← Commit history

Initial commit: component/tps2h160bqpwprq1

Ray ·9775ab58af ·
2 files changed +252
README.mdadded+54
@@ -0,0 +1,54 @@+# TPS2H160BQPWPRQ1++**Texas Instruments** · Power Distribution Switches · HTSSOP-16-EP++TPS2H160BQPWPRQ1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | IN1 | input | Logic input control for channel-1 activation (VIH ≥ 2 V, VIL ≤ 0.8 V); internal pulldown resistor to GND. |+| 2 | IN2 | input | Logic input control for channel-2 activation (VIH ≥ 2 V, VIL ≤ 0.8 V); internal pulldown resistor to GND. |+| 3 | DIAG_EN | input | Enable/disable pin for diagnostic functions; internal pulldown resistor, logic levels VIH ≥ 2 V / VIL ≤ 0.8 V. |+| 4 | FAULT | output | Global open-drain fault report (OR of both channels' fault conditions); pulled low (VOL ≤ 0.2 V at IFAULT = 2 mA) when a fault occurs, requires external 3.3 V or 5 V pullup, version B only. |+| 5 | SEL | input | Current-sense channel-selection input that multiplexes the shared CS output between channel 1 (SEL = 0) and channel 2 (SEL = 1); internal pulldown. |+| 6 | CS | output | Current-sense analog output that sources 1/K(CS) (K(CS) = 290 typ) of the selected channel's load current into an external resistor, producing a 0-4 V linear signal, and reports faults by pulling up to VCS(H) (4.5-6.5 V). |+| 7 | CL | input | Adjustable current-limit set pin; connect an external resistor to set the current-limit threshold (ICL(th) with K(CL) = 2500 typ), or connect directly to device GND to use the fixed internal current limit (ICL(int), 9-15 A). |+| 8 | GND | power_in | Device ground reference pin; can source/sink current up to -100/250 mA for t < 2 minutes (Absolute Maximum Ratings). |+| 9 | THER | input | Thermal-shutdown behavior control input; internal pulldown, THER low selects auto-retry mode and THER high selects latch-off mode after thermal shutdown. |+| 10 | NC | unconnected | No internal connection. |+| 11 | OUT2 | output | High-side switch output for channel 2, connected to the load; combined with pin 12 for the channel-2 output. |+| 12 | OUT2 | output | High-side switch output for channel 2, connected to the load; combined with pin 11 for the channel-2 output. |+| 13 | VS | power_in | Power-supply input pin, operating range 4 V to 40 V nominal (3.4 V turn-on to 40 V max per front page), 48 V max for t < 400 ms; combined with pin 14. |+| 14 | VS | power_in | Power-supply input pin, operating range 4 V to 40 V nominal, 48 V max for t < 400 ms; combined with pin 13. |+| 15 | OUT1 | output | High-side switch output for channel 1, connected to the load; combined with pin 16 for the channel-1 output. |+| 16 | OUT1 | output | High-side switch output for channel 1, connected to the load; combined with pin 15 for the channel-1 output. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-16-EP |+| Category | Power Supply Chip |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `TPS2H160BQPWPRQ1`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `tps2h160bqpwprq1-etched.step` / `tps2h160bqpwprq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps2h160bqpwprq1.step` / `tps2h160bqpwprq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps2h160-q1) (40 pp, sha256 `3efb7de2cb9fa29f`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps2h160bqpwprq1-datasheet.pdf)
page.jsonadded+198
@@ -0,0 +1,198 @@+{+  "slug": "tps2h160bqpwprq1",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Power Distribution Switches, HTSSOP-16-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power supply chip",+    "tps2h160bqpwprq1",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps2h160bqpwprq1.kicad_sym",+    "tps2h160bqpwprq1.kicad_mod",+    "tps2h160bqpwprq1.glb",+    "tps2h160bqpwprq1.step",+    "tps2h160bqpwprq1.lbr",+    "docs/hero.png",+    "docs/tps2h160bqpwprq1-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS2H160BQPWPRQ1",+    "manufacturer": "Texas Instruments",+    "package": "HTSSOP-16-EP",+    "pin_count": 17,+    "category": "Power Supply Chip",+    "subcategory": "Power Distribution Switches",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps2h160-q1",+    "parts": {+      "symbol": "tps2h160bqpwprq1.kicad_sym",+      "footprint": "tps2h160bqpwprq1.kicad_mod",+      "model_3d": "tps2h160bqpwprq1-etched.glb",+      "model_3d_plain": "tps2h160bqpwprq1.glb",+      "model_3d_step": "tps2h160bqpwprq1-etched.step",+      "model_3d_step_plain": "tps2h160bqpwprq1.step",+      "lbr": "tps2h160bqpwprq1.lbr"+    },+    "distributor_links": {+      "lcsc": "C2680441"+    },+    "pins": [+      {+        "number": "1",+        "name": "IN1",+        "type": "input",+        "description": "Logic input control for channel-1 activation (VIH ≥ 2 V, VIL ≤ 0.8 V); internal pulldown resistor to GND."