# TPS24713DGSR

**Texas Instruments** · Monitors & Reset Circuits · VSSOP-10-0.5mm

TPS24713DGSR from Texas Instruments, in a VSSOP-10-0.5mm. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

## Pinout

| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PG | output | Active-high open-drain power-good output for the TPS24713 that goes high-impedance after the FET VDS falls below 170 mV and a 3.4-ms deglitch delay elapses, and pulls low when VDS exceeds 240 mV. |
| 2 | EN | input | Active-high enable input; applying 1.35 V or more enables the gate driver, and the pin should not be left floating. |
| 3 | PROG | input | Power-limit programming pin: a resistor from this pin to GND sets the maximum MOSFET power during inrush, no voltage should be applied to it, and 4.99 kΩ is used when no constant power limit is wanted (recommended resistance 4.99 kΩ to 500 kΩ). |
| 4 | TIMER | bidirectional | A capacitor from this pin to GND provides the fault timing function, with absolute maximum input range of -0.3 V to 5 V. |
| 5 | GND | power_in | System ground connection. |
| 6 | OUT | input | Output voltage sensor that measures the drain-to-source voltage of the external MOSFET; recommended input range is 0 V to 18 V, with an absolute maximum of 30 V. |
| 7 | GATE | output | Gate driver output for the external MOSFET; a charge pump sources 30 µA and a 13.9-V clamp between GATE and VCC limits gate-to-source voltage. |
| 8 | SENSE | input | Current-sense input for the shunt resistor between VCC and SENSE; recommended input range is 2.5 V to 18 V. |
| 9 | VCC | power_in | Input-voltage sense and power supply; recommended input range is 2.5 V to 18 V. |
| 10 | FLT | output | Active-high open-drain fault output for the TPS24713 that goes high-impedance when the fault timer expires and the MOSFET is disabled in retry mode; recommended sink current is 0 to 2 mA. |

## Key specifications

| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-10-0.5mm |
| Category | Power Supply Chip |
| Pins | 10 |

## CAD (KiCad official)

- Symbol: `TPS24713DGSR`
- Footprint: `Package_SO:MSOP-10_3x3mm_P0.5mm`
- 3D model: VSSOP-10-0.5mm (KiCad packages3D, STEP)
- 3D model files: `tps24713dgsr-etched.step` / `tps24713dgsr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps24713dgsr.step` / `tps24713dgsr.glb` are the bare package body.

## Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps24713) (40 pp, sha256 `3470149f6e5539ab`, retrieved 2026-10-09, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).

[Datasheet PDF](docs/tps24713dgsr-datasheet.pdf)