component
TPS24720RGTR
Public Made by Adomby adom
Texas Instruments Supervisor And Reset ICs, QFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS24720RGTR
Texas Instruments · Supervisor And Reset ICs · QFN-16-EP(3x3)
TPS24720RGTR from Texas Instruments, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Active-high enable input that enables the gate driver at 1.35 V or more, can serve as an undervoltage monitor through a resistor divider, and should not be left floating. |
| 2 | PROG | input | Power-limiting programming pin where a resistor from this pin to GND sets the maximum FET power dissipation, with a recommended resistance of 4.99 kΩ to 500 kΩ. |
| 3 | TIMER | bidirectional | A capacitor connected from this pin to GND provides the fault timing function. |
| 4 | GND | power_in | Ground reference for the device; the thermal pad is tied to GND. |
| 5 | OV | input | Overvoltage comparator input connected to a resistor divider, which pulls GATE low when OV exceeds its threshold; recommended input range is 0 V to 16 V. |
| 6 | IMON | output | Analog load-current limit program point that must be connected to ground through RIMON, with a maximum source current of 1 mA recommended. |
| 7 | SET | input | Current-limit programming pin where a resistor is connected from this pin to VCC; recommended input range is 2.5 V to 18 V. |
| 8 | OUT | input | Output voltage sensor used for monitoring MOSFET power; recommended input range is 0 V to 18 V. |
| 9 | FFLTb | output | Active-low open-drain FET fault indicator that signals a shorted MOSFET when the output is off, with a recommended sink current of 0 to 2 mA. |
| 10 | GATE | output | Gate driver output for the external MOSFET, with a 13.9 V clamp between GATE and VCC limiting gate-to-source voltage. |
| 11 | SENSE | input | Current-sensing input for the resistor shunt from VCC to SENSE; recommended input range is 2.5 V to 18 V. |
| 12 | VCC | power_in | Input-voltage sense and power supply, operating from 2.5 V to 18 V. |
| 13 | FLTb | output | Active-low open-drain output that indicates the overload fault timer has turned the MOSFET off, with a recommended sink current of 0 to 2 mA. |
| 14 | LATCH | input | Latch or retry mode select input that selects latch mode when floating or connected to a logic-level voltage and retry mode when connected to GND. |
| 15 | PGb | output | Active-low open-drain power-good indicator whose status is set by the voltage across the MOSFET, with a recommended sink current of 0 to 2 mA. |
| 16 | ENSD | input | Pull low to place the device in low-current standby mode; if not otherwise connected, it is preferably pulled up to 2 V to 18 V. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFN-16-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 17 |
CAD (KiCad official)
- Symbol:
TPS24720RGTR - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps24720rgtr-etched.step/tps24720rgtr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps24720rgtr.step/tps24720rgtr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (41 pp, sha256
af9f0c2f8f3beedd, retrieved 2026-10-07, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).