main
History Download
Ray Publish 0.1.0 4eb9ddd

TPS26612DDFR

Texas Instruments · LED Drivers · TSOT-23-8

TPS26612DDFR from Texas Instruments, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Reference ground for all internal voltages; connect to GND of the ±Vs supply.
2 MODE input MODE selection pin for overload response; sets current limit to IOL, 2 × IOL, or 2 × IOL with extended IOL expiry time (GND, open, or 180 kΩ to GND), with a 0 to 3 V recommended voltage range.
3 -Vs power_in Negative supply for dual supply configurations (-20 V to 0 V recommended); connect to GND when used in a single supply configuration.
4 IN passive Signal/power input, rated -50 V to 50 V recommended (±55 V absolute maximum).
5 OUT passive Signal/power output, rated -50 V to 50 V recommended (±55 V absolute maximum).
6 +Vs power_in Positive supply for powering the device, 0 to 30 V recommended (32 V absolute maximum).
7 EN input Enable control for the TPS26612: pull EN low to turn off the device; it has an internal pullup and can be left floating to enable the device (0 to 5 V recommended).
8 SGOOD output Signal good indicator that is low in normal operating condition and goes high when outside it; it can drive an external LED, with sourcing current derived from +Vs.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TSOT-23-8
Category Nixie Tube Driver/LED Driver
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
IN, OUT, IN-OUT voltage -55 55 V 4
SGOOD, EN, MODE, VSNS voltage -0.3 5.5 V 4
+Vs voltage +Vs -0.3 32 V 4
-Vs voltage -Vs -22 0.3 V 4
SGOOD current ISGOOD 200 µA 4
Operating junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
ESD HBM V(ESD) -2000 2000 V HBM, all pins 4
ESD CDM V(ESD) -750 750 V CDM, all pins 4
IN, OUT voltage -50 50 V 4
+Vs supply voltage +Vs 0 30 V 4
-Vs supply voltage -Vs -20 0 V 4
EN, SGOOD, VSNS voltage 0 5 V 4
MODE voltage 0 3 V 4
Operating junction temperature TJ -40 125 °C 4
Junction-to-ambient thermal resistance RθJA 117.8 °C/W DDF SOT-23-THN, 8 pins 4
Junction-to-case (top) thermal resistance RθJC(top) 57.6 °C/W 4
Junction-to-board thermal resistance RθJB 40.2 °C/W 4
Junction-to-top characterization parameter ΨJT 2.2 °C/W 4
Junction-to-board characterization parameter ΨJB 40 °C/W 5
IN signal voltage V(IN) -50 50 V 5
Sum of leakage from IN and OUT to GND, normal operation IQ -0.1 0.1 µA (-Vs) < VIN, VOUT < (+Vs, 0.35 V) 5
Sum of leakage from IN and OUT to GND, near +Vs IQ 1 µA (+Vs, 0.35 V) < VIN, VOUT < +Vs 5
Leakage to -Vs during fault, percent of loop current IQFLT 20 % VIN > +Vs, Current Limit Operation 5
Bipolar current limit I(OL) 25 32 40 mA V(IN)-V(OUT) = ±1 V, -Vs connected to negative supply; printed ±25/±32/±40 5
Unipolar current limit I(OL) 25 32 40 mA V(IN)-V(OUT) = +1 V, -Vs connected to GND 5
Transient pulse over current limit I(OL_Pulse) 50 60 72 mA V(IN)-V(OUT) = +1.5 V, MODE = Floating 5
Fast-trip current limit I(FASTRIP) 65 165 mA MODE = GND; printed ±65 / ±165 5
Fast-trip current limit I(FASTRIP) 140 275 mA MODE = Floating or 180 kΩ to GND; printed ±140 / ±275 5
Off-state leakage IN+OUT (source) IOff-Lkg-IN + IOff-Lkg-OUT -9.75 -5.25 µA -12.5 V < VIN < 12.5 V; VOUT = 0 V; EN = Low; +Vs = 15 V; -Vs = -15 V 5
Off-state leakage from IN pin (source) IOff-Lkg-IN -6 -1 µA -12.5 V < VIN < 12.5 V; VOUT = 0 V; EN = Low; +Vs = 15 V; -Vs = -15 V 5
Off-state leakage from OUT pin (source) IOff-Lkg-OUT -6 -1 µA -12.5 V < VOUT < 12.5 V; VIN = 0 V; EN = Low; +Vs = 15 V; -Vs = -15 V 5
OUT overvoltage threshold, rising (offset above +Vs) VOUT_OVLO 1 1.5 V TPS26612 only; printed (+Vs)+1 to (+Vs)+1.50 5
OUT overvoltage hysteresis VOUT_OVLO_hyst 30 75 mV 5
