component
TPS2411PWR
Public Made by Adomby adom
Texas Instruments Power Distribution Switches, TSSOP-14. Datasheet-verified pinout, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS2411PWR
Texas Instruments · Power Distribution Switches · TSSOP-14
TPS2411PWR from Texas Instruments, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Supply voltage input for gate drive charge pump and internal control circuits; must be connected to ≥3V source. |
| 2 | RSET | input | Resistor connection to ground programs the fast turn-off comparator threshold; leaving open results in slightly positive V(A-C) threshold. |
| 3 | STAT | bidirectional | Multifunction pin with weak internal pull-up to VDD; outputs high when MOSFET gate is driven high and V(GATE) exceeds V(A) plus 0.4V; pulling low shifts fast turn-off threshold negative by approximately 157mV. |
| 4 | FLTB | tri_state | Open-drain fault output, active low when VDD is insufficient, GATE should be high but is not, or forward voltage exceeds 0.4V; 3ms deglitch filter on falling edge. |
| 5 | OV | input | Overvoltage monitor input with 0.6V threshold and 7mV hysteresis; excess voltage contributes to PG output and forces MOSFET off when above threshold. |
| 6 | UV | input | Undervoltage monitor input with 0.6V threshold and 7mV hysteresis; programmable via external resistor divider and contributes to PG output. |
| 7 | GND | power_in | Device ground reference; must have low impedance connection to ground plane. |
| 8 | GATE | output | Gate drive output for external N-channel MOSFET; driven positive with respect to A by charge pump referenced to BYP, with programmable fast turn-off to ground. |
| 9 | RSVD | power_in | Reserved pin; must be connected to GND for proper device operation. |
| 10 | C | input | Voltage sense cathode input for diode emulation; connect to MOSFET drain in typical configuration; protected by internal clamp diode. |
| 11 | A | input | Voltage sense anode input for diode emulation; serves as reference for charge pump bias supply on BYP; connect to MOSFET source in typical configuration. |
| 12 | FLTR | input | Filter input for fast comparator; capacitor from FLTR to A filters spurious transients; clamped to C voltage and may be left open for fastest response. |
| 13 | BYP | bidirectional | Charge pump output and internal bias supply for comparators and gate driver; 2200pF ceramic capacitor from BYP to A required for filtering; must not be shorted below A voltage. |
| 14 | PG | tri_state | Open-drain power-good indicator output; sinks to ground if UV above threshold, OV below threshold, or internal UVLO not satisfied; multiple PG pins may be wire-ORed. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-14 |
| Category | Power Management (PMIC) |
| Pins | 14 |
CAD (KiCad official)
- Symbol:
TPS2411PWR - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
tps2411pwr-etched.step/tps2411pwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps2411pwr.step/tps2411pwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (37 pp, sha256
6edb4f17085af239, retrieved 2026-09-23, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).