component
TPS54356PWPR
Public Made by Adomby adom
Texas Instruments DC-DC Converters, HTSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+53@@ -0,0 +1,53 @@+# TPS54356PWPR++**Texas Instruments** · DC-DC Converters · HTSSOP-16-EP++TPS54356PWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VIN | power_in | Input supply voltage requiring 4.5 V to 20 V with low-ESR 10 µF ceramic bypass capacitor placed close to device pins. |+| 2 | VIN | power_in | Input supply voltage requiring 4.5 V to 20 V with low-ESR 10 µF ceramic bypass capacitor placed close to device pins. |+| 3 | UVLO | input | Undervoltage lockout input with internal voltage divider that can be overridden by external resistive divider from VIN to ground. |+| 4 | PWRGD | tri_state | Open-drain power good output asserted low when output voltage falls below nominal or fault conditions detected with internal rising-edge filter. |+| 5 | RT | input | Frequency setting input programmed by grounding for 250 kHz, floating for 500 kHz, or connecting 69-215 kΩ resistor to ground for 250-700 kHz. |+| 6 | SYNC | bidirectional | Bidirectional synchronization I/O outputting falling-edge signal when RT floating/grounded or accepting external synchronization input when RT resistor used with required 10 kΩ ground resistor. |+| 7 | ENA | input | Enable control input stopping device switching when pulled below 0.5 V threshold with float enabling operation. |+| 8 | COMP | output | Error amplifier output internal node with 1.5 mA drive capability that must not be connected externally. |+| 9 | VSENSE | input | Feedback network input node compared to internal voltage reference for output voltage regulation. |+| 10 | AGND | power_in | Analog ground return for sensitive analog circuitry that must connect to PGND and PowerPAD. |+| 11 | PGND | power_in | Power ground return for LSG driver output currents that must connect to AGND and PowerPAD. |+| 12 | VBIAS | power_out | Internal bias voltage output providing 8.0 V at VIN ≥12 V or 4.4 V at VIN = 4.5 V requiring 1.0 µF ceramic bypass capacitor. |+| 13 | LSG | output | Low-side MOSFET gate driver output with 100 mA source/sink capability connecting to n-channel MOSFET gate or left open for diode-only configuration. |+| 14 | PH | output | Phase node switching output with voltage range from −1.5 V to +22 V connecting to external L-C output filter inductance. |+| 15 | PH | output | Phase node switching output with voltage range from −1.5 V to +22 V connecting to external L-C output filter inductance. |+| 16 | BOOT | output | Bootstrap supply connection for high-side gate driver with 0.1 µF ceramic capacitor connecting from BOOT to PH pins. |+| 17 | PowerPAD | power_in | Exposed thermal pad for junction-to-ambient heat dissipation that must solder to PGND and AGND connections. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-16-EP |+| Category | Power Supply Chip |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `TPS54356PWPR`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `tps54356pwpr-etched.step` / `tps54356pwpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps54356pwpr.step` / `tps54356pwpr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps54356) (37 pp, sha256 `1e7f079dce00c4b2`, retrieved 2026-09-23, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps54356pwpr-datasheet.pdf)
page.jsonadded+197@@ -0,0 +1,197 @@+{+ "slug": "tps54356pwpr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, HTSSOP-16-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "tps54356pwpr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps54356pwpr.kicad_sym",+ "tps54356pwpr.kicad_mod",+ "tps54356pwpr.glb",+ "tps54356pwpr.step",+ "tps54356pwpr.lbr",+ "docs/hero.png",+ "docs/tps54356pwpr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "component": {+ "mpn": "TPS54356PWPR",+ "manufacturer": "Texas Instruments",+ "package": "HTSSOP-16-EP",+ "pin_count": 17,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps54356",+ "parts": {+ "symbol": "tps54356pwpr.kicad_sym",+ "footprint": "tps54356pwpr.kicad_mod",+ "model_3d": "tps54356pwpr-etched.glb",+ "model_3d_plain": "tps54356pwpr.glb",+ "model_3d_step": "tps54356pwpr-etched.step",+ "model_3d_step_plain": "tps54356pwpr.step",+ "lbr": "tps54356pwpr.lbr"+ },+ "distributor_links": {+ "lcsc": "C2071795"+ },+ "pins": [+ {+ "number": "1",+ "name": "VIN",+ "type": "power_in",+ "description": "Input supply voltage requiring 4.5 V to 20 V with low-ESR 10 µF ceramic bypass capacitor placed close to device pins."