component
TPS16630RGET
Public Made by Adomby adom
Texas Instruments Surge Protection Devices (SPDs), VQFN-24(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+62@@ -0,0 +1,62 @@+# TPS16630RGET++**Texas Instruments** · Surge Protection Devices (SPDs) · VQFN-24(4x4)++TPS16630RGET from Texas Instruments, in a VQFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | IN | power_in | Power supply input connected to internal FET drain. |+| 2 | IN | power_in | Power supply input connected to internal FET drain. |+| 3 | N.C | unconnected | No connection. |+| 4 | N.C | unconnected | No connection. |+| 5 | P_IN | power_in | Device power supply voltage. Always connect P_IN directly to IN. |+| 6 | UVLO | input | Input for setting programmable UVLO threshold; undervoltage event shuts down internal FET and asserts FLT for power fault indication. |+| 7 | OVP | input | Input for setting adjustable overvoltage protection threshold (TPS16630 only); overvoltage event shuts down internal FET and asserts FLT. |+| 8 | GND | power_in | Ground connection; connect GND to system ground plane. |+| 9 | dVdT | input | Capacitor between this pin and GND sets output voltage slew rate; floating pin enables thermal regulation mode for fast output charging during power-up. |+| 10 | ILIM | input | Resistor connected to GND on this pin sets overcurrent limit threshold; typical range 3 kΩ to 30 kΩ. |+| 11 | MODE | input | Mode selection pin for overload fault response; open for latch mode, shorted to GND for auto-retry mode. |+| 12 | SHDN | input | Shutdown pin; pulling below 0.8 V puts device into low-power shutdown mode (21 µA typ); voltage above 2 V enables device. |+| 13 | IMON | output | Analog current monitor output proportional to internal FET current; resistor to GND converts current to voltage (27.9 µA/A typ gain). |+| 14 | FLT | output | Fault event indicator with open-drain output; asserts low on UVLO, OVP, overcurrent, or thermal shutdown events. |+| 15 | N.C | unconnected | No connection. |+| 16 | PGOOD | output | Power good indicator with open-drain output, active high; goes low during fault or when SHDN is pulled low. |+| 17 | OUT | power_out | Device power output; source for protected load current. |+| 18 | OUT | power_out | Device power output; source for protected load current. |+| 19 | N.C | unconnected | No connection. |+| 20 | N.C | unconnected | No connection. |+| 21 | N.C | unconnected | No connection. |+| 22 | N.C | unconnected | No connection. |+| 23 | N.C | unconnected | No connection. |+| 24 | N.C | unconnected | No connection; PowerPAD thermal pad connects to GND plane for heat dissipation. |+| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-24(4x4) |+| Category | Circuit Protection |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `TPS16630RGET`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`+- 3D model: VQFN-24(4x4) (KiCad packages3D, STEP)+- 3D model files: `tps16630rget-etched.step` / `tps16630rget-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps16630rget.step` / `tps16630rget.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps1663) (46 pp, sha256 `ef1077e8989a204c`, retrieved 2026-10-01, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps16630rget-datasheet.pdf)
page.jsonadded+259@@ -0,0 +1,259 @@+{+ "slug": "tps16630rget",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Surge Protection Devices (SPDs), VQFN-24(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "circuit protection",+ "tps16630rget",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps16630rget.kicad_sym",+ "tps16630rget.kicad_mod",+ "tps16630rget.glb",+ "tps16630rget.step",+ "tps16630rget.lbr",+ "docs/hero.png",+ "docs/tps16630rget-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "component": {+ "mpn": "TPS16630RGET",+ "manufacturer": "Texas Instruments",+ "package": "VQFN-24(4x4)",+ "pin_count": 25,+ "category": "Circuit Protection",+ "subcategory": "Surge Protection Devices (SPDs)",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps1663",+ "parts": {+ "symbol": "tps16630rget.kicad_sym",+ "footprint": "tps16630rget.kicad_mod",+ "model_3d": "tps16630rget-etched.glb",+ "model_3d_plain": "tps16630rget.glb",+ "model_3d_step": "tps16630rget-etched.step",+ "model_3d_step_plain": "tps16630rget.step",+ "lbr": "tps16630rget.lbr"+ },+ "distributor_links": {+ "lcsc": "C2155684",+ "digikey": "296-TPS16630RGETTR-ND",+ "mouser": "595-TPS16630RGET"+ },+ "distributor_check": {+ "checked_at": "2026-10-01T03:16:25Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-TPS16630RGETTR-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "595-TPS16630RGET",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "IN",+ "type": "power_in",+ "description": "Power supply input connected to internal FET drain."