← Commit history

tps51220artvr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)

Ray ·591b1b1aa7 · ·parent 88f8087
2 files changed +98−18
package.json+56−16
@@ -53,7 +53,7 @@         "number": "1",         "name": "DRVH1",         "type": "output",-        "description": "High-side MOSFET gate driver output for channel 1; source 1.7 \u03a9, sink 1.0 \u03a9, SW1-node referenced floating driver, drive voltage corresponds to VBST1 to SW1 voltage."+        "description": "High-side MOSFET gate driver output for channel 1; source 1.7 Ω, sink 1.0 Ω, SW1-node referenced floating driver, drive voltage corresponds to VBST1 to SW1 voltage."       },       {         "number": "2",@@ -77,7 +77,7 @@         "number": "5",         "name": "PGOOD1",         "type": "output",-        "description": "Powergood window comparator output for channel 1; recommended applied voltage less than 6 V, recommended pull-up resistance 100 k\u03a9 to 1 M\u03a9."+        "description": "Powergood window comparator output for channel 1; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ."       },       {         "number": "6",@@ -89,7 +89,7 @@         "number": "7",         "name": "CSP1",         "type": "bidirectional",-        "description": "Current sense comparator (+) input for channel 1; use an RC network with X5R/X7R ceramic capacitor (0.1 \u00b5F typical) to extract voltage drop across DCR."+        "description": "Current sense comparator (+) input for channel 1; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR."       },       {         "number": "8",@@ -125,7 +125,7 @@         "number": "13",         "name": "VREF2",         "type": "power_out",-        "description": "2-V reference output; bypass to signal GND with 0.22-\u00b5F ceramic capacitance."+        "description": "2-V reference output; bypass to signal GND with 0.22-µF ceramic capacitance."       },       {         "number": "14",@@ -137,7 +137,7 @@         "number": "15",         "name": "COMP2",         "type": "input",-        "description": "Ramp compensation/loop compensation pin for channel 2; connect R (10 k\u03a9 typical, 6 k\u03a9-20 k\u03a9 range) from this pin to VREF2 for D-CAP mode ramp compensation or current-mode loop compensation."+        "description": "Ramp compensation/loop compensation pin for channel 2; connect R (10 kΩ typical, 6 kΩ-20 kΩ range) from this pin to VREF2 for D-CAP mode ramp compensation or current-mode loop compensation."       },       {         "number": "16",@@ -155,7 +155,7 @@         "number": "18",         "name": "CSP2",         "type": "bidirectional",-        "description": "Current sense comparator (+) input for channel 2; use an RC network with X5R/X7R ceramic capacitor (0.1 \u00b5F typical) to extract voltage drop across DCR."+        "description": "Current sense comparator (+) input for channel 2; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR."       },       {         "number": "19",@@ -167,7 +167,7 @@         "number": "20",         "name": "PGOOD2",         "type": "output",-        "description": "Powergood window comparator output for channel 2; recommended applied voltage less than 6 V, recommended pull-up resistance 100 k\u03a9 to 1 M\u03a9."+        "description": "Powergood window comparator output for channel 2; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ."       },       {         "number": "21",@@ -179,7 +179,7 @@         "number": "22",         "name": "VREG3",         "type": "power_out",-        "description": "Always-alive 3.3-V, 10-mA LDO output; bypass to signal GND with more than 1-\u00b5F ceramic capacitance; runs from VIN or from VREG5 when switched over to V5SW."+        "description": "Always-alive 3.3-V, 10-mA LDO output; bypass to signal GND with more than 1-µF ceramic capacitance; runs from VIN or from VREG5 when switched over to V5SW."       },       {         "number": "23",@@ -191,7 +191,7 @@         "number": "24",         "name": "DRVH2",         "type": "output",-        "description": "High-side MOSFET gate driver output for channel 2; source 1.7 \u03a9, sink 1.0 \u03a9, SW2-node referenced floating driver, drive voltage corresponds to VBST2 to SW2 voltage."+        "description": "High-side MOSFET gate driver output for channel 2; source 1.7 Ω, sink 1.0 Ω, SW2-node referenced floating driver, drive voltage corresponds to VBST2 to SW2 voltage."       },       {         "number": "25",@@ -203,13 +203,13 @@         "number": "26",         "name": "VBST2",         "type": "power_in",-        "description": "Supply input for channel-2 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 \u00b5F or greater recommended) from this pin to SW2; an optional Schottky diode from VREG5 is allowed."+        "description": "Supply input for channel-2 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW2; an optional Schottky diode from VREG5 is allowed."       },       {         "number": "27",         "name": "DRVL2",         "type": "output",-        "description": "Low-side MOSFET gate driver output for channel 2; source 1.3 \u03a9, sink 0.7 \u03a9, GND-referenced driver."+        "description": "Low-side MOSFET gate driver output for channel 2; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver."       },       {         "number": "28",@@ -221,19 +221,19 @@         "number": "29",         "name": "VREG5",         "type": "power_out",-        "description": "5-V, 100-mA LDO output; bypass to power GND with a 10-\u00b5F (min 4.7-\u00b5F) ceramic capacitor; runs from VIN, internally connected to VBST and DRVL, shuts off with EN, switches over to V5SW when 4.8 V or above is provided."+        "description": "5-V, 100-mA LDO output; bypass to power GND with a 10-µF (min 4.7-µF) ceramic capacitor; runs from VIN, internally connected to VBST and DRVL, shuts off with EN, switches over to V5SW when 4.8 V or above is provided."       },       {         "number": "30",         "name": "DRVL1",         "type": "output",-        "description": "Low-side MOSFET gate driver output for channel 1; source 1.3 \u03a9, sink 0.7 \u03a9, GND-referenced driver."+        "description": "Low-side MOSFET gate driver output for channel 1; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver."       },       {         "number": "31",         "name": "VBST1",         "type": "power_in",-        "description": "Supply input for channel-1 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 \u00b5F or greater recommended) from this pin to SW1; an optional Schottky diode from VREG5 is allowed."+        "description": "Supply input for channel-1 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW1; an optional Schottky diode from VREG5 is allowed."       },       {         "number": "32",@@ -282,6 +282,46 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "tps51220artvr.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          5.0,+          5.0,+          0.875+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "5fa713ea46b36980895812ed853577889b7cb06d275041a39b99bc0be305dc79",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "tps51220artvr-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          5.0,+          5.0,+          0.875+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "7a14d7231a748a83e13410e2ee29800896580a15f7a83f4018abb168c42ba4cb",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   }-}\ No newline at end of file+}
page.json+42−2
@@ -267,7 +267,47 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "tps51220artvr.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          5.0,+          5.0,+          0.875+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "5fa713ea46b36980895812ed853577889b7cb06d275041a39b99bc0be305dc79",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "tps51220artvr-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          5.0,+          5.0,+          0.875+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "7a14d7231a748a83e13410e2ee29800896580a15f7a83f4018abb168c42ba4cb",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   },   "metadata": {     "specs": {@@ -315,4 +355,4 @@     "public": true   },   "updated_at": "2026-09-25T12:05:08.351Z"-}\ No newline at end of file+}