+ },+ {+ "number": "2",+ "name": "VIN",+ "type": "power_in",+ "description": "Input supply voltage requiring 4.5 V to 20 V with low-ESR 10 µF ceramic bypass capacitor placed close to device pins."+ },+ {+ "number": "3",+ "name": "UVLO",+ "type": "input",+ "description": "Undervoltage lockout input with internal voltage divider that can be overridden by external resistive divider from VIN to ground."+ },+ {+ "number": "4",+ "name": "PWRGD",+ "type": "tri_state",+ "description": "Open-drain power good output asserted low when output voltage falls below nominal or fault conditions detected with internal rising-edge filter."+ },+ {+ "number": "5",+ "name": "RT",+ "type": "input",+ "description": "Frequency setting input programmed by grounding for 250 kHz, floating for 500 kHz, or connecting 69-215 kΩ resistor to ground for 250-700 kHz."+ },+ {+ "number": "6",+ "name": "SYNC",+ "type": "bidirectional",+ "description": "Bidirectional synchronization I/O outputting falling-edge signal when RT floating/grounded or accepting external synchronization input when RT resistor used with required 10 kΩ ground resistor."+ },+ {+ "number": "7",+ "name": "ENA",+ "type": "input",+ "description": "Enable control input stopping device switching when pulled below 0.5 V threshold with float enabling operation."+ },+ {+ "number": "8",+ "name": "COMP",+ "type": "output",+ "description": "Error amplifier output internal node with 1.5 mA drive capability that must not be connected externally."+ },+ {+ "number": "9",+ "name": "VSENSE",+ "type": "input",+ "description": "Feedback network input node compared to internal voltage reference for output voltage regulation."+ },+ {+ "number": "10",+ "name": "AGND",+ "type": "power_in",+ "description": "Analog ground return for sensitive analog circuitry that must connect to PGND and PowerPAD."+ },+ {+ "number": "11",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground return for LSG driver output currents that must connect to AGND and PowerPAD."+ },+ {+ "number": "12",+ "name": "VBIAS",+ "type": "power_out",+ "description": "Internal bias voltage output providing 8.0 V at VIN ≥12 V or 4.4 V at VIN = 4.5 V requiring 1.0 µF ceramic bypass capacitor."+ },+ {+ "number": "13",+ "name": "LSG",+ "type": "output",+ "description": "Low-side MOSFET gate driver output with 100 mA source/sink capability connecting to n-channel MOSFET gate or left open for diode-only configuration."+ },+ {+ "number": "14",+ "name": "PH",+ "type": "output",+ "description": "Phase node switching output with voltage range from −1.5 V to +22 V connecting to external L-C output filter inductance."+ },+ {+ "number": "15",+ "name": "PH",+ "type": "output",+ "description": "Phase node switching output with voltage range from −1.5 V to +22 V connecting to external L-C output filter inductance."+ },+ {+ "number": "16",+ "name": "BOOT",+ "type": "output",+ "description": "Bootstrap supply connection for high-side gate driver with 0.1 µF ceramic capacitor connecting from BOOT to PH pins."+ },+ {+ "number": "17",+ "name": "PowerPAD",+ "type": "power_in",+ "description": "Exposed thermal pad for junction-to-ambient heat dissipation that must solder to PGND and AGND connections."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.2",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.2",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "1/17 pins cited to the wrong page (name found elsewhere): ['17:PowerPAD@p7']"+ ],+ "pages_sent": 37,+ "cost_usd": 0.4246,+ "at": "2026-09-23T18:57:27"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps54356",+ "pages": 37,+ "sha256": "1e7f079dce00c4b2",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 17,+ "described": 17,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}