component
TPS60201DGS
Public Made by Adomby adom
Texas Instruments DC-DC Converters, VSSOP-10-0.5mm. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+46@@ -0,0 +1,46 @@+# TPS60201DGS++**Texas Instruments** · DC-DC Converters · VSSOP-10-0.5mm++TPS60201DGS from Texas Instruments, in a VSSOP-10-0.5mm. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | GND | power_in | Ground pin for the device; the datasheet states that on TPS60201 the LBI function is not used and LBI must be connected to this GND pin. |+| 2 | GND | power_in | Ground pin for the device. |+| 3 | C1- | passive | Negative terminal of the flying capacitor C1, which uses a 1 µF flying capacitor per the recommended operating conditions. |+| 4 | C1+ | passive | Positive terminal of the flying capacitor C1, which uses a 1 µF flying capacitor per the recommended operating conditions. |+| 5 | OUT | power_out | Regulated 3.3-V power output; bypass OUT to GND with the output filter capacitor CO (2.2 µF recommended). |+| 6 | C2+ | passive | Positive terminal of the flying capacitor C2. |+| 7 | IN | power_in | Supply input with a recommended range of 1.6 V to 3.6 V; bypass IN to GND with a capacitor of the same size as CO. |+| 8 | C2- | passive | Negative terminal of the flying capacitor C2. |+| 9 | EN | input | Device-enable input: EN low disables the device and discharges the output capacitor, EN high runs from the internal oscillator, and an applied external clock puts the device in Sync-Mode. |+| 10 | PG | output | Open-drain power-good output that goes active high when OUT reaches about 90% of its nominal value and requires a pullup to OUT or to a logic rail lower than 3.6 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VSSOP-10-0.5mm |+| Category | Power Supply Chip |+| Pins | 10 |++## CAD (KiCad official)++- Symbol: `TPS60201DGS`+- Footprint: `Package_SO:MSOP-10_3x3mm_P0.5mm`+- 3D model: VSSOP-10-0.5mm (KiCad packages3D, STEP)+- 3D model files: `tps60201dgs-etched.step` / `tps60201dgs-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps60201dgs.step` / `tps60201dgs.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps60200) (28 pp, sha256 `29c132d0f3880a8c`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps60201dgs-datasheet.pdf)
page.jsonadded+212@@ -0,0 +1,212 @@+{+ "slug": "tps60201dgs",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, VSSOP-10-0.5mm. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "tps60201dgs",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps60201dgs.kicad_sym",+ "tps60201dgs.kicad_mod",+ "tps60201dgs.glb",+ "tps60201dgs.step",+ "tps60201dgs.lbr",+ "docs/hero.png",+ "docs/tps60201dgs-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps60201dgs-hero.glb",+ "tps60201dgs-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS60201DGS",+ "manufacturer": "Texas Instruments",+ "package": "VSSOP-10-0.5mm",+ "pin_count": 10,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps60200",+ "parts": {+ "symbol": "tps60201dgs.kicad_sym",+ "footprint": "tps60201dgs.kicad_mod",+ "model_3d": "tps60201dgs-hero.glb",+ "model_3d_plain": "tps60201dgs.glb",+ "model_3d_step": "tps60201dgs-etched.step",+ "model_3d_step_plain": "tps60201dgs.step",+ "lbr": "tps60201dgs.lbr"+ },+ "distributor_links": {+ "lcsc": "C1356006",+ "digikey": "2156-TPS60201DGS-ND",+ "mouser": "595-TPS60201DGS"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T14:35:10Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "2156-TPS60201DGS-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS60201DGS",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "GND",+ "type": "power_in",+ "description": "Ground pin for the device; the datasheet states that on TPS60201 the LBI function is not used and LBI must be connected to this GND pin."+ },+ {+ "number": "2",+ "name": "GND",+ "type": "power_in",+ "description": "Ground pin for the device."+ },+ {+ "number": "3",+ "name": "C1–",+ "type": "passive",+ "description": "Negative terminal of the flying capacitor C1, which uses a 1 µF flying capacitor per the recommended operating conditions."+ },+ {+ "number": "4",+ "name": "C1+",+ "type": "passive",+ "description": "Positive terminal of the flying capacitor C1, which uses a 1 µF flying capacitor per the recommended operating conditions."+ },+ {+ "number": "5",+ "name": "OUT",+ "type": "power_out",+ "description": "Regulated 3.3-V power output; bypass OUT to GND with the output filter capacitor CO (2.2 µF recommended)."+ },+ {+ "number": "6",+ "name": "C2+",+ "type": "passive",+ "description": "Positive terminal of the flying capacitor C2."+ },+ {+ "number": "7",+ "name": "IN",+ "type": "power_in",+ "description": "Supply input with a recommended range of 1.6 V to 3.6 V; bypass IN to GND with a capacitor of the same size as CO."+ },+ {+ "number": "8",+ "name": "C2–",+ "type": "passive",+ "description": "Negative terminal of the flying capacitor C2."+ },+ {+ "number": "9",+ "name": "EN",+ "type": "input",+ "description": "Device-enable input: EN low disables the device and discharges the output capacitor, EN high runs from the internal oscillator, and an applied external clock puts the device in Sync-Mode."+ },+ {+ "number": "10",+ "name": "PG",+ "type": "output",+ "description": "Open-drain power-good output that goes active high when OUT reaches about 90% of its nominal value and requires a pullup to OUT or to a logic rail lower than 3.6 V."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The datasheet's I/O column is blank for the flying-capacitor pins (C1+, C1–, C2+, C2–); their type '; The 0.5 mm pitch in the package hint does not appear in the provided text; the package mapping to DG; Page 4 text is partly garbled. The pinout used is the TPS60201/TPS60203 top view (PG on pin 10, EN o"+ ],+ "pages_sent": 9,+ "cost_usd": 0.0603,+ "at": "2026-10-08T14:34:53"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps60200",+ "pages": 28,+ "sha256": "29c132d0f3880a8c",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 10,+ "described": 10,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps60201dgs.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "b8f88eac3ce221c2ccb0b5048f9ad49c2ef4af148f8ae50c4e232e357683f547",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps60201dgs-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "6440c2da56985f8e6da197d438ebc1a11c819269bc5f830a931e99a8487b0dc9",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}