← Commit history

Initial commit: component/tps2411pwr

Ray ·f7d7f8816d ·
2 files changed +227
README.mdadded+50
@@ -0,0 +1,50 @@+# TPS2411PWR++**Texas Instruments** · Power Distribution Switches · TSSOP-14++TPS2411PWR from Texas Instruments, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VDD | power_in | Supply voltage input for gate drive charge pump and internal control circuits; must be connected to ≥3V source. |+| 2 | RSET | input | Resistor connection to ground programs the fast turn-off comparator threshold; leaving open results in slightly positive V(A-C) threshold. |+| 3 | STAT | bidirectional | Multifunction pin with weak internal pull-up to VDD; outputs high when MOSFET gate is driven high and V(GATE) exceeds V(A) plus 0.4V; pulling low shifts fast turn-off threshold negative by approximately 157mV. |+| 4 | FLTB | tri_state | Open-drain fault output, active low when VDD is insufficient, GATE should be high but is not, or forward voltage exceeds 0.4V; 3ms deglitch filter on falling edge. |+| 5 | OV | input | Overvoltage monitor input with 0.6V threshold and 7mV hysteresis; excess voltage contributes to PG output and forces MOSFET off when above threshold. |+| 6 | UV | input | Undervoltage monitor input with 0.6V threshold and 7mV hysteresis; programmable via external resistor divider and contributes to PG output. |+| 7 | GND | power_in | Device ground reference; must have low impedance connection to ground plane. |+| 8 | GATE | output | Gate drive output for external N-channel MOSFET; driven positive with respect to A by charge pump referenced to BYP, with programmable fast turn-off to ground. |+| 9 | RSVD | power_in | Reserved pin; must be connected to GND for proper device operation. |+| 10 | C | input | Voltage sense cathode input for diode emulation; connect to MOSFET drain in typical configuration; protected by internal clamp diode. |+| 11 | A | input | Voltage sense anode input for diode emulation; serves as reference for charge pump bias supply on BYP; connect to MOSFET source in typical configuration. |+| 12 | FLTR | input | Filter input for fast comparator; capacitor from FLTR to A filters spurious transients; clamped to C voltage and may be left open for fastest response. |+| 13 | BYP | bidirectional | Charge pump output and internal bias supply for comparators and gate driver; 2200pF ceramic capacitor from BYP to A required for filtering; must not be shorted below A voltage. |+| 14 | PG | tri_state | Open-drain power-good indicator output; sinks to ground if UV above threshold, OV below threshold, or internal UVLO not satisfied; multiple PG pins may be wire-ORed. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-14 |+| Category | Power Management (PMIC) |+| Pins | 14 |++## CAD (KiCad official)++- Symbol: `TPS2411PWR`+- Footprint: `Package_SO:TSSOP-14_4.4x5mm_P0.65mm`+- 3D model: TSSOP-14 (KiCad packages3D, STEP)+- 3D model files: `tps2411pwr-etched.step` / `tps2411pwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps2411pwr.step` / `tps2411pwr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps2411.pdf) (37 pp, sha256 `6edb4f17085af239`, retrieved 2026-09-23, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps2411pwr-datasheet.pdf)
page.jsonadded+177
@@ -0,0 +1,177 @@+{+  "slug": "tps2411pwr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Power Distribution Switches, TSSOP-14. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps2411pwr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps2411pwr.kicad_sym",+    "tps2411pwr.kicad_mod",+    "tps2411pwr.glb",+    "tps2411pwr.step",+    "tps2411pwr.lbr",+    "docs/hero.png",+    "docs/tps2411pwr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS2411PWR",+    "manufacturer": "Texas Instruments",+    "package": "TSSOP-14",+    "pin_count": 14,+    "category": "Power Management (PMIC)",+    "subcategory": "Power Distribution Switches",+    "datasheet": "https://www.ti.com/lit/ds/symlink/tps2411.pdf",+    "parts": {+      "symbol": "tps2411pwr.kicad_sym",+      "footprint": "tps2411pwr.kicad_mod",+      "model_3d": "tps2411pwr-etched.glb",+      "model_3d_plain": "tps2411pwr.glb",+      "model_3d_step": "tps2411pwr-etched.step",+      "model_3d_step_plain": "tps2411pwr.step",+      "lbr": "tps2411pwr.lbr"+    },+    "distributor_links": {+      "lcsc": "C2653616"+    },+    "pins": [+      {+        "number": "1",+        "name": "VDD",+        "type": "power_in",+        "description": "Supply voltage input for gate drive charge pump and internal control circuits; must be connected to ≥3V source."