component
TMS320F28032PNTR
Public Made by Adomby adom
Texas Instruments Microcontrollers (MCU/MPU/SOC), LQFP-80(12x12). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTMS320F28032PNTR
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-80(12x12)
TMS320F28032PNTR from Texas Instruments, in a LQFP-80(12x12). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO22/EQEP1S/LINTXA | bidirectional | General-purpose I/O 22 with internal pull-up option; alternate functions eQEP1 strobe and LIN transmit A. |
| 2 | GPIO32/SDAA/EPWMSYNCI/ADCSOCAO | bidirectional | General-purpose I/O 32; alternate functions I2C data (open-drain), ePWM sync input and ADC start-of-conversion A output. |
| 3 | GPIO33/SCLA/EPWMSYNCO/ADCSOCBO | bidirectional | General-purpose I/O 33; alternate functions I2C clock (open-drain), ePWM sync output and ADC start-of-conversion B output. |
| 4 | GPIO23/EQEP1I/LINRXA | bidirectional | General-purpose I/O 23; alternate functions eQEP1 index and LIN receive A. |
| 5 | GPIO42/COMP1OUT | bidirectional | General-purpose I/O 42; alternate function is comparator 1 direct output. |
| 6 | GPIO43/COMP2OUT | bidirectional | General-purpose I/O 43; alternate function is comparator 2 direct output. |
| 7 | VDD | power_in | CPU and logic digital power pin; with internal VREG place a 1.2 uF (minimum) capacitor to ground on each VDD pin. |
| 8 | VSS | power_in | Digital ground pin. |
| 9 | XRS | bidirectional | Device reset input and watchdog reset output (open-drain with internal pull-up); use 2.2k-10k resistor to VDDIO and no more than 100 nF capacitor to VSS. |
| 10 | TRST | input | JTAG test reset with internal pull-down; high enables scan system, must be held low in normal operation; external pull-down required (typically 2.2k). |
| 11 | ADCINA7 | input | ADC group A channel 7 input. |
| 12 | ADCINA6/COMP3A/AIO6 | bidirectional | ADC group A channel 6 input, comparator 3A input, or digital AIO 6. |
| 13 | ADCINA5 | input | ADC group A channel 5 input. |
| 14 | ADCINA4/COMP2A/AIO4 | bidirectional | ADC group A channel 4 input, comparator 2A input, or digital AIO 4. |
| 15 | ADCINA3 | input | ADC group A channel 3 input. |
| 16 | ADCINA2/COMP1A/AIO2 | bidirectional | ADC group A channel 2 input, comparator 1A input, or digital AIO 2. |
| 17 | ADCINA1 | input | ADC group A channel 1 input. |
| 18 | ADCINA0 | input | ADC group A channel 0 input. |
| 19 | VREFHI | input | ADC external reference high, used only in ADC external reference mode; must not exceed VDDA. |
| 20 | VDDA | power_in | Analog power pin; connect a 2.2 uF (typical) capacitor near this pin. |
| 21 | VSSA | power_in | Analog ground pin. |
| 22 | VREFLO | input | ADC external reference low. |
| 23 | ADCINB0 | input | ADC group B channel 0 input. |
| 24 | ADCINB1 | input | ADC group B channel 1 input. |
| 25 | ADCINB2/COMP1B/AIO10 | bidirectional | ADC group B channel 2 input, comparator 1B input, or digital AIO 10. |
| 26 | ADCINB3 | input | ADC group B channel 3 input. |
| 27 | ADCINB4/COMP2B/AIO12 | bidirectional | ADC group B channel 4 input, comparator 2B input, or digital AIO 12. |
| 28 | ADCINB5 | input | ADC group B channel 5 input. |
| 29 | ADCINB6/COMP3B/AIO14 | bidirectional | ADC group B channel 6 input, comparator 3B input, or digital AIO 14. |
