main
Ray
Publish 0.1.0
90cdc40
TPD3S716QDBQRQ1
Texas Instruments · Surge Suppressors · SSOP-16-150mil
TPD3S716QDBQRQ1 from Texas Instruments, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect; leave floating or connect to ground, and do not connect to VBUS_CON. |
| 2 | VBUS_CON | output | Connect to USB connector VBUS; provides IEC 61000-4-2 ESD protection, and the pin withstands −0.3 V to 18 V per the absolute maximum ratings. |
| 3 | VBUS_CON | output | Connect to USB connector VBUS; provides IEC 61000-4-2 ESD protection, and the pin withstands −0.3 V to 18 V per the absolute maximum ratings. |
| 4 | GND | power_in | Ground; connect to PCB ground plane. |
| 5 | VD- | bidirectional | Connect to USB connector D-; provides IEC 61000-4-2 ESD protection and is rated −0.3 V to 18 V per the absolute maximum ratings. |
| 6 | VD+ | bidirectional | Connect to USB connector D+; provides IEC 61000-4-2 ESD protection and is rated −0.3 V to 18 V per the absolute maximum ratings. |
| 7 | VEN | input | Active-low enable input; drive low to enable the VBUS path and high to disable it, with a recommended voltage range of 0 V to 5.9 V. |
| 8 | DEN | input | Active-low enable input; drive low to enable the data path and high to disable it, with a recommended voltage range of 0 V to 5.9 V. |
| 9 | VIN | power_in | Connect to 3.3-V I/O; controls the OVP threshold for VD+/VD-, with a recommended supply range of 3 V to 3.6 V. |
| 10 | FLT | output | Open-drain fault output that is pulled low when a fault occurs; absolute maximum −0.3 V to 7 V and VOL of 0.4 V max at 3 mA. |
| 11 | D+ | bidirectional | Connect to the internal transceiver D+ pin. |
| 12 | D- | bidirectional | Connect to the internal transceiver D- pin. |
| 13 | GND | power_in | Ground; connect to PCB ground plane. |
| 14 | VBUS_SYS | input | Connect to internal VBUS plane; recommended internal supply DC voltage is 4.75 V to 5.9 V. |
| 15 | VBUS_SYS | input | Connect to internal VBUS plane; recommended internal supply DC voltage is 4.75 V to 5.9 V. |
| 16 | IADJ | input | Connect to a resistor to GND to set the current limit threshold; RADJ is specified at a minimum of 57 kΩ. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SSOP-16-150mil |
| Category | TVS/Fuse/Board Level Protection |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VBUS_CON Supply voltage from USB connector | -0.3 | 18 | V | 4 | |||
| VBUS_SYS Internal Supply DC voltage Rail on the PCB | -0.3 | 6 | V | 4 | |||
| VD+, VD- Voltage range from connector-side USB data lines | -0.3 | 18 | V | 4 | |||
| D+, D- Voltage range for internal USB data lines | -0.3 | V | max printed as VIN + 0.3 V | 4 | |||
| VIN Voltage range for VIN supply input | -0.3 | 4 | V | 4 | |||
| Voltage on enable pin DEN | DEN | 7 | V | 4 | |||
| Voltage on enable pin VEN | VEN | 7 | V | 4 | |||
| IBUS Maximum DC output current on VBUS_CON pin | IBUS | 2.4 | A | 4 | |||
| Voltage range for IADJ pin | VIADJ | -0.3 | V | max printed as VVBUS_SYS + 0.3 V | 4 | ||
| Voltage range for the FLT pin | VFLT | -0.3 | 7 | V | 4 | ||
| TA Operating free air temperature | TA | -40 | 125 | °C | 4 | ||
| TSTG Storage temperature | TSTG | -65 | 150 | °C | 4 | ||
| VBUS_CON Supply voltage from USB connector (recommended) | 5.9 | V | 4 | ||||
