← Commit history

Initial commit: component/tps2320ipwr

Ray ·a90789e620 ·
2 files changed +241
README.mdadded+52
@@ -0,0 +1,52 @@+# TPS2320IPWR++**Texas Instruments** · Supervisor And Reset ICs · TSSOP-16++TPS2320IPWR from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | GATE1 | output | Gate drive output for channel 1 high-side MOSFET, 10-20 µA source and 50-100 µA sink current, 9-12 V gate-to-source clamp, 30 V maximum rating. |+| 2 | GATE2 | output | Gate drive output for channel 2 high-side MOSFET, 10-20 µA source and 50-100 µA sink current, 9-12 V gate-to-source clamp, 22 V maximum rating. |+| 3 | DGND | power_in | Digital ground reference, connect to AGND as close as possible. |+| 4 | TIMER | output | Overcurrent timing node with 50 µA charge current and 2.5 mA discharge current, capacitor charging to 0.5 V threshold triggers circuit-breaker latch. |+| 5 | VREG | power_out | Regulated 3.5-5.5 V regulator output powered from IN1, requires 0.1 µF bypass capacitor to ground for stable operation. |+| 6 | AGND | power_in | Analog ground reference, connect to DGND as close as possible. |+| 7 | ISENSE2 | input | Channel 2 current-sense input connected to voltage across sense resistor between IN2 and MOSFET drain, voltage must not exceed VI(IN2). |+| 8 | ISENSE1 | input | Channel 1 current-sense input connected to voltage across sense resistor between IN1 and MOSFET drain, voltage must not exceed VI(IN1). |+| 9 | IN1 | power_in | Primary power input 3-13 V, supplies device operating current for both channels and feeds internal LDO for VREG regulator. |+| 10 | IN2 | power_in | Secondary power input 3-5.5 V for channel 2 only, independent power rail from IN1. |+| 11 | ISET2 | input | Channel 2 current-limit setting input, external resistor to IN2 sets overcurrent threshold with 50 µA internal current source pulldown. |+| 12 | ISET1 | input | Channel 1 current-limit setting input, external resistor to IN1 sets overcurrent threshold with 50 µA internal current source pulldown. |+| 13 | FAULT | output | Open-drain overcurrent fault output pulled low when overcurrent condition persists until TIMER reaches 0.5 V, latches until device reset or enable toggle. |+| 14 | ENABLE | input | Active-low TTL/CMOS compatible enable input for TPS2320, 2 V high threshold and 0.8 V low threshold, disables gates when pulled high. |+| 15 | DISCH2 | output | Channel 2 discharge transistor output connected to external MOSFET source, provides gate voltage clamping reference and 10 mA discharge current for load capacitance. |+| 16 | DISCH1 | output | Channel 1 discharge transistor output connected to external MOSFET source, provides gate voltage clamping reference and 10 mA discharge current for load capacitance. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-16 |+| Category | Power Management (PMIC) |+| Pins | 16 |++## CAD (KiCad official)++- Symbol: `TPS2320IPWR`+- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`+- 3D model: TSSOP-16 (KiCad packages3D, STEP)+- 3D model files: `tps2320ipwr-etched.step` / `tps2320ipwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps2320ipwr.step` / `tps2320ipwr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps2320) (29 pp, sha256 `0c4eed4165426632`, retrieved 2026-09-24, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps2320ipwr-datasheet.pdf)
page.jsonadded+189
@@ -0,0 +1,189 @@+{+  "slug": "tps2320ipwr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Supervisor And Reset ICs, TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps2320ipwr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps2320ipwr.kicad_sym",+    "tps2320ipwr.kicad_mod",+    "tps2320ipwr.glb",+    "tps2320ipwr.step",+    "tps2320ipwr.lbr",+    "docs/hero.png",+    "docs/tps2320ipwr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS2320IPWR",+    "manufacturer": "Texas Instruments",+    "package": "TSSOP-16",+    "pin_count": 16,+    "category": "Power Management (PMIC)",+    "subcategory": "Supervisor And Reset ICs",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps2320",+    "parts": {+      "symbol": "tps2320ipwr.kicad_sym",+      "footprint": "tps2320ipwr.kicad_mod",+      "model_3d": "tps2320ipwr-etched.glb",+      "model_3d_plain": "tps2320ipwr.glb",+      "model_3d_step": "tps2320ipwr-etched.step",+      "model_3d_step_plain": "tps2320ipwr.step",+      "lbr": "tps2320ipwr.lbr"+    },+    "distributor_links": {+      "lcsc": "C2678291"+    },+    "pins": [+      {+        "number": "1",+        "name": "GATE1",+        "type": "output",+        "description": "Gate drive output for channel 1 high-side MOSFET, 10-20 µA source and 50-100 µA sink current, 9-12 V gate-to-source clamp, 30 V maximum rating."