+      },+      {+        "number": "2",+        "name": "RSET",+        "type": "input",+        "description": "Resistor connection to ground programs the fast turn-off comparator threshold; leaving open results in slightly positive V(A-C) threshold."+      },+      {+        "number": "3",+        "name": "STAT",+        "type": "bidirectional",+        "description": "Multifunction pin with weak internal pull-up to VDD; outputs high when MOSFET gate is driven high and V(GATE) exceeds V(A) plus 0.4V; pulling low shifts fast turn-off threshold negative by approximately 157mV."+      },+      {+        "number": "4",+        "name": "FLTB",+        "type": "tri_state",+        "description": "Open-drain fault output, active low when VDD is insufficient, GATE should be high but is not, or forward voltage exceeds 0.4V; 3ms deglitch filter on falling edge."+      },+      {+        "number": "5",+        "name": "OV",+        "type": "input",+        "description": "Overvoltage monitor input with 0.6V threshold and 7mV hysteresis; excess voltage contributes to PG output and forces MOSFET off when above threshold."+      },+      {+        "number": "6",+        "name": "UV",+        "type": "input",+        "description": "Undervoltage monitor input with 0.6V threshold and 7mV hysteresis; programmable via external resistor divider and contributes to PG output."+      },+      {+        "number": "7",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground reference; must have low impedance connection to ground plane."+      },+      {+        "number": "8",+        "name": "GATE",+        "type": "output",+        "description": "Gate drive output for external N-channel MOSFET; driven positive with respect to A by charge pump referenced to BYP, with programmable fast turn-off to ground."+      },+      {+        "number": "9",+        "name": "RSVD",+        "type": "power_in",+        "description": "Reserved pin; must be connected to GND for proper device operation."+      },+      {+        "number": "10",+        "name": "C",+        "type": "input",+        "description": "Voltage sense cathode input for diode emulation; connect to MOSFET drain in typical configuration; protected by internal clamp diode."+      },+      {+        "number": "11",+        "name": "A",+        "type": "input",+        "description": "Voltage sense anode input for diode emulation; serves as reference for charge pump bias supply on BYP; connect to MOSFET source in typical configuration."+      },+      {+        "number": "12",+        "name": "FLTR",+        "type": "input",+        "description": "Filter input for fast comparator; capacitor from FLTR to A filters spurious transients; clamped to C voltage and may be left open for fastest response."+      },+      {+        "number": "13",+        "name": "BYP",+        "type": "bidirectional",+        "description": "Charge pump output and internal bias supply for comparators and gate driver; 2200pF ceramic capacitor from BYP to A required for filtering; must not be shorted below A voltage."+      },+      {+        "number": "14",+        "name": "PG",+        "type": "tri_state",+        "description": "Open-drain power-good indicator output; sinks to ground if UV above threshold, OV below threshold, or internal UVLO not satisfied; multiple PG pins may be wire-ORed."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 37,+        "cost_usd": 0.357,+        "at": "2026-09-23T09:35:09"+      },+      "datasheet": {+        "url": "https://www.ti.com/lit/ds/symlink/tps2411.pdf",+        "pages": 37,+        "sha256": "6edb4f17085af239",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 14,+        "described": 14,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file