component
TPS51396ARJER
Public Made by Adomby adom
Texas Instruments DC-DC Converters, QFN-20-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+58@@ -0,0 +1,58 @@+# TPS51396ARJER++**Texas Instruments** · DC-DC Converters · QFN-20-EP(3x3)++TPS51396ARJER from Texas Instruments, in a QFN-20-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | BST | power_in | Supply input for gate drive voltage of high-side MOSFET; connect 0.1 μF bootstrap capacitor between BST and SW. |+| 2 | VIN | power_in | Input voltage supply pin for control circuitry rated 4.5V to 24V; connect input decoupling capacitors between VIN and GND. |+| 3 | VIN | power_in | Input voltage supply pin for control circuitry rated 4.5V to 24V; connect input decoupling capacitors between VIN and GND. |+| 4 | VIN | power_in | Input voltage supply pin for control circuitry rated 4.5V to 24V; connect input decoupling capacitors between VIN and GND. |+| 5 | VIN | power_in | Input voltage supply pin for control circuitry rated 4.5V to 24V; connect input decoupling capacitors between VIN and GND. |+| 6 | SW | output | Switch node terminal; connect output inductor to this pin. |+| 7 | GND | power_in | Power ground terminal for controller circuit and internal circuitry. |+| 8 | GND | power_in | Power ground terminal for controller circuit and internal circuitry. |+| 9 | PGOOD | output | Open drain power good indicator asserted low if output voltage out of threshold, overvoltage, thermal shutdown, EN shutdown, or soft start condition. |+| 10 | NC | unconnected | Not connected; can be connected to GND plane for improved thermal performance. |+| 11 | SS | input | Soft-start time selection pin; external capacitor sets timing with 1.3 ms default if not connected. |+| 12 | EN | input | Digital input enable pin to turn on/off buck converter with internal pull-down current when left open. |+| 13 | AGND | power_in | Analog ground; connect to GND plane with short trace. |+| 14 | FB | input | Converter feedback input connected to center tap of resistor divider between output voltage and AGND. |+| 15 | MODE | input | Light load operation mode selection pin; connect to resistor divider from VCC and AGND per table 7-1. |+| 16 | NC | unconnected | Not connected; can be connected to GND plane for improved thermal performance. |+| 17 | VCC | power_in | 5.0V internal LDO output supplying voltage to internal circuitry and gate driver; bypass with 1 μF capacitor. |+| 18 | GND | power_in | Power ground terminal for controller circuit and internal circuitry. |+| 19 | SW | output | Switch node terminal; connect output inductor to this pin. |+| 20 | SW | output | Switch node terminal; connect output inductor to this pin. |+| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-20-EP(3x3) |+| Category | Power Management (PMIC) |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `TPS51396ARJER`+- Footprint: `Package_DFN_QFN:UQFN-20-1EP_3x3mm_P0.4mm_EP1.85x1.85mm`+- 3D model: QFN-20-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `tps51396arjer-etched.step` / `tps51396arjer-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps51396arjer.step` / `tps51396arjer.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps51396a) (33 pp, sha256 `886c9ef21f4b86f1`, retrieved 2026-10-03, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps51396arjer-datasheet.pdf)
page.jsonadded+239@@ -0,0 +1,239 @@+{+ "slug": "tps51396arjer",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, QFN-20-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "tps51396arjer",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps51396arjer.kicad_sym",+ "tps51396arjer.kicad_mod",+ "tps51396arjer.glb",+ "tps51396arjer.step",+ "tps51396arjer.lbr",+ "docs/hero.png",+ "docs/tps51396arjer-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps51396arjer-hero.glb",+ "tps51396arjer-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS51396ARJER",+ "manufacturer": "Texas Instruments",+ "package": "QFN-20-EP(3x3)",+ "pin_count": 21,+ "category": "Power Management (PMIC)",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps51396a",+ "parts": {+ "symbol": "tps51396arjer.kicad_sym",+ "footprint": "tps51396arjer.kicad_mod",+ "model_3d": "tps51396arjer-hero.glb",+ "model_3d_plain": "tps51396arjer.glb",+ "model_3d_step": "tps51396arjer-etched.step",+ "model_3d_step_plain": "tps51396arjer.step",+ "lbr": "tps51396arjer.lbr"+ },+ "distributor_links": {+ "lcsc": 3032872,+ "digikey": "296-TPS51396ARJERTR-ND",+ "mouser": "595-TPS51396ARJER"+ },+ "distributor_check": {+ "checked_at": "2026-10-03T00:39:37Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-TPS51396ARJERTR-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS51396ARJER",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "BST",+ "type": "power_in",+ "description": "Supply input for gate drive voltage of high-side MOSFET; connect 0.1 μF bootstrap capacitor between BST and SW."