| VBUS_SYS Internal supply DC voltage Rail on the PCB (recommended) | 4.75 | 5.9 | V | 4 | |||
| VD+, VD- Voltage range from connector-side USB data lines (recommended) | 0 | V | max printed as VIN + 0.3 V | 4 | |||
| D+, D- Voltage range for internal USB data lines (recommended) | 0 | V | max printed as VIN + 0.3 V | 5 | |||
| VIN Voltage range for VIN supply | VIN | 3 | 3.6 | V | 5 | ||
| IBUS Current through VBUS switch | IBUS | 2.4 | A | 5 | |||
| VEN, DEN Voltage range for enable | VEN, DEN | 0 | 5.9 | V | 5 | ||
| CSYS Input capacitance VBUS_SYS pin | CSYS | 100 | µF | 5 | |||
| CLOAD Output load capacitance VBUS_CON pin | CLOAD | 1 | µF | 5 | |||
| CVIN VIN capacitance VIN pin | CVIN | 1 | µF | 5 | |||
| RADJ Resistance of RADJ resistor IADJ pin | RADJ | 57 | kΩ | 5 | |||
| VBUS sleep current consumption | IVBUS_SLEEP | 45 | 150 | µA | Measured at VBUS_SYS pin, VEN = 5 V, DEN = 5 V | 5 | |
| VBUS operating current consumption | IVBUS | 285 | 380 | µA | Measured at VBUS_SYS pin | 5 | |
| Leakage current for VIN | IVIN | 12 | 20 | µA | Measured at VIN pin, VIN = 3.6 V | 5 | |
| Leakage into VBUS_SYS while shorted to battery and powered on | ION(LEAK) | 225 | 300 | µA | Measured flowing into VBUS_SYS pin, VBUS_SYS = 5 V, VBUS_CON = 18 V | 5 | |
| Leakage out of data path while shorted to battery and unpowered | ID(OFF_LEAK) | -1 | 1 | µA | Measured flowing out of D+ or D- pins, VBUS_SYS = 0 V, VD+ or VD- = 18 V, VIN = 0 V, D+/D- = 0 V | 5 | |
| Leakage out of data path while shorted to battery and powered on | ID(ON_LEAK) | -1 | 1 | µA | Measured flowing out of D+ or D- pins, VBUS_SYS = 5 V, VD+ or VD- = 18 V, VIN = 3.3 V, D+/D- = 0 V | 5 | |
| Undervoltage lockout rising for VIN | VUVLO(RISING) | 2.6 | 2.7 | 2.9 | V | Ramp VIN up until VBUS and Data FETs turn on, VEN = 0 V, DEN = 0 V | 6 |
| Undervoltage lockout falling for VIN | VUVLO(FALLING) | 2.5 | 2.6 | 2.8 | V | Ramp VIN down until VBUS and Data FETs turn off, VEN = 0 V, DEN = 0 V | 6 |
| Overcurrent limit VBUS | ILIM | 505 | 620 | mA | RADJ = 280 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 | |
| Overcurrent limit VBUS | ILIM | 0.905 | 1.1 | A | RADJ = 158 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 | |
| Overcurrent limit VBUS | ILIM | 1.005 | 1.2 | A | RADJ = 143 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 | |
| Overcurrent limit VBUS | ILIM | 1.505 | 1.8 | A | RADJ = 93.1 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 | |
| Overcurrent limit VBUS | ILIM | 1.8 | 2.16 | A | RADJ = 76.8 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 | |
| Overcurrent limit VBUS | ILIM | 2.105 | 2.57 | A | RADJ = 66.5 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 | |
| Overcurrent limit VBUS | ILIM | 2.405 | 2.93 | A | RADJ = 57.6 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 | |
| Overcurrent limit VBUS | ILIM | 550 | 700 | 850 | mA | IADJ = GND; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 1.1 | 1.4 | 1.7 | A | IADJ = VBUS_SYS; progressively load VBUS_CON until device asserts FLT | 6 |
| The rising over-temperature protection shutdown threshold | TSD(RISING) | 150 | 165 | 180 | ℃ | VBUS_SYS = 5 V, VEN = 0 V, DEN = 0 V, no load on VBUS_CON; TA stepped up until FLT asserted | 6 |
| The falling over-temperature protection shutdown threshold | TSD(FALLING) | 125 | 130 | 142 | ℃ | VBUS_SYS = 5 V, VEN = 0 V, DEN = 0 V, no load on VBUS_CON; TA stepped down until FLT deasserted | 6 |
| The over-temperature protection shutdown threshold hysteresis | TSD(HYST) | 10 | 35 | 55 | ℃ | TSD(RISING), TSD(FALLING) | 6 |
| Input overvoltage protection threshold VBUS_CON rising | VOVP(RISING) | 5.6 | 5.8 | 6 | V | Increase VBUS_CON from 5 V to 7 V; measure when FLT is asserted | 6 |
| Input overvoltage protection threshold VBUS_CON falling | VOVP(FALLING) | 5.52 | 5.75 | 5.98 | V | Decrease VBUS_CON from 7 V to 5 V; measure when FLT is deasserted | 6 |
| Reverse supply detection threshold rising VBUS_CON, VBUS_SYS | VREV_SUPPLY(RISING) | 140 | 200 | 260 | mV | VBUS_SYS = 5 V; increase VBUS_CON from VBUS_SYS to VBUS_SYS + 300 mV; 25°C ≤ TA ≤ 125°C | 6 |
| Reverse supply detection threshold falling VBUS_CON, VBUS_SYS | VREV_SUPPLY(FALLING) | 70 | 120 | 165 | mV | VBUS_SYS = 5 V; decrease VBUS_CON from VBUS_SYS + 300 mV to VBUS_SYS; 25°C ≤ TA ≤ 125°C | 6 |
| Undervoltage lockout rising for VBUS_SYS | VUVLO(SYS_RISING) | 3.1 | 3.3 | 3.6 | V | VBUS_SYS voltage rising from 0 V to 5 V | 7 |
| VBUS_SYS UVLO Hysteresis | VHYS(UVLO_SYS) | 50 | 75 | 100 | mV | Difference between rising and falling UVLO thresholds on VBUS_SYS | 7 |
| Undervoltage lockout falling for VBUS_SYS | VUVLO(SYS_FALLING) | 3 | 3.2 | 3.5 | V | VBUS_SYS voltage falling from 5 V to 2.9 V | 7 |
| Short-to-ground comparator rising threshold VBUS_CON | VSHRT(RISING) | 2.5 | 2.6 | 2.7 | V | Increase VBUS_CON from 0 V until device transitions from short-circuit to over-current mode | 7 |
| Short-to-ground comparator falling threshold VBUS_CON | VSHRT(FALLING) | 2.4 | 2.5 | 2.6 | V | VBUS_SYS = 5 V; VIN = 3.3 V; VEN = 0 V, DEN = 0 V; decrease VBUS_CON from 5 V until transition to short-circuit mode | 7 |
| Short-to-ground current source VBUS_CON | ISHRT | 150 | 350 | mA | Current sourced from VBUS_SYS when device is in short-circuit mode | 7 | |
| On Resistance between D+ and VD+ or D- and VD- | RON | 4 | 6.5 | Ω | Measure between D+ and VD+ or D- and VD-, voltage between 0 V and 0.4 V | 7 | |
| On Resistance flatness | RON(Flat) | 0.2 | 1 | Ω | Measure between D+ and VD+ or D- and VD-, sweep voltage between 0 V and 0.4 V | 7 | |
| Output discharge resistance | R(DISCHARGE) | 18 | 30 | kΩ | VEN = 5 V, DEN = 5 V, VBUS_CON = 5 V; measure current flow to ground | 7 | |
| VBUS path ON resistance | RON | 63 | 135 | mΩ | VBUS_CON = 5 V, IOUT = 1.5 A | 7 | |
| OVP Response time VBUS | tOVP_response | 2 | 4 | µs | Measured from OVP condition to FET turnoff | 8 | |
| Junction-to-ambient thermal resistance | θJA | 98.8 | °C/W | 5 | |||
| Junction-to-ambient thermal resistance (custom layout) | θJA(Custom) | 57 | °C/W | See Layout Optimized for Thermal Performance section | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | signal pins when possible. Another key strategy is to maximize the copper weight of the PCB metal layers. This | 24 |
CAD (KiCad official)
- Symbol:
TPD3S716QDBQRQ1 - Footprint:
Package_SO:SSOP-16_3.9x4.9mm_P0.635mm - 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (33 pp, sha256