+      },+      {+        "number": "2",+        "name": "IN2",+        "type": "input",+        "description": "Logic input control for channel-2 activation (VIH ≥ 2 V, VIL ≤ 0.8 V); internal pulldown resistor to GND."+      },+      {+        "number": "3",+        "name": "DIAG_EN",+        "type": "input",+        "description": "Enable/disable pin for diagnostic functions; internal pulldown resistor, logic levels VIH ≥ 2 V / VIL ≤ 0.8 V."+      },+      {+        "number": "4",+        "name": "FAULT",+        "type": "output",+        "description": "Global open-drain fault report (OR of both channels' fault conditions); pulled low (VOL ≤ 0.2 V at IFAULT = 2 mA) when a fault occurs, requires external 3.3 V or 5 V pullup, version B only."+      },+      {+        "number": "5",+        "name": "SEL",+        "type": "input",+        "description": "Current-sense channel-selection input that multiplexes the shared CS output between channel 1 (SEL = 0) and channel 2 (SEL = 1); internal pulldown."+      },+      {+        "number": "6",+        "name": "CS",+        "type": "output",+        "description": "Current-sense analog output that sources 1/K(CS) (K(CS) = 290 typ) of the selected channel's load current into an external resistor, producing a 0-4 V linear signal, and reports faults by pulling up to VCS(H) (4.5-6.5 V)."+      },+      {+        "number": "7",+        "name": "CL",+        "type": "input",+        "description": "Adjustable current-limit set pin; connect an external resistor to set the current-limit threshold (ICL(th) with K(CL) = 2500 typ), or connect directly to device GND to use the fixed internal current limit (ICL(int), 9-15 A)."+      },+      {+        "number": "8",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground reference pin; can source/sink current up to -100/250 mA for t < 2 minutes (Absolute Maximum Ratings)."+      },+      {+        "number": "9",+        "name": "THER",+        "type": "input",+        "description": "Thermal-shutdown behavior control input; internal pulldown, THER low selects auto-retry mode and THER high selects latch-off mode after thermal shutdown."+      },+      {+        "number": "10",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection."+      },+      {+        "number": "11",+        "name": "OUT2",+        "type": "output",+        "description": "High-side switch output for channel 2, connected to the load; combined with pin 12 for the channel-2 output."+      },+      {+        "number": "12",+        "name": "OUT2",+        "type": "output",+        "description": "High-side switch output for channel 2, connected to the load; combined with pin 11 for the channel-2 output."+      },+      {+        "number": "13",+        "name": "VS",+        "type": "power_in",+        "description": "Power-supply input pin, operating range 4 V to 40 V nominal (3.4 V turn-on to 40 V max per front page), 48 V max for t < 400 ms; combined with pin 14."+      },+      {+        "number": "14",+        "name": "VS",+        "type": "power_in",+        "description": "Power-supply input pin, operating range 4 V to 40 V nominal, 48 V max for t < 400 ms; combined with pin 13."+      },+      {+        "number": "15",+        "name": "OUT1",+        "type": "output",+        "description": "High-side switch output for channel 1, connected to the load; combined with pin 16 for the channel-1 output."+      },+      {+        "number": "16",+        "name": "OUT1",+        "type": "output",+        "description": "High-side switch output for channel 1, connected to the load; combined with pin 15 for the channel-1 output."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Pin diagram labeling discrepancy on PAGE 3: The diagram labeled 'TPS2H160-Q1 Version B Top View' sho; Version comparison consistency: The Device Comparison Table on PAGE 3 states 'TPS2H160-Q1 Version B ",+          "exposed pad 17 added from the footprint"+        ],+        "pages_sent": 40,+        "cost_usd": 0.4372,+        "at": "2026-09-23T04:17:47"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps2h160-q1",+        "pages": 40,+        "sha256": "3efb7de2cb9fa29f",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file