+ },+ {+ "number": "2",+ "name": "VIN",+ "type": "power_in",+ "description": "Input voltage supply pin for control circuitry rated 4.5V to 24V; connect input decoupling capacitors between VIN and GND."+ },+ {+ "number": "3",+ "name": "VIN",+ "type": "power_in",+ "description": "Input voltage supply pin for control circuitry rated 4.5V to 24V; connect input decoupling capacitors between VIN and GND."+ },+ {+ "number": "4",+ "name": "VIN",+ "type": "power_in",+ "description": "Input voltage supply pin for control circuitry rated 4.5V to 24V; connect input decoupling capacitors between VIN and GND."+ },+ {+ "number": "5",+ "name": "VIN",+ "type": "power_in",+ "description": "Input voltage supply pin for control circuitry rated 4.5V to 24V; connect input decoupling capacitors between VIN and GND."+ },+ {+ "number": "6",+ "name": "SW",+ "type": "output",+ "description": "Switch node terminal; connect output inductor to this pin."+ },+ {+ "number": "7",+ "name": "GND",+ "type": "power_in",+ "description": "Power ground terminal for controller circuit and internal circuitry."+ },+ {+ "number": "8",+ "name": "GND",+ "type": "power_in",+ "description": "Power ground terminal for controller circuit and internal circuitry."+ },+ {+ "number": "9",+ "name": "PGOOD",+ "type": "output",+ "description": "Open drain power good indicator asserted low if output voltage out of threshold, overvoltage, thermal shutdown, EN shutdown, or soft start condition."+ },+ {+ "number": "10",+ "name": "NC",+ "type": "unconnected",+ "description": "Not connected; can be connected to GND plane for improved thermal performance."+ },+ {+ "number": "11",+ "name": "SS",+ "type": "input",+ "description": "Soft-start time selection pin; external capacitor sets timing with 1.3 ms default if not connected."+ },+ {+ "number": "12",+ "name": "EN",+ "type": "input",+ "description": "Digital input enable pin to turn on/off buck converter with internal pull-down current when left open."+ },+ {+ "number": "13",+ "name": "AGND",+ "type": "power_in",+ "description": "Analog ground; connect to GND plane with short trace."+ },+ {+ "number": "14",+ "name": "FB",+ "type": "input",+ "description": "Converter feedback input connected to center tap of resistor divider between output voltage and AGND."+ },+ {+ "number": "15",+ "name": "MODE",+ "type": "input",+ "description": "Light load operation mode selection pin; connect to resistor divider from VCC and AGND per table 7-1."+ },+ {+ "number": "16",+ "name": "NC",+ "type": "unconnected",+ "description": "Not connected; can be connected to GND plane for improved thermal performance."+ },+ {+ "number": "17",+ "name": "VCC",+ "type": "power_in",+ "description": "5.0V internal LDO output supplying voltage to internal circuitry and gate driver; bypass with 1 μF capacitor."+ },+ {+ "number": "18",+ "name": "GND",+ "type": "power_in",+ "description": "Power ground terminal for controller circuit and internal circuitry."+ },+ {+ "number": "19",+ "name": "SW",+ "type": "output",+ "description": "Switch node terminal; connect output inductor to this pin."+ },+ {+ "number": "20",+ "name": "SW",+ "type": "output",+ "description": "Switch node terminal; connect output inductor to this pin."+ },+ {+ "number": "21",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Datasheet references exposed thermal pad (Pad G) in GND description but does not assign it an explic",+ "exposed pad 21 added from the footprint"+ ],+ "pages_sent": 7,+ "cost_usd": 0.1377,+ "at": "2026-10-03T00:39:18"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps51396a",+ "pages": 33,+ "sha256": "886c9ef21f4b86f1",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 21,+ "described": 21,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}