | | 200 | | ns | | 6 |
| FSW logic high input voltage | VFSW_H | 3.5 | | | V | | 6 |
| FSW logic low input voltage | VFSW_L | | | 0.5 | V | | 6 |
| Error amplifier transconductance | GmEA | 90 | 120 | 150 | µs | | 6 |
| Gate driver impedance sourcing | RGDRV(SRC) | | 2 | 3 | Ω | VDD = 6 V, IGDRV = -20 mA | 6 |
| Gate driver impedance sinking | RGDRV(SNK) | | 1 | 1.5 | Ω | VDD = 6 V, IGDRV = 20 mA | 6 |
| Overcurrent detection threshold | VISNS(OC) | 376 | 400 | 424 | mV | VIN = 8 V to 30 V, TJ = 25°C to 125°C | 6 |
| Output voltage OVP threshold | VOVPTH | 2.95 | 3.02 | 3.09 | V | | 6 |
| OVP leakage current | IOVP | -100 | 0 | 100 | nA | | 6 |
| LED short detection sourcing current | IFBP | 0.247 | 0.25 | 0.253 | IISET | VFBP = 1 V | 6 |
| Leakage current in high impedance | IFAULT_H | | | 1 | nA | VFAULT = 24 V | 6 |
| Sink current at low output | IFAULT_L | 1 | 2 | | mA | VFAULT = 1 V | 6 |
| Thermal shutdown threshold | Tshutdown | | 150 | | °C | | 6 |
| Thermal shutdown hysteresis | Thys | | 15 | | °C | | 6 |
## CAD (KiCad official)
- Symbol: `TPS61196PWPRQ1`
- Footprint: `Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm`
- 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files: `tps61196pwprq1-etched.step` / `tps61196pwprq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps61196pwprq1.step` / `tps61196pwprq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps61196pwprq1.pdf) (31 pp, sha256 `b02217759d35bad7`, retrieved 2026-10-23, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps61196pwprq1-datasheet.pdf)