← Commit history
README.mdadded+52@@ -0,0 +1,52 @@+# TPS54626PWPR++**Texas Instruments** · DC-DC Converters · HTSSOP-14-EP++TPS54626PWPR from Texas Instruments, in a HTSSOP-14-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VO | power_out | Connect to output of converter; also used for the output discharge function. |+| 2 | VFB | input | Converter feedback input; connect with a feedback resistor divider from VO. |+| 3 | VREG5 | power_out | 5.5V internal linear regulator output for control circuitry; a typical 1uF capacitor should be connected to GND; not active when EN is low. |+| 4 | SS | passive | Soft-start control pin; an external capacitor connected to GND sets the soft-start ramp time (6uA typical charge current). |+| 5 | GND | power_in | Signal ground pin for the control circuitry. |+| 6 | PG | output | Open-drain power-good output; requires an external pull-up resistor (25k-150kOhm) to VREG5. |+| 7 | EN | input | Enable control input, active high; must be pulled up to enable the device (internal pull-down resistance to GND of 200-800kOhm). |+| 8 | PGND1 | power_in | Ground return for the low-side MOSFET; also serves as an input to the current comparator; connect strongly to GND near the IC. |+| 9 | PGND2 | power_in | Ground return for the low-side MOSFET; also serves as an input to the current comparator; connect strongly to GND near the IC. |+| 10 | SW1 | output | Switch node connection between the high-side and low-side NFETs; also serves as an input to the current comparator. |+| 11 | SW2 | output | Switch node connection between the high-side and low-side NFETs; also serves as an input to the current comparator. |+| 12 | VBST | passive | Supply input for the high-side NFET gate driver (boost terminal); connect a capacitor from this pin to the SW1/SW2 terminals; an internal PN diode connects VREG5 to this pin. |+| 13 | VIN1 | power_in | Power input, connected to the high-side NFET drain. |+| 14 | VIN2 | power_in | Power input, connected to the high-side NFET drain; an additional 0.1uF capacitor from this pin to ground is recommended to improve stability of the over-current limit function. |+| 15 | PowerPAD | power_in | Exposed thermal pad on the package backside, internally connected to PGND; must be soldered to the PCB ground plane to achieve appropriate power dissipation. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-14-EP |+| Category | Power Supply Chip |+| Pins | 15 |++## CAD (KiCad official)++- Symbol: `TPS54626PWPR`+- Footprint: `Package_SO:TSSOP-14-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-14-EP (KiCad packages3D, STEP)+- 3D model files: `tps54626pwpr-etched.step` / `tps54626pwpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps54626pwpr.step` / `tps54626pwpr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps54626) (23 pp, sha256 `6a77b8bc07cb116a`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps54626pwpr-datasheet.pdf)
page.jsonadded+186@@ -0,0 +1,186 @@+{+ "slug": "tps54626pwpr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, HTSSOP-14-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "tps54626pwpr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps54626pwpr.kicad_sym",+ "tps54626pwpr.kicad_mod",+ "tps54626pwpr.glb",+ "tps54626pwpr.step",+ "tps54626pwpr.lbr",+ "docs/hero.png",+ "docs/tps54626pwpr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "component": {+ "mpn": "TPS54626PWPR",+ "manufacturer": "Texas Instruments",+ "package": "HTSSOP-14-EP",+ "pin_count": 15,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps54626",+ "parts": {+ "symbol": "tps54626pwpr.kicad_sym",+ "footprint": "tps54626pwpr.kicad_mod",+ "model_3d": "tps54626pwpr-etched.glb",+ "model_3d_plain": "tps54626pwpr.glb",+ "model_3d_step": "tps54626pwpr-etched.step",+ "model_3d_step_plain": "tps54626pwpr.step",+ "lbr": "tps54626pwpr.lbr"+ },+ "distributor_links": {+ "lcsc": "C2071308"+ },+ "pins": [+ {+ "number": "1",+ "name": "VO",+ "type": "power_out",+ "description": "Connect to output of converter; also used for the output discharge function."+ },+ {+ "number": "2",+ "name": "VFB",+ "type": "input",+ "description": "Converter feedback input; connect with a feedback resistor divider from VO."+ },+ {+ "number": "3",+ "name": "VREG5",+ "type": "power_out",+ "description": "5.5V internal linear regulator output for control circuitry; a typical 1uF capacitor should be connected to GND; not active when EN is low."+ },+ {+ "number": "4",+ "name": "SS",+ "type": "passive",+ "description": "Soft-start control pin; an external capacitor connected to GND sets the soft-start ramp time (6uA typical charge current)."+ },+ {+ "number": "5",+ "name": "GND",+ "type": "power_in",+ "description": "Signal ground pin for the control circuitry."+ },+ {+ "number": "6",+ "name": "PG",+ "type": "output",+ "description": "Open-drain power-good output; requires an external pull-up resistor (25k-150kOhm) to VREG5."+ },+ {+ "number": "7",+ "name": "EN",+ "type": "input",+ "description": "Enable control input, active high; must be pulled up to enable the device (internal pull-down resistance to GND of 200-800kOhm)."+ },+ {+ "number": "8",+ "name": "PGND1",+ "type": "power_in",+ "description": "Ground return for the low-side MOSFET; also serves as an input to the current comparator; connect strongly to GND near the IC."+ },+ {+ "number": "9",+ "name": "PGND2",+ "type": "power_in",+ "description": "Ground return for the low-side MOSFET; also serves as an input to the current comparator; connect strongly to GND near the IC."+ },+ {+ "number": "10",+ "name": "SW1",+ "type": "output",+ "description": "Switch node connection between the high-side and low-side NFETs; also serves as an input to the current comparator."+ },+ {+ "number": "11",+ "name": "SW2",+ "type": "output",+ "description": "Switch node connection between the high-side and low-side NFETs; also serves as an input to the current comparator."+ },+ {+ "number": "12",+ "name": "VBST",+ "type": "passive",+ "description": "Supply input for the high-side NFET gate driver (boost terminal); connect a capacitor from this pin to the SW1/SW2 terminals; an internal PN diode connects VREG5 to this pin."+ },+ {+ "number": "13",+ "name": "VIN1",+ "type": "power_in",+ "description": "Power input, connected to the high-side NFET drain."+ },+ {+ "number": "14",+ "name": "VIN2",+ "type": "power_in",+ "description": "Power input, connected to the high-side NFET drain; an additional 0.1uF capacitor from this pin to ground is recommended to improve stability of the over-current limit function."+ },+ {+ "number": "15",+ "name": "PowerPAD",+ "type": "power_in",+ "description": "Exposed thermal pad on the package backside, internally connected to PGND; must be soldered to the PCB ground plane to achieve appropriate power dissipation."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.2",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.2",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Exposed thermal pad (PowerPAD) is mentioned in device information section but is not assigned a numb",+ "exposed pad 15 added from the footprint"+ ],+ "pages_sent": 23,+ "cost_usd": 0.2768,+ "at": "2026-09-23T07:41:09"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps54626",+ "pages": 23,+ "sha256": "6a77b8bc07cb116a",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 15,+ "described": 15,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}