+      },+      {+        "number": "2",+        "name": "GATE2",+        "type": "output",+        "description": "Gate drive output for channel 2 high-side MOSFET, 10-20 µA source and 50-100 µA sink current, 9-12 V gate-to-source clamp, 22 V maximum rating."+      },+      {+        "number": "3",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground reference, connect to AGND as close as possible."+      },+      {+        "number": "4",+        "name": "TIMER",+        "type": "output",+        "description": "Overcurrent timing node with 50 µA charge current and 2.5 mA discharge current, capacitor charging to 0.5 V threshold triggers circuit-breaker latch."+      },+      {+        "number": "5",+        "name": "VREG",+        "type": "power_out",+        "description": "Regulated 3.5-5.5 V regulator output powered from IN1, requires 0.1 µF bypass capacitor to ground for stable operation."+      },+      {+        "number": "6",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground reference, connect to DGND as close as possible."+      },+      {+        "number": "7",+        "name": "ISENSE2",+        "type": "input",+        "description": "Channel 2 current-sense input connected to voltage across sense resistor between IN2 and MOSFET drain, voltage must not exceed VI(IN2)."+      },+      {+        "number": "8",+        "name": "ISENSE1",+        "type": "input",+        "description": "Channel 1 current-sense input connected to voltage across sense resistor between IN1 and MOSFET drain, voltage must not exceed VI(IN1)."+      },+      {+        "number": "9",+        "name": "IN1",+        "type": "power_in",+        "description": "Primary power input 3-13 V, supplies device operating current for both channels and feeds internal LDO for VREG regulator."+      },+      {+        "number": "10",+        "name": "IN2",+        "type": "power_in",+        "description": "Secondary power input 3-5.5 V for channel 2 only, independent power rail from IN1."+      },+      {+        "number": "11",+        "name": "ISET2",+        "type": "input",+        "description": "Channel 2 current-limit setting input, external resistor to IN2 sets overcurrent threshold with 50 µA internal current source pulldown."+      },+      {+        "number": "12",+        "name": "ISET1",+        "type": "input",+        "description": "Channel 1 current-limit setting input, external resistor to IN1 sets overcurrent threshold with 50 µA internal current source pulldown."+      },+      {+        "number": "13",+        "name": "FAULT",+        "type": "output",+        "description": "Open-drain overcurrent fault output pulled low when overcurrent condition persists until TIMER reaches 0.5 V, latches until device reset or enable toggle."+      },+      {+        "number": "14",+        "name": "ENABLE",+        "type": "input",+        "description": "Active-low TTL/CMOS compatible enable input for TPS2320, 2 V high threshold and 0.8 V low threshold, disables gates when pulled high."+      },+      {+        "number": "15",+        "name": "DISCH2",+        "type": "output",+        "description": "Channel 2 discharge transistor output connected to external MOSFET source, provides gate voltage clamping reference and 10 mA discharge current for load capacitance."+      },+      {+        "number": "16",+        "name": "DISCH1",+        "type": "output",+        "description": "Channel 1 discharge transistor output connected to external MOSFET source, provides gate voltage clamping reference and 10 mA discharge current for load capacitance."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 29,+        "cost_usd": 0.3274,+        "at": "2026-09-24T08:43:11"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps2320",+        "pages": 29,+        "sha256": "0c4eed4165426632",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file