3c73efd1fb7bad2b, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPD3S716QDBQRQ1
**Texas Instruments** · Surge Suppressors · SSOP-16-150mil
TPD3S716QDBQRQ1 from Texas Instruments, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect; leave floating or connect to ground, and do not connect to VBUS_CON. |
| 2 | VBUS_CON | output | Connect to USB connector VBUS; provides IEC 61000-4-2 ESD protection, and the pin withstands −0.3 V to 18 V per the absolute maximum ratings. |
| 3 | VBUS_CON | output | Connect to USB connector VBUS; provides IEC 61000-4-2 ESD protection, and the pin withstands −0.3 V to 18 V per the absolute maximum ratings. |
| 4 | GND | power_in | Ground; connect to PCB ground plane. |
| 5 | VD- | bidirectional | Connect to USB connector D-; provides IEC 61000-4-2 ESD protection and is rated −0.3 V to 18 V per the absolute maximum ratings. |
| 6 | VD+ | bidirectional | Connect to USB connector D+; provides IEC 61000-4-2 ESD protection and is rated −0.3 V to 18 V per the absolute maximum ratings. |
| 7 | VEN | input | Active-low enable input; drive low to enable the VBUS path and high to disable it, with a recommended voltage range of 0 V to 5.9 V. |
| 8 | DEN | input | Active-low enable input; drive low to enable the data path and high to disable it, with a recommended voltage range of 0 V to 5.9 V. |
| 9 | VIN | power_in | Connect to 3.3-V I/O; controls the OVP threshold for VD+/VD-, with a recommended supply range of 3 V to 3.6 V. |
| 10 | FLT | output | Open-drain fault output that is pulled low when a fault occurs; absolute maximum −0.3 V to 7 V and VOL of 0.4 V max at 3 mA. |
| 11 | D+ | bidirectional | Connect to the internal transceiver D+ pin. |
| 12 | D- | bidirectional | Connect to the internal transceiver D- pin. |
| 13 | GND | power_in | Ground; connect to PCB ground plane. |
| 14 | VBUS_SYS | input | Connect to internal VBUS plane; recommended internal supply DC voltage is 4.75 V to 5.9 V. |
| 15 | VBUS_SYS | input | Connect to internal VBUS plane; recommended internal supply DC voltage is 4.75 V to 5.9 V. |
| 16 | IADJ | input | Connect to a resistor to GND to set the current limit threshold; RADJ is specified at a minimum of 57 kΩ. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SSOP-16-150mil |
| Category | TVS/Fuse/Board Level Protection |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VBUS_CON Supply voltage from USB connector | | -0.3 | | 18 | V | | 4 |
| VBUS_SYS Internal Supply DC voltage Rail on the PCB | | -0.3 | | 6 | V | | 4 |
| VD+, VD- Voltage range from connector-side USB data lines | | -0.3 | | 18 | V | | 4 |
| D+, D- Voltage range for internal USB data lines | | -0.3 | | | V | max printed as VIN + 0.3 V | 4 |
| VIN Voltage range for VIN supply input | | -0.3 | | 4 | V | | 4 |
| Voltage on enable pin DEN | DEN | | | 7 | V | | 4 |
| Voltage on enable pin VEN | VEN | | | 7 | V | | 4 |
| IBUS Maximum DC output current on VBUS_CON pin | IBUS | | | 2.4 | A | | 4 |
| Voltage range for IADJ pin | VIADJ | -0.3 | | | V | max printed as VVBUS_SYS + 0.3 V | 4 |
| Voltage range for the FLT pin | VFLT | -0.3 | | 7 | V | | 4 |
| TA Operating free air temperature | TA | -40 | | 125 | °C | | 4 |
| TSTG Storage temperature | TSTG | -65 | | 150 | °C | | 4 |
