component
TPS2413D
Public Made by Adomby adom
Texas Instruments Power Distribution Switches, SOIC-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+45@@ -0,0 +1,45 @@+# TPS2413D++**Texas Instruments** · Power Distribution Switches · SOIC-8++TPS2413D from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VDD | power_in | Primary supply for the gate-drive charge pump and internal controls, which must be at least 3 V (VDD must exceed 3 V to meet the gate-drive specification) and may be higher or lower than the controlled bus voltage. |+| 2 | RSET | input | A resistor from this pin to GND (1.5 kΩ to open-ended range) programs the fast turnoff threshold, where leaving it open gives a slightly positive threshold and the TPS2413 must use a negative threshold; RSET voltage is limited to -0.3 V to 7 V. |+| 3 | RSVD | power_in | Reserved pin that must be connected to GND. |+| 4 | GND | power_in | Device ground that needs a low-impedance connection to the ground plane, since it carries several amperes of rapid discharge current when the external MOSFET turns off. |+| 5 | GATE | output | Drives the gate of the external N-channel MOSFET relative to A using the BYP supply, is pulled to GND by a fast discharge on turnoff, and is rated -0.3 V to 30 V with GATE above BYP limited to 0.3 V. |+| 6 | C | input | Voltage-sense input for the simulated diode cathode, connected to the MOSFET drain, with C allowed up to 18 V above A. |+| 7 | A | input | Voltage-sense input for the simulated diode anode, connected to the MOSFET source and Kelvin connected to it, which also serves as the reference for the charge-pump supply on BYP and is limited to 7.5 V above C. |+| 8 | BYP | bidirectional | Charge-pump output and gate-drive supply that needs a capacitor from BYP to A (2200 pF ceramic recommended), and shorting BYP to a voltage below A damages the device; BYP is rated -0.3 V to 30 V with BYP to A limited to 13 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | SOIC-8 |+| Category | Power Management (PMIC) |+| Pins | 8 |++## CAD (KiCad official)++- Symbol: `TPS2413D`+- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`+- 3D model: SOIC-8 (KiCad packages3D, STEP)+- 3D model files: `tps2413d-etched.step` / `tps2413d-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps2413d.step` / `tps2413d.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps2413) (31 pp, sha256 `2d4a1bb575996a87`, retrieved 2026-10-08, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps2413d-datasheet.pdf)
page.jsonadded+200@@ -0,0 +1,200 @@+{+ "slug": "tps2413d",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Power Distribution Switches, SOIC-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "tps2413d",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps2413d.kicad_sym",+ "tps2413d.kicad_mod",+ "tps2413d.glb",+ "tps2413d.step",+ "tps2413d.lbr",+ "docs/hero.png",+ "docs/tps2413d-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps2413d-hero.glb",+ "tps2413d-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS2413D",+ "manufacturer": "Texas Instruments",+ "package": "SOIC-8",+ "pin_count": 8,+ "category": "Power Management (PMIC)",+ "subcategory": "Power Distribution Switches",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps2413",+ "parts": {+ "symbol": "tps2413d.kicad_sym",+ "footprint": "tps2413d.kicad_mod",+ "model_3d": "tps2413d-hero.glb",+ "model_3d_plain": "tps2413d.glb",+ "model_3d_step": "tps2413d-etched.step",+ "model_3d_step_plain": "tps2413d.step",+ "lbr": "tps2413d.lbr"+ },+ "distributor_links": {+ "lcsc": "C1523985",+ "digikey": "296-23786-5-ND",+ "mouser": "595-TPS2413D"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T14:36:41Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-23786-5-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS2413D",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "VDD",+ "type": "power_in",+ "description": "Primary supply for the gate-drive charge pump and internal controls, which must be at least 3 V (VDD must exceed 3 V to meet the gate-drive specification) and may be higher or lower than the controlled bus voltage."+ },+ {+ "number": "2",+ "name": "RSET",+ "type": "input",+ "description": "A resistor from this pin to GND (1.5 kΩ to open-ended range) programs the fast turnoff threshold, where leaving it open gives a slightly positive threshold and the TPS2413 must use a negative threshold; RSET voltage is limited to -0.3 V to 7 V."+ },+ {+ "number": "3",+ "name": "RSVD",+ "type": "power_in",+ "description": "Reserved pin that must be connected to GND."+ },+ {+ "number": "4",+ "name": "GND",+ "type": "power_in",+ "description": "Device ground that needs a low-impedance connection to the ground plane, since it carries several amperes of rapid discharge current when the external MOSFET turns off."+ },+ {+ "number": "5",+ "name": "GATE",+ "type": "output",+ "description": "Drives the gate of the external N-channel MOSFET relative to A using the BYP supply, is pulled to GND by a fast discharge on turnoff, and is rated -0.3 V to 30 V with GATE above BYP limited to 0.3 V."+ },+ {+ "number": "6",+ "name": "C",+ "type": "input",+ "description": "Voltage-sense input for the simulated diode cathode, connected to the MOSFET drain, with C allowed up to 18 V above A."+ },+ {+ "number": "7",+ "name": "A",+ "type": "input",+ "description": "Voltage-sense input for the simulated diode anode, connected to the MOSFET source and Kelvin connected to it, which also serves as the reference for the charge-pump supply on BYP and is limited to 7.5 V above C."+ },+ {+ "number": "8",+ "name": "BYP",+ "type": "bidirectional",+ "description": "Charge-pump output and gate-drive supply that needs a capacitor from BYP to A (2200 pF ceramic recommended), and shorting BYP to a voltage below A damages the device; BYP is rated -0.3 V to 30 V with BYP to A limited to 13 V."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The datasheet's pin diagram graphic is garbled in the text extraction, so pin numbers and names were; RSVD is typed PWR in the datasheet and mapped to power_in here; the datasheet only says it must be c; Pin A is typed as input (I) in the datasheet even though it also acts as the charge-pump reference; "+ ],+ "pages_sent": 11,+ "cost_usd": 0.0684,+ "at": "2026-10-08T14:36:24"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps2413",+ "pages": 31,+ "sha256": "2d4a1bb575996a87",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 8,+ "described": 8,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps2413d.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6,+ 4.9,+ 1.75+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "07f46cff378d30e6c27dfd5a03092c795323f86d91c71fc7e743f4f418dc553a",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps2413d-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6,+ 4.9,+ 1.75+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "5a4855a752c142c26c615d917777cf97600f86dcabcb7f020734990f65ef2290",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}