+ },+ {+ "number": "2",+ "name": "IN",+ "type": "power_in",+ "description": "Power supply input connected to internal FET drain."+ },+ {+ "number": "3",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection."+ },+ {+ "number": "4",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection."+ },+ {+ "number": "5",+ "name": "P_IN",+ "type": "power_in",+ "description": "Device power supply voltage. Always connect P_IN directly to IN."+ },+ {+ "number": "6",+ "name": "UVLO",+ "type": "input",+ "description": "Input for setting programmable UVLO threshold; undervoltage event shuts down internal FET and asserts FLT for power fault indication."+ },+ {+ "number": "7",+ "name": "OVP",+ "type": "input",+ "description": "Input for setting adjustable overvoltage protection threshold (TPS16630 only); overvoltage event shuts down internal FET and asserts FLT."+ },+ {+ "number": "8",+ "name": "GND",+ "type": "power_in",+ "description": "Ground connection; connect GND to system ground plane."+ },+ {+ "number": "9",+ "name": "dVdT",+ "type": "input",+ "description": "Capacitor between this pin and GND sets output voltage slew rate; floating pin enables thermal regulation mode for fast output charging during power-up."+ },+ {+ "number": "10",+ "name": "ILIM",+ "type": "input",+ "description": "Resistor connected to GND on this pin sets overcurrent limit threshold; typical range 3 kΩ to 30 kΩ."+ },+ {+ "number": "11",+ "name": "MODE",+ "type": "input",+ "description": "Mode selection pin for overload fault response; open for latch mode, shorted to GND for auto-retry mode."+ },+ {+ "number": "12",+ "name": "SHDN",+ "type": "input",+ "description": "Shutdown pin; pulling below 0.8 V puts device into low-power shutdown mode (21 µA typ); voltage above 2 V enables device."+ },+ {+ "number": "13",+ "name": "IMON",+ "type": "output",+ "description": "Analog current monitor output proportional to internal FET current; resistor to GND converts current to voltage (27.9 µA/A typ gain)."+ },+ {+ "number": "14",+ "name": "FLT",+ "type": "output",+ "description": "Fault event indicator with open-drain output; asserts low on UVLO, OVP, overcurrent, or thermal shutdown events."+ },+ {+ "number": "15",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection."+ },+ {+ "number": "16",+ "name": "PGOOD",+ "type": "output",+ "description": "Power good indicator with open-drain output, active high; goes low during fault or when SHDN is pulled low."+ },+ {+ "number": "17",+ "name": "OUT",+ "type": "power_out",+ "description": "Device power output; source for protected load current."+ },+ {+ "number": "18",+ "name": "OUT",+ "type": "power_out",+ "description": "Device power output; source for protected load current."+ },+ {+ "number": "19",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection."+ },+ {+ "number": "20",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection."+ },+ {+ "number": "21",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection."+ },+ {+ "number": "22",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection."+ },+ {+ "number": "23",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection."+ },+ {+ "number": "24",+ "name": "N.C",+ "type": "unconnected",+ "description": "No connection; PowerPAD thermal pad connects to GND plane for heat dissipation."+ },+ {+ "number": "25",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "exposed pad 25 added from the footprint"+ ],+ "pages_sent": 31,+ "cost_usd": 0.239,+ "at": "2026-10-01T03:16:08"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps1663",+ "pages": 46,+ "sha256": "ef1077e8989a204c",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 25,+ "described": 25,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}