| VBUS_CON Supply voltage from USB connector (recommended) | | | | 5.9 | V | | 4 |
| VBUS_SYS Internal supply DC voltage Rail on the PCB (recommended) | | 4.75 | | 5.9 | V | | 4 |
| VD+, VD- Voltage range from connector-side USB data lines (recommended) | | 0 | | | V | max printed as VIN + 0.3 V | 4 |
| D+, D- Voltage range for internal USB data lines (recommended) | | 0 | | | V | max printed as VIN + 0.3 V | 5 |
| VIN Voltage range for VIN supply | VIN | 3 | | 3.6 | V | | 5 |
| IBUS Current through VBUS switch | IBUS | | | 2.4 | A | | 5 |
| VEN, DEN Voltage range for enable | VEN, DEN | 0 | | 5.9 | V | | 5 |
| CSYS Input capacitance VBUS_SYS pin | CSYS | 100 | | | µF | | 5 |
| CLOAD Output load capacitance VBUS_CON pin | CLOAD | 1 | | | µF | | 5 |
| CVIN VIN capacitance VIN pin | CVIN | 1 | | | µF | | 5 |
| RADJ Resistance of RADJ resistor IADJ pin | RADJ | 57 | | | kΩ | | 5 |
| VBUS sleep current consumption | IVBUS_SLEEP | | 45 | 150 | µA | Measured at VBUS_SYS pin, VEN = 5 V, DEN = 5 V | 5 |
| VBUS operating current consumption | IVBUS | | 285 | 380 | µA | Measured at VBUS_SYS pin | 5 |
| Leakage current for VIN | IVIN | | 12 | 20 | µA | Measured at VIN pin, VIN = 3.6 V | 5 |
| Leakage into VBUS_SYS while shorted to battery and powered on | ION(LEAK) | | 225 | 300 | µA | Measured flowing into VBUS_SYS pin, VBUS_SYS = 5 V, VBUS_CON = 18 V | 5 |
| Leakage out of data path while shorted to battery and unpowered | ID(OFF_LEAK) | -1 | | 1 | µA | Measured flowing out of D+ or D- pins, VBUS_SYS = 0 V, VD+ or VD- = 18 V, VIN = 0 V, D+/D- = 0 V | 5 |
| Leakage out of data path while shorted to battery and powered on | ID(ON_LEAK) | -1 | | 1 | µA | Measured flowing out of D+ or D- pins, VBUS_SYS = 5 V, VD+ or VD- = 18 V, VIN = 3.3 V, D+/D- = 0 V | 5 |
| Undervoltage lockout rising for VIN | VUVLO(RISING) | 2.6 | 2.7 | 2.9 | V | Ramp VIN up until VBUS and Data FETs turn on, VEN = 0 V, DEN = 0 V | 6 |
| Undervoltage lockout falling for VIN | VUVLO(FALLING) | 2.5 | 2.6 | 2.8 | V | Ramp VIN down until VBUS and Data FETs turn off, VEN = 0 V, DEN = 0 V | 6 |
| Overcurrent limit VBUS | ILIM | 505 | | 620 | mA | RADJ = 280 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 0.905 | | 1.1 | A | RADJ = 158 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 1.005 | | 1.2 | A | RADJ = 143 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 1.505 | | 1.8 | A | RADJ = 93.1 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 1.8 | | 2.16 | A | RADJ = 76.8 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 2.105 | | 2.57 | A | RADJ = 66.5 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 2.405 | | 2.93 | A | RADJ = 57.6 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 550 | 700 | 850 | mA | IADJ = GND; progressively load VBUS_CON until device asserts FLT | 6 |
| Overcurrent limit VBUS | ILIM | 1.1 | 1.4 | 1.7 | A | IADJ = VBUS_SYS; progressively load VBUS_CON until device asserts FLT | 6 |
| The rising over-temperature protection shutdown threshold | TSD(RISING) | 150 | 165 | 180 | ℃ | VBUS_SYS = 5 V, VEN = 0 V, DEN = 0 V, no load on VBUS_CON; TA stepped up until FLT asserted | 6 |
| The falling over-temperature protection shutdown threshold | TSD(FALLING) | 125 | 130 | 142 | ℃ | VBUS_SYS = 5 V, VEN = 0 V, DEN = 0 V, no load on VBUS_CON; TA stepped down until FLT deasserted | 6 |
| The over-temperature protection shutdown threshold hysteresis | TSD(HYST) | 10 | 35 | 55 | ℃ | TSD(RISING), TSD(FALLING) | 6 |
| Input overvoltage protection threshold VBUS_CON rising | VOVP(RISING) | 5.6 | 5.8 | 6 | V | Increase VBUS_CON from 5 V to 7 V; measure when FLT is asserted | 6 |
| Input overvoltage protection threshold VBUS_CON falling | VOVP(FALLING) | 5.52 | 5.75 | 5.98 | V | Decrease VBUS_CON from 7 V to 5 V; measure when FLT is deasserted | 6 |
| Reverse supply detection threshold rising VBUS_CON, VBUS_SYS | VREV_SUPPLY(RISING) | 140 | 200 | 260 | mV | VBUS_SYS = 5 V; increase VBUS_CON from VBUS_SYS to VBUS_SYS + 300 mV; 25°C ≤ TA ≤ 125°C | 6 |
| Reverse supply detection threshold falling VBUS_CON, VBUS_SYS | VREV_SUPPLY(FALLING) | 70 | 120 | 165 | mV | VBUS_SYS = 5 V; decrease VBUS_CON from VBUS_SYS + 300 mV to VBUS_SYS; 25°C ≤ TA ≤ 125°C | 6 |
| Undervoltage lockout rising for VBUS_SYS | VUVLO(SYS_RISING) | 3.1 | 3.3 | 3.6 | V | VBUS_SYS voltage rising from 0 V to 5 V | 7 |
| VBUS_SYS UVLO Hysteresis | VHYS(UVLO_SYS) | 50 | 75 | 100 | mV | Difference between rising and falling UVLO thresholds on VBUS_SYS | 7 |
| Undervoltage lockout falling for VBUS_SYS | VUVLO(SYS_FALLING) | 3 | 3.2 | 3.5 | V | VBUS_SYS voltage falling from 5 V to 2.9 V | 7 |
| Short-to-ground comparator rising threshold VBUS_CON | VSHRT(RISING) | 2.5 | 2.6 | 2.7 | V | Increase VBUS_CON from 0 V until device transitions from short-circuit to over-current mode | 7 |
| Short-to-ground comparator falling threshold VBUS_CON | VSHRT(FALLING) | 2.4 | 2.5 | 2.6 | V | VBUS_SYS = 5 V; VIN = 3.3 V; VEN = 0 V, DEN = 0 V; decrease VBUS_CON from 5 V until transition to short-circuit mode | 7 |
| Short-to-ground current source VBUS_CON | ISHRT | 150 | | 350 | mA | Current sourced from VBUS_SYS when device is in short-circuit mode | 7 |
| On Resistance between D+ and VD+ or D- and VD- | RON | | 4 | 6.5 | Ω | Measure between D+ and VD+ or D- and VD-, voltage between 0 V and 0.4 V | 7 |
| On Resistance flatness | RON(Flat) | | 0.2 | 1 | Ω | Measure between D+ and VD+ or D- and VD-, sweep voltage between 0 V and 0.4 V | 7 |
| Output discharge resistance | R(DISCHARGE) | 18 | | 30 | kΩ | VEN = 5 V, DEN = 5 V, VBUS_CON = 5 V; measure current flow to ground | 7 |
| VBUS path ON resistance | RON | | 63 | 135 | mΩ | VBUS_CON = 5 V, IOUT = 1.5 A | 7 |
| OVP Response time VBUS | tOVP_response | | 2 | 4 | µs | Measured from OVP condition to FET turnoff | 8 |
| Junction-to-ambient thermal resistance | θJA | | 98.8 | | °C/W | | 5 |
| Junction-to-ambient thermal resistance (custom layout) | θJA(Custom) | | 57 | | °C/W | See Layout Optimized for Thermal Performance section | 5 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | signal pins when possible. Another key strategy is to maximize the copper weight of the PCB metal layers. This | 24 |
## CAD (KiCad official)
- Symbol: `TPD3S716QDBQRQ1`
- Footprint: `Package_SO:SSOP-16_3.9x4.9mm_P0.635mm`
- 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tpd3s716-q1.pdf) (33 pp, sha256 `3c73efd1fb7bad2b`, retrieved 2026-11-11, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tpd3s716qdbqrq1-datasheet.pdf)