component
TPS51220ARTVR
Public Made by Adomby adom
Texas Instruments DC-DC Converters, WQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
page.json+18−15@@ -38,7 +38,7 @@ "number": "1", "name": "DRVH1", "type": "output",- "description": "High-side MOSFET gate driver output for channel 1; source 1.7 \u03a9, sink 1.0 \u03a9, SW1-node referenced floating driver, drive voltage corresponds to VBST1 to SW1 voltage."+ "description": "High-side MOSFET gate driver output for channel 1; source 1.7 Ω, sink 1.0 Ω, SW1-node referenced floating driver, drive voltage corresponds to VBST1 to SW1 voltage." }, { "number": "2",@@ -62,7 +62,7 @@ "number": "5", "name": "PGOOD1", "type": "output",- "description": "Powergood window comparator output for channel 1; recommended applied voltage less than 6 V, recommended pull-up resistance 100 k\u03a9 to 1 M\u03a9."+ "description": "Powergood window comparator output for channel 1; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ." }, { "number": "6",@@ -74,7 +74,7 @@ "number": "7", "name": "CSP1", "type": "bidirectional",- "description": "Current sense comparator (+) input for channel 1; use an RC network with X5R/X7R ceramic capacitor (0.1 \u00b5F typical) to extract voltage drop across DCR."+ "description": "Current sense comparator (+) input for channel 1; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR." }, { "number": "8",@@ -110,7 +110,7 @@ "number": "13", "name": "VREF2", "type": "power_out",- "description": "2-V reference output; bypass to signal GND with 0.22-\u00b5F ceramic capacitance."+ "description": "2-V reference output; bypass to signal GND with 0.22-µF ceramic capacitance." }, { "number": "14",@@ -122,7 +122,7 @@ "number": "15", "name": "COMP2", "type": "input",- "description": "Ramp compensation/loop compensation pin for channel 2; connect R (10 k\u03a9 typical, 6 k\u03a9-20 k\u03a9 range) from this pin to VREF2 for D-CAP mode ramp compensation or current-mode loop compensation."+ "description": "Ramp compensation/loop compensation pin for channel 2; connect R (10 kΩ typical, 6 kΩ-20 kΩ range) from this pin to VREF2 for D-CAP mode ramp compensation or current-mode loop compensation." }, { "number": "16",@@ -140,7 +140,7 @@ "number": "18", "name": "CSP2", "type": "bidirectional",- "description": "Current sense comparator (+) input for channel 2; use an RC network with X5R/X7R ceramic capacitor (0.1 \u00b5F typical) to extract voltage drop across DCR."+ "description": "Current sense comparator (+) input for channel 2; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR." }, { "number": "19",@@ -152,7 +152,7 @@ "number": "20", "name": "PGOOD2", "type": "output",- "description": "Powergood window comparator output for channel 2; recommended applied voltage less than 6 V, recommended pull-up resistance 100 k\u03a9 to 1 M\u03a9."+ "description": "Powergood window comparator output for channel 2; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ." }, { "number": "21",@@ -164,7 +164,7 @@ "number": "22", "name": "VREG3", "type": "power_out",- "description": "Always-alive 3.3-V, 10-mA LDO output; bypass to signal GND with more than 1-\u00b5F ceramic capacitance; runs from VIN or from VREG5 when switched over to V5SW."+ "description": "Always-alive 3.3-V, 10-mA LDO output; bypass to signal GND with more than 1-µF ceramic capacitance; runs from VIN or from VREG5 when switched over to V5SW." }, { "number": "23",@@ -176,7 +176,7 @@ "number": "24", "name": "DRVH2", "type": "output",- "description": "High-side MOSFET gate driver output for channel 2; source 1.7 \u03a9, sink 1.0 \u03a9, SW2-node referenced floating driver, drive voltage corresponds to VBST2 to SW2 voltage."+ "description": "High-side MOSFET gate driver output for channel 2; source 1.7 Ω, sink 1.0 Ω, SW2-node referenced floating driver, drive voltage corresponds to VBST2 to SW2 voltage." }, { "number": "25",@@ -188,13 +188,13 @@ "number": "26", "name": "VBST2", "type": "power_in",- "description": "Supply input for channel-2 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 \u00b5F or greater recommended) from this pin to SW2; an optional Schottky diode from VREG5 is allowed."+ "description": "Supply input for channel-2 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW2; an optional Schottky diode from VREG5 is allowed." }, { "number": "27", "name": "DRVL2", "type": "output",- "description": "Low-side MOSFET gate driver output for channel 2; source 1.3 \u03a9, sink 0.7 \u03a9, GND-referenced driver."+ "description": "Low-side MOSFET gate driver output for channel 2; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver." }, { "number": "28",@@ -206,19 +206,19 @@ "number": "29", "name": "VREG5", "type": "power_out",- "description": "5-V, 100-mA LDO output; bypass to power GND with a 10-\u00b5F (min 4.7-\u00b5F) ceramic capacitor; runs from VIN, internally connected to VBST and DRVL, shuts off with EN, switches over to V5SW when 4.8 V or above is provided."+ "description": "5-V, 100-mA LDO output; bypass to power GND with a 10-µF (min 4.7-µF) ceramic capacitor; runs from VIN, internally connected to VBST and DRVL, shuts off with EN, switches over to V5SW when 4.8 V or above is provided." }, { "number": "30", "name": "DRVL1", "type": "output",- "description": "Low-side MOSFET gate driver output for channel 1; source 1.3 \u03a9, sink 0.7 \u03a9, GND-referenced driver."+ "description": "Low-side MOSFET gate driver output for channel 1; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver." }, { "number": "31", "name": "VBST1", "type": "power_in",- "description": "Supply input for channel-1 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 \u00b5F or greater recommended) from this pin to SW1; an optional Schottky diode from VREG5 is allowed."+ "description": "Supply input for channel-1 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW1; an optional Schottky diode from VREG5 is allowed." }, { "number": "32",@@ -310,5 +310,8 @@ "docs/tps51220artvr-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }