← Commit history

Initial commit: component/tps40170qrgyrq1

Ray ·673ee71c54 ·
2 files changed +280
README.mdadded+58
@@ -0,0 +1,58 @@+# TPS40170QRGYRQ1++**Texas Instruments** · AC-DC Controllers & Regulators · VQFN-20-EP(3.7x4.7)++TPS40170QRGYRQ1 from Texas Instruments, in a VQFN-20-EP(3.7x4.7). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | ENABLE | input | Enable pin that must be high to enable the device; pull below VDIS (100 mV) to disable. |+| 2 | SYNC | bidirectional | Synchronization pin used for frequency synchronization; output in primary mode, input in secondary 0° or 180° mode. |+| 3 | M/S | input | Primary/secondary mode selector pin; tie to VIN for primary mode, tie to AGND or leave floating for secondary mode. |+| 4 | RT | input | Resistor from this pin to AGND sets the oscillator frequency from 100 kHz to 600 kHz; required in all modes. |+| 5 | SS | input | Soft-start pin; capacitor from this pin to AGND sets the soft-start time and is used for fault timing. |+| 6 | TRK | input | Tracking input for output voltage tracking; the lesser of VTRK and the internal 600 mV reference sets the output voltage. |+| 7 | FB | input | Feedback input to the error amplifier; output voltage is fed back through a resistor divider network. |+| 8 | COMP | output | Output of the internal error amplifier; compensation network is connected from this pin to the FB pin. |+| 9 | AGND | power_in | Analog signal ground; must be electrically connected to PGND externally at a single point. |+| 10 | VDD | power_out | 3.3 V regulated output; 0.1 µF to 1 µF ceramic bypass capacitor must be connected to AGND close to this pin. |+| 11 | PGOOD | output | Open-drain power-good indicator output; 10 kΩ pullup resistor to VDD recommended; pulls low when out of regulation or faults detected. |+| 12 | ILIM | input | Overcurrent limit pin; resistor from this pin to PGND sets the overcurrent protection threshold based on low-side FET sensing. |+| 13 | PGND | power_in | Power ground for gate driver return path; must externally connect to AGND at a single point. |+| 14 | LDRV | output | Gate driver output for low-side FET; resistor from this pin to PGND also sets the multiplier (3, 7, or 15) for short-circuit protection. |+| 15 | VBP | power_out | 8 V regulated output for gate driver; 1 µF to 10 µF ceramic bypass capacitor must be connected from this pin to PGND. |+| 16 | SW | input | Switching node connection point for the synchronous buck converter; used for high-side and low-side FET current sensing for overcurrent and short-circuit protection. |+| 17 | HDRV | output | Gate driver output for the high-side FET; referenced to SW and switches between BOOT and SW. |+| 18 | BOOT | output | Boot-capacitor node for high-side FET gate driver; bootstrap capacitor (0.1 µF to 0.22 µF) connected from this pin to SW. |+| 19 | VIN | power_in | Input voltage for the controller and DC-DC converter (4.5 V to 60 V); 1 µF bypass capacitor from this pin to AGND required and placed close to pin. |+| 20 | UVLO | input | Undervoltage lockout pin; resistor divider from VIN to AGND sets the UVLO threshold; 1 nF bypass capacitor to AGND required. |+| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-20-EP(3.7x4.7) |+| Category | Power Supply Chip |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `TPS40170QRGYRQ1`+- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x5mm_P0.5mm_EP2.65x3.65mm`+- 3D model: VQFN-20-EP(3.7x4.7) (KiCad packages3D, STEP)+- 3D model files: `tps40170qrgyrq1-etched.step` / `tps40170qrgyrq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps40170qrgyrq1.step` / `tps40170qrgyrq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps40170-q1) (53 pp, sha256 `0fe03952f1a1b899`, retrieved 2026-09-18, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps40170qrgyrq1-datasheet.pdf)
page.jsonadded+222
@@ -0,0 +1,222 @@+{+  "slug": "tps40170qrgyrq1",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments AC-DC Controllers & Regulators, VQFN-20-EP(3.7x4.7). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power supply chip",+    "tps40170qrgyrq1",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps40170qrgyrq1.kicad_sym",+    "tps40170qrgyrq1.kicad_mod",+    "tps40170qrgyrq1.glb",+    "tps40170qrgyrq1.step",+    "tps40170qrgyrq1.lbr",+    "docs/hero.png",+    "docs/tps40170qrgyrq1-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS40170QRGYRQ1",+    "manufacturer": "Texas Instruments",+    "package": "VQFN-20-EP(3.7x4.7)",+    "pin_count": 21,+    "category": "Power Supply Chip",+    "subcategory": "AC-DC Controllers & Regulators",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps40170-q1",+    "parts": {+      "symbol": "tps40170qrgyrq1.kicad_sym",+      "footprint": "tps40170qrgyrq1.kicad_mod",+      "model_3d": "tps40170qrgyrq1-etched.glb",+      "model_3d_plain": "tps40170qrgyrq1.glb",+      "model_3d_step": "tps40170qrgyrq1-etched.step",+      "model_3d_step_plain": "tps40170qrgyrq1.step",+      "lbr": "tps40170qrgyrq1.lbr"+    },+    "distributor_links": {+      "lcsc": "C181238"+    },+    "pins": [+      {+        "number": "1",+        "name": "ENABLE",+        "type": "input",+        "description": "Enable pin that must be high to enable the device; pull below VDIS (100 mV) to disable."+      },+      {+        "number": "2",+        "name": "SYNC",+        "type": "bidirectional",+        "description": "Synchronization pin used for frequency synchronization; output in primary mode, input in secondary 0° or 180° mode."+      },+      {+        "number": "3",+        "name": "M/S",+        "type": "input",+        "description": "Primary/secondary mode selector pin; tie to VIN for primary mode, tie to AGND or leave floating for secondary mode."+      },+      {+        "number": "4",+        "name": "RT",+        "type": "input",+        "description": "Resistor from this pin to AGND sets the oscillator frequency from 100 kHz to 600 kHz; required in all modes."+      },+      {+        "number": "5",+        "name": "SS",+        "type": "input",+        "description": "Soft-start pin; capacitor from this pin to AGND sets the soft-start time and is used for fault timing."+      },+      {+        "number": "6",+        "name": "TRK",+        "type": "input",+        "description": "Tracking input for output voltage tracking; the lesser of VTRK and the internal 600 mV reference sets the output voltage."+      },+      {+        "number": "7",+        "name": "FB",+        "type": "input",+        "description": "Feedback input to the error amplifier; output voltage is fed back through a resistor divider network."+      },+      {+        "number": "8",+        "name": "COMP",+        "type": "output",+        "description": "Output of the internal error amplifier; compensation network is connected from this pin to the FB pin."+      },+      {+        "number": "9",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog signal ground; must be electrically connected to PGND externally at a single point."+      },+      {+        "number": "10",+        "name": "VDD",+        "type": "power_out",+        "description": "3.3 V regulated output; 0.1 µF to 1 µF ceramic bypass capacitor must be connected to AGND close to this pin."+      },+      {+        "number": "11",+        "name": "PGOOD",+        "type": "output",+        "description": "Open-drain power-good indicator output; 10 kΩ pullup resistor to VDD recommended; pulls low when out of regulation or faults detected."+      },+      {+        "number": "12",+        "name": "ILIM",+        "type": "input",+        "description": "Overcurrent limit pin; resistor from this pin to PGND sets the overcurrent protection threshold based on low-side FET sensing."+      },+      {+        "number": "13",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground for gate driver return path; must externally connect to AGND at a single point."+      },+      {+        "number": "14",+        "name": "LDRV",+        "type": "output",+        "description": "Gate driver output for low-side FET; resistor from this pin to PGND also sets the multiplier (3, 7, or 15) for short-circuit protection."+      },+      {+        "number": "15",+        "name": "VBP",+        "type": "power_out",+        "description": "8 V regulated output for gate driver; 1 µF to 10 µF ceramic bypass capacitor must be connected from this pin to PGND."+      },+      {+        "number": "16",+        "name": "SW",+        "type": "input",+        "description": "Switching node connection point for the synchronous buck converter; used for high-side and low-side FET current sensing for overcurrent and short-circuit protection."+      },+      {+        "number": "17",+        "name": "HDRV",+        "type": "output",+        "description": "Gate driver output for the high-side FET; referenced to SW and switches between BOOT and SW."+      },+      {+        "number": "18",+        "name": "BOOT",+        "type": "output",+        "description": "Boot-capacitor node for high-side FET gate driver; bootstrap capacitor (0.1 µF to 0.22 µF) connected from this pin to SW."+      },+      {+        "number": "19",+        "name": "VIN",+        "type": "power_in",+        "description": "Input voltage for the controller and DC-DC converter (4.5 V to 60 V); 1 µF bypass capacitor from this pin to AGND required and placed close to pin."+      },+      {+        "number": "20",+        "name": "UVLO",+        "type": "input",+        "description": "Undervoltage lockout pin; resistor divider from VIN to AGND sets the UVLO threshold; 1 nF bypass capacitor to AGND required."+      },+      {+        "number": "21",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Package discrepancy: The MPN TPS40170QRGYRQ1 is specified in the datasheet as a VQFN-20 RGY package ",+          "exposed pad 21 added from the footprint"+        ],+        "pages_sent": 53,+        "cost_usd": 0.4846,+        "at": "2026-09-18T02:05:58"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps40170-q1",+        "pages": 53,+        "sha256": "0fe03952f1a1b899",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 21,+        "described": 21,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file