component
TPS26601RHFT
Public Made by Adomby adom
Texas Instruments Global Sourcing Parts, VQFN-24-EP(4x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS26601RHFT
Texas Instruments · Global Sourcing Parts · VQFN-24-EP(4x5)
TPS26601RHFT from Texas Instruments, in a VQFN-24-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 2 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 3 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 4 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 5 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 6 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 7 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 8 | IN | power_in | Power input and supply voltage of the device; recommended input operating range is 4.2 V to 60 V (Recommended Operating Conditions). |
| 9 | IN | power_in | Power input and supply voltage of the device; recommended input operating range is 4.2 V to 60 V (Recommended Operating Conditions). |
| 10 | UVLO | input | Input for setting the programmable undervoltage lockout threshold; an undervoltage event turns off the internal FET and asserts FLT, and connecting UVLO to RTN selects the internal default threshold. |
| 11 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 12 | OVP | input | Input for setting the programmable overvoltage protection threshold (TPS26600/1 only); an overvoltage event turns off the internal FET and asserts FLT, and connecting OVP to RTN selects the internal default threshold. |
| 13 | MODE | input | Mode selection pin for overload fault response, configured per the Device Functional Modes section. |
| 14 | SHDN | input | Shutdown pin; pulling SHDN low puts the device into low power shutdown mode, and cycling SHDN resets a device that has latched off due to a fault. |
| 15 | RTN | power_in | Reference for the device internal control circuits; external support components such as R(ILIM), C(dVdT), R(IMON) and the UVLO and OVP resistors are referenced to this pin. |
| 16 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 17 | GND | power_in | Connect GND to system ground. |
| 18 | IMON | output | Analog current monitor output that sources a scaled-down ratio of the current through the internal FET; a resistor from this pin to RTN converts it to a proportional voltage, and it can be left floating if unused. |
| 19 | ILIM | bidirectional | A resistor from this pin to RTN sets the overload and short-circuit current limit. |
| 20 | dVdT | bidirectional | A capacitor from this pin to RTN sets the output voltage slew rate at start-up. |
| 21 | N.C | unconnected | No connect pin, listed as N.C in the pin table. |
| 22 | FLT | output | Fault event indicator; it is an open-drain output and can be left floating if unused. |
| 23 | OUT | power_out | Power output of the device, to be connected to the load. |
| 24 | OUT | power_out | Power output of the device, to be connected to the load. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-24-EP(4x5) |
| Category | Global Sourcing Parts |
| Pins | 25 |
CAD (KiCad official)
- Symbol:
TPS26601RHFT - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: VQFN-24-EP(4x5) (KiCad packages3D, STEP)
- 3D model files:
tps26601rhft-etched.step/tps26601rhft-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps26601rhft.step/tps26601rhft.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (55 pp, sha256
fc13f366ed16ead3, retrieved 2026-10-10, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).