OUT/IN undervoltage threshold, falling (offset from -Vs) VO/I_UVLO -0.4 -0.2 V TPS26610/11/12 only; printed (-Vs)-0.40 to (-Vs)-0.20 5
OUT/IN undervoltage hysteresis VO/I_UVLO_hyst 30 75 mV TPS26610/11/12 Only 6
+Vs supply operating voltage V(+Vs) 4 30 V TPS26612 only 6
-Vs supply operating voltage V(-Vs) -20 0 V 6
Difference between +Vs and -Vs Vs_DIFF 3 50 V 6
Current from +Vs to GND, normal operation I(+Vs) 1.07 1.65 mA SGOOD = Floating 6
Current from +Vs to GND, fault operation I(+Vs) 1.2 1.75 mA SGOOD = Floating 6
Current sinked by -Vs supply from GND I(-Vs) 0.2 mA 6
OFF state supply current IVS_OFF 0.27 mA EN = Low (TPS26611/12/14 only) 6
IN to OUT total ON resistance RON 4.8 7.5 12.5 Ω -40 ℃ < T < 125 ℃, I(IN) < Overload Current 6
EN leakage current (sink) I(EN_LKG) 10 µA V(EN) = 5.5 V 6
EN leakage current (source) I(EN_LKG) -10 µA V(EN) = 0 V 6
EN open circuit voltage V(EN) 2.1 2.5 V I(EN) = -0.1 µA 6
EN rising threshold V(ENR) 1.72 V 6
EN falling threshold V(ENF) 1 V 6
SGOOD output level, HIGH VOH_SGOOD 2 3 V (+Vs) > 2.5 V, 0 mA < ISGOOD < 1 mA 7
SGOOD pull down impedance RSGOOD 6.3 kΩ 0 µA < ISGOOD < 200 µA 7
MODE source current I(MODE) 1.55 2 2.4 µA 7
Mode selection resistor RMODE 180 kΩ 7
Thermal shutdown threshold, rising T(TSD) 160 °C 7
Thermal shutdown hysteresis T(TSDHyst) 11 °C 7
Input small signal bandwidth BW 10 kHz -25 mA < IIN < 25 mA, ΔIIN = 1 mApp at 1 kΩ 7
Turn ON delay with Vs supply tON_dly 120 µs Delay from +Vs/-Vs supply applied to FET on, EN = Floating 7
Turn OFF delay with Vs supply tOFF_dly 10 µs Delay from +Vs/-Vs supply removed to FET off, EN = Floating 7
Turn ON delay with EN pin tON_EN_dly 120 µs +Vs/-Vs supply present, Delay from EN HIGH to FET on 7
Turn OFF delay with EN pin tOFF_EN_dly 10 µs +Vs/-Vs supply present, Delay from EN LOW to FET off 7
Overload current limit response time tOL 30 55 µs Load transient from 20 mA to 50 mA. Time from Load Transient to Current coming within 20% of IOL. 7
Pulse overload current limit response time tOL_PULSE 20 50 µs Load transient from 20 mA to 80 mA. Time from Load Transient to Current coming within 20% of IOL_Pulse 7
Fast-trip response time tFASTRIP 5 µs MODE = GND, Current exceeding 120mA to FET off 7
SGOOD deglitch delay, assertion TSG_Deglitch 685 µs Deglitch delay during SGOOD assertion 7
SGOOD deglitch delay, de-assertion TSG_Deglitch 1.3 ms Deglitch delay during SGOOD de-assertion 7
OUT OVLO cutoff detection time tOUT_OV_CUT 1 5 µs V(OUT) ↑ 100 mV above VOUT_OVLO to FET OFF 7
OUT or IN UVLO cutoff detection time tO/I_UV_CUT 1 5 µs OUT/IN ↓100 mV below VO/I_UVLO to FET OFF, TPS26610/11/12 Only 7
OUT cutoff recovery time tOUT_CUT_Rec 21 µs V(OUT) ↓ 100 mV below VOUT_OVLO_hyst to FET ON 8
IN or OUT cutoff recovery time tO/I_CUT_Rec 23.5 µs OUT/IN ↑100 mV above VO/I_UVLO_hyst to FET ON, TPS26610/11/12 Only 8
Overload current limit expiry time tOL_Expiry 100 ms Load transient from 20 mA to 50 mA 8
Pulse overload current expiry tOL_Pulse_Expiry 50 ms Load transient from 20 mA to 100 mA 8
IOL < I < IOL_PULSE expiry timer tOL_Extend 5 s 8
Auto retry timer 1 tRETRY1 0.8 s 8
Auto retry timer 2 tRETRY2 1.6 s 8
Auto retry disabled time tAR_dis 5 s TPS26612 only 8

CAD (KiCad official)

  • Symbol: TPS26612DDFR
  • Footprint: Package_TO_SOT_SMD:TSOT-23-8
  • 3D model: TSOT-23-8 (KiCad packages3D, STEP)
  • 3D model files: tps26612ddfr-etched.step / tps26612ddfr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps26612ddfr.step / tps26612ddfr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (45 pp, sha256 22fc9c245d7926dd, retrieved 2026-10-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF