← Commit history

tps53647rtat: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)

Ray ·d6aacc6cd6 · ·parent 85f1f9c
2 files changed +100−20
package.json+58−18
@@ -59,7 +59,7 @@         "number": "2",         "name": "IMON",         "type": "output",-        "description": "Analog current monitor output generated from summed individual phase currents; output voltage VIMON = F \u00d7 VREF \u00d7 (total current) / (IMAX \u00d7 35k\u03a9)."+        "description": "Analog current monitor output generated from summed individual phase currents; output voltage VIMON = F × VREF × (total current) / (IMAX × 35kΩ)."       },       {         "number": "3",@@ -101,43 +101,43 @@         "number": "9",         "name": "VSP",         "type": "input",-        "description": "Positive input of remote voltage sense amplifier with typical input bias current of 300 \u00b5A; connect directly to load output voltage with differential pair spacing \u2264 10 mil."+        "description": "Positive input of remote voltage sense amplifier with typical input bias current of 300 µA; connect directly to load output voltage with differential pair spacing ≤ 10 mil."       },       {         "number": "10",         "name": "VSN",         "type": "input",-        "description": "Negative input of remote voltage sense amplifier with typical input bias current of -23 \u00b5A; connect directly to load ground."+        "description": "Negative input of remote voltage sense amplifier with typical input bias current of -23 µA; connect directly to load ground."       },       {         "number": "11",         "name": "COMP",         "type": "output",-        "description": "Output of gM error amplifier (gain typically 1000 \u00b5S); external resistors and capacitors connected between this pin and VREF set compensation network."+        "description": "Output of gM error amplifier (gain typically 1000 µS); external resistors and capacitors connected between this pin and VREF set compensation network."       },       {         "number": "12",         "name": "ISUM",         "type": "output",-        "description": "Summed phase current output; resistor (RISUM) connected between this pin and VREF determines droop load-line (VDROOP = gM(isum) \u00d7 RISUM \u00d7 RCS \u00d7 IOUT / 6)."+        "description": "Summed phase current output; resistor (RISUM) connected between this pin and VREF determines droop load-line (VDROOP = gM(isum) × RISUM × RCS × IOUT / 6)."       },       {         "number": "13",         "name": "VREF",         "type": "power_out",-        "description": "1.7-V, 500-\u00b5A LDO reference voltage output; bypass to GND with 0.33 \u00b5F ceramic capacitor and connect to REFIN pin of TI smart power stages."+        "description": "1.7-V, 500-µA LDO reference voltage output; bypass to GND with 0.33 µF ceramic capacitor and connect to REFIN pin of TI smart power stages."       },       {         "number": "14",         "name": "V3R3",         "type": "power_out",-        "description": "3.3-V LDO output generated from V5 with startup time ~600 \u00b5s when V5 exceeds 4.25 V; bypass to GND with 1-4.7 \u00b5F ceramic capacitor."+        "description": "3.3-V LDO output generated from V5 with startup time ~600 µs when V5 exceeds 4.25 V; bypass to GND with 1-4.7 µF ceramic capacitor."       },       {         "number": "15",         "name": "V5",         "type": "power_in",-        "description": "5-V power input for internal analog circuits with UVLO threshold 4.25 V (ok) and 4.05 V (fault) and hysteresis of 0.23 V typical; bypass to GND with 1-4.7 \u00b5F ceramic capacitor."+        "description": "5-V power input for internal analog circuits with UVLO threshold 4.25 V (ok) and 4.05 V (fault) and hysteresis of 0.23 V typical; bypass to GND with 1-4.7 µF ceramic capacitor."       },       {         "number": "16",@@ -155,13 +155,13 @@         "number": "18",         "name": "VR_RDY",         "type": "output",-        "description": "Power good open-drain output (36-50 \u03a9 pull-down resistance at 0.31 V) asserted low when output voltage < (VDAC - VDROOP - 207 mV) or during startup; typically pulled up to V3R3 through 3 k\u03a9 resistor."+        "description": "Power good open-drain output (36-50 Ω pull-down resistance at 0.31 V) asserted low when output voltage < (VDAC - VDROOP - 207 mV) or during startup; typically pulled up to V3R3 through 3 kΩ resistor."       },       {         "number": "19",         "name": "VR_HOT",         "type": "output",-        "description": "Thermal flag open-drain output asserted low when sensed temperature exceeds TMAX threshold (110 \u00b0C default); typically pulled up to V3R3 through 3 k\u03a9 resistor."+        "description": "Thermal flag open-drain output asserted low when sensed temperature exceeds TMAX threshold (110 °C default); typically pulled up to V3R3 through 3 kΩ resistor."       },       {         "number": "20",@@ -173,7 +173,7 @@         "number": "21",         "name": "RESET",         "type": "input",-        "description": "Reset pin with logic low threshold 0.8 V and logic high threshold 1.2 V; if held low > 1000 ns, controller pulls output voltage to VBOOT level with reset delay > 1 \u00b5s."+        "description": "Reset pin with logic low threshold 0.8 V and logic high threshold 1.2 V; if held low > 1000 ns, controller pulls output voltage to VBOOT level with reset delay > 1 µs."       },       {         "number": "22",@@ -209,7 +209,7 @@         "number": "27",         "name": "VR_FAULT",         "type": "output",-        "description": "VR fault indicator open-drain output asserted low for input overcurrent fault, over-temperature fault (>125 \u00b0C), output overvoltage fault (>VDAC + offset), or power stage fault; typically pulled up to V3R3 through 3 k\u03a9 resistor."+        "description": "VR fault indicator open-drain output asserted low for input overcurrent fault, over-temperature fault (>125 °C), output overvoltage fault (>VDAC + offset), or power stage fault; typically pulled up to V3R3 through 3 kΩ resistor."       },       {         "number": "28",@@ -221,7 +221,7 @@         "number": "29",         "name": "SLEW-MODE",         "type": "input",-        "description": "Voltage divider to VREF pin; resistor (RSLEW-MODE) sets one of eight output voltage slew rates (0.34-2.74 mV/\u00b5s); voltage sets 4-bit operation mode bits including VR12.0/12.5, phase interleaving, dynamic phase shedding, and zero load-line."+        "description": "Voltage divider to VREF pin; resistor (RSLEW-MODE) sets one of eight output voltage slew rates (0.34-2.74 mV/µs); voltage sets 4-bit operation mode bits including VR12.0/12.5, phase interleaving, dynamic phase shedding, and zero load-line."       },       {         "number": "30",@@ -239,7 +239,7 @@         "number": "32",         "name": "F-IMAX",         "type": "input",-        "description": "Voltage divider to VREF pin; resistor (RF-IMAX) sets switching frequency (300 kHz to 1 MHz); voltage (VF-IMAX) sets maximum operating current IMAX (8-bit A/D: IMAX = VF-IMAX / VVREF \u00d7 255)."+        "description": "Voltage divider to VREF pin; resistor (RF-IMAX) sets switching frequency (300 kHz to 1 MHz); voltage (VF-IMAX) sets maximum operating current IMAX (8-bit A/D: IMAX = VF-IMAX / VVREF × 255)."       },       {         "number": "33",@@ -281,13 +281,13 @@         "number": "39",         "name": "SKIP-NVM",         "type": "output",-        "description": "Configuration mode select output and SKIP/FCCM mode signal; resistor \u226420 k\u03a9 selects pinstrap mode, \u2265100 k\u03a9 selects NVM mode; can connect to FCCM pin of TI smart power stages for skip/continuous conduction mode operation."+        "description": "Configuration mode select output and SKIP/FCCM mode signal; resistor ≤20 kΩ selects pinstrap mode, ≥100 kΩ selects NVM mode; can connect to FCCM pin of TI smart power stages for skip/continuous conduction mode operation."       },       {         "number": "40",         "name": "TSEN",         "type": "input",-        "description": "Temperature sense input for highest temperature of power stages (maximum sensed: 127.9 \u00b0C); connects to TAO/FAULT pin of TI smart power stages; over-temperature fault threshold 125 \u00b0C default with 15 \u00b0C hysteresis."+        "description": "Temperature sense input for highest temperature of power stages (maximum sensed: 127.9 °C); connects to TAO/FAULT pin of TI smart power stages; over-temperature fault threshold 125 °C default with 15 °C hysteresis."       },       {         "number": "41",@@ -331,6 +331,46 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "tps53647rtat.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.0,+          6.0,+          1.0+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "e5b4286c2329085d9ef7f90d5eb5bf41a435241ecc1baaf1383823b6d6a946ae",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "tps53647rtat-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.0,+          6.0,+          1.0+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "4368219c7ef6e3305679b86df8474ddce5a88a1c16441d5fa9394e61db99f9d9",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   }-}\ No newline at end of file+}
page.json+42−2
@@ -316,7 +316,47 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "tps53647rtat.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.0,+          6.0,+          1.0+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "e5b4286c2329085d9ef7f90d5eb5bf41a435241ecc1baaf1383823b6d6a946ae",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "tps53647rtat-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.0,+          6.0,+          1.0+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "4368219c7ef6e3305679b86df8474ddce5a88a1c16441d5fa9394e61db99f9d9",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   },   "metadata": {     "specs": {@@ -364,4 +404,4 @@     "public": true   },   "updated_at": "2026-09-25T12:05:25.172Z"-}\ No newline at end of file+}