Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS51200QDRCRQ1

Texas Instruments · Power Management - Specialized · VSON-10-EP(3x3)

TPS51200QDRCRQ1 from Texas Instruments, in a VSON-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 REFIN input Reference input that accepts 0.5 V to 1.8 V per the recommended operating conditions, allowing tracking directly or through a resistor divider.
2 VLDOIN input Supply voltage for the LDO, with a recommended range of -0.1 V to 3.5 V and an absolute maximum of 3.6 V.
3 VO output Power output for the LDO that requires a minimum of 20 µF of capacitance with no maximum limit.
4 PGND power_in Power ground output for the LDO, with a recommended range of -0.1 V to 0.1 V relative to GND.
5 VOSNS input Voltage sense pin for the LDO that connects to the positive pin of the output capacitor or the load, with a recommended range of -0.1 V to 3.5 V.
6 REFOUT output Buffered reference output that must connect to GND through a 0.1 µF ceramic capacitor, must not be left open, and keeps total capacitance below 1 µF if a DDR-side capacitor is used.
7 EN input Enable input that connects to SLP_S3 for DDR VTT applications, and must be kept at or below the VIN voltage at all times, with a recommended range of -0.1 V to 3.5 V.
8 GND power_in Signal ground that connects to the negative pin of the output capacitor.
9 PGOOD output Open-drain output that indicates regulation, with a recommended range of -0.1 V to 3.5 V and an absolute maximum of 6.5 V.
10 VIN power_in 2.5 V or 3.3 V power supply input with a recommended supply range of 2.375 V to 3.500 V, requiring a ceramic decoupling capacitor between 1 µF and 4.7 µF.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSON-10-EP(3x3)
Category Power Management (PMIC)
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN, VLDOIN, VOSNS, REFIN -0.3 3.6 V 4
Input voltage EN -0.3 6.5 V 4
PGND to GND -0.3 0.3 V 4
Output voltage VO, REFOUT -0.3 3.6 V 4
Output voltage PGOOD -0.3 6.5 V 4
Operating junction temperature TJ 150 °C 4
Storage temperature Tstg -55 150 °C 4
Supply voltage VIN 2.375 3.5 V 4
Voltage range EN, VLDOIN, VOSNS -0.1 3.5 V 4
Voltage range REFIN 0.5 1.8 V 4
Voltage range VO, PGOOD -0.1 3.5 V 4
Voltage range REFOUT -0.1 1.8 V 4
Voltage range PGND -0.1 0.1 V 4
Operating free-air temperature TA -40 125 °C 4
Input current supply IIN 0.7 1 mA TA = 25 °C, VEN = 3.3 V, No Load 5
Shutdown current IIN(SDN) 65 80 μA TA = 25 °C, VEN = 0 V, VREFIN = 0, No Load 5
Shutdown current IIN(SDN) 200 400 μA TA = 25 °C, VEN = 0 V, VREFIN > 0.4 V, No Load 5
Supply current of VLDOIN ILDOIN 1 50 μA TA = 25 °C, VEN = 3.3 V, No Load 5
Shutdown current of VLDOIN ILDOIN(SDN) 0.1 50 μA TA = 25 °C, VEN = 0 V, No Load 5
Input current, REFIN IREFIN 1 μA VEN = 3.3 V 5
Output DC voltage, VO VVOSNS -15 15 mV VREFOUT = 1.25 V (DDR1), IO = 0 A 5
Output voltage tolerance to REFOUT VVOTOL -25 25 mV -2A < IVO < 2A 5
VO source current limit IVOSRCL 3 4.5 A With reference to REFOUT, VOSNS = 90% × VREFOUT 5
VO sink current limit IVOSNCL 3.5 5.5 A With reference to REFOUT, VOSNS = 110% × VREFOUT 5
Discharge current, VO IDSCHRG 18 25 Ω VREFIN = 0 V, VVO = 0.3 V, VEN = 0 V, TA = 25°C 5
VO PGOOD threshold lower VTH(PG) -23.5 -20 -17.5 % PGOOD window lower threshold with respect to REFOUT 5
VO PGOOD threshold upper VTH(PG) 17.5 20 23.5 % PGOOD window upper threshold with respect to REFOUT 5
Output low voltage VPGOODLOW 0.4 V ISINK = 4 mA 5
Leakage current IPGOODLK 1 μA VOSNS = VREFIN (PGOOD high impedance), PGOOD = VIN + 0.2 V 5
REFIN voltage range VREFIN 0.5 1.8 V 5
REFIN undervoltage lockout VREFINUVLO 360 390 420 mV REFIN rising 5
REFOUT voltage tolerance to VREFIN VREFOUTTOL -15 15 mV -10 mA ≤ IREFOUT ≤ 10 mA, 0.6 V ≤ VREFIN ≤ 1.25 V 5
REFOUT voltage tolerance to VREFIN VREFOUTTOL -12 12 mV -1 mA ≤ IREFOUT ≤ 1 mA, 0.6 V ≤ VREFIN ≤ 1.25 V 5
REFOUT source current limit IREFOUTSRCL 10 40 mA VREFOUT = 0.5 V 5
REFOUT sink current limit IREFOUTSNCL 10 40 mA VREFOUT = 1.5 V 5
VIN UVLO threshold VVINUVVIN 2.2 2.3 2.375 V Wake up, TA = 25°C 5
High-level input voltage Enable VENIH 1.7 V 5
Low-level input voltage Enable VENIL 0.3 V 5
Logic input leakage current EN IENLEAK -1 1 μA TA = 25°C 5
PGOOD startup delay TPGSTUPDLY 2 ms Startup rising edge, VOSNS within 15% of REFOUT 6
PGOOD bad delay TPBADDLY 10 μs VOSNS is outside of the ±20% PGOOD window 6
REFIN undervoltage lockout hysteresis VREFINUVHYS 20 mV 5
PGOOD hysteresis 5 % 5
Hysteresis (VIN UVLO) 50 mV 5
Hysteresis voltage Enable VENYST 0.5 V 5
Thermal shutdown threshold TSON 150 °C Shutdown temperature 5
Thermal shutdown hysteresis 25 °C 5
Junction-to-ambient thermal resistance RθJA 52.7 °C/W 4
Junction-to-case (top) thermal resistance RθJCtop 63.9 °C/W 4
Junction-to-board thermal resistance RθJB 28.4 °C/W 4
Junction-to-top characterization parameter ψJT 3.5 °C/W 4
Junction-to-board characterization parameter ψJB 28.6 °C/W 4
Junction-to-case (bottom) thermal resistance RθJCbot 16.1 °C/W 4

CAD (Adom-generated)

  • Symbol: TPS51200QDRCRQ1
  • Footprint: Adom_Gen:Texas_Instruments_TPS51200_efd923
  • 3D model: generated to fit the land (STEP)
  • 3D model files: tps51200qdrcrq1-etched.step / tps51200qdrcrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps51200qdrcrq1.step / tps51200qdrcrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (38 pp, sha256 6258a3b10816e7f9, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.

Datasheet PDF