| 30 | ADCINB7 | input | ADC group B channel 7 input. |
| 31 | GPIO27/HRCAP2/SPISTEB | bidirectional | General-purpose I/O 27; alternate functions HRCAP2 input and SPI-B slave transmit enable. |
| 32 | GPIO31/CANTXA | bidirectional | General-purpose I/O 31; alternate function CAN transmit. |
| 33 | GPIO30/CANRXA | bidirectional | General-purpose I/O 30; alternate function CAN receive. |
| 34 | GPIO29/SCITXDA/SCLA/TZ3 | bidirectional | General-purpose I/O 29; alternate functions SCI transmit, I2C clock (open-drain) and trip-zone input 3. |
| 35 | VSS | power_in | Digital ground pin. |
| 36 | VDDIO | power_in | Digital I/O buffer and flash power pin; single supply when VREG is enabled, place a decoupling capacitor on each pin. |
| 37 | GPIO26/HRCAP1/SPICLKB | bidirectional | General-purpose I/O 26; alternate functions HRCAP1 input and SPI-B clock. |
| 38 | TEST2 | unconnected | Test pin reserved for TI; must be left unconnected. |
| 39 | GPIO9/EPWM5B/LINTXA/HRCAP1 | bidirectional | General-purpose I/O 9; alternate functions ePWM5B output, LIN transmit A and HRCAP1 input. |
| 40 | GPIO28/SCIRXDA/SDAA/TZ2 | bidirectional | General-purpose I/O 28; alternate functions SCI receive, I2C data (open-drain) and trip-zone input 2. |
| 41 | GPIO18/SPICLKA/LINTXA/XCLKOUT | bidirectional | General-purpose I/O 18; alternate functions SPI-A clock, LIN transmit and XCLKOUT output clock. |
| 42 | GPIO17/SPISOMIA/TZ3 | bidirectional | General-purpose I/O 17; alternate functions SPI-A slave out/master in and trip-zone input 3. |
| 43 | GPIO8/EPWM5A/ADCSOCAO | bidirectional | General-purpose I/O 8; alternate functions ePWM5A output and ADC start-of-conversion A output. |
| 44 | GPIO25/SPISOMIB | bidirectional | General-purpose I/O 25; alternate function SPI-B slave out/master in. |
| 45 | GPIO44 | bidirectional | General-purpose I/O 44. |
| 46 | GPIO16/SPISIMOA/TZ2 | bidirectional | General-purpose I/O 16; alternate functions SPI-A slave in/master out and trip-zone input 2. |
| 47 | GPIO12/TZ1/SCITXDA/SPISIMOB | bidirectional | General-purpose I/O 12; alternate functions trip-zone input 1, SCI transmit and SPI-B slave in/master out. |
| 48 | GPIO41/EPWM7B | bidirectional | General-purpose I/O 41; alternate function ePWM7B output. |
| 49 | GPIO7/EPWM4B/SCIRXDA | bidirectional | General-purpose I/O 7; alternate functions ePWM4B output and SCI receive. |
| 50 | GPIO6/EPWM4A/EPWMSYNCI/EPWMSYNCO | bidirectional | General-purpose I/O 6; alternate functions ePWM4A output and external ePWM sync input/output. |
| 51 | X2 | output | On-chip crystal oscillator output; connect crystal/resonator between X1 and X2, leave unconnected if unused. |
| 52 | X1 | input | 1.8V on-chip crystal oscillator input; connect to GND if unused, never apply 3.3V. |
| 53 | VSS | power_in | Digital ground pin. |
| 54 | VDD | power_in | CPU and logic digital power pin; with internal VREG place a 1.2 uF (minimum) capacitor to ground on each VDD pin. |
| 55 | GPIO19/XCLKIN/SPISTEA/LINRXA/ECAP1 | bidirectional | General-purpose I/O 19; alternate functions external oscillator input, SPI-A slave transmit enable, LIN receive and eCAP1. |
| 56 | GPIO39 | bidirectional | General-purpose I/O 39. |
| 57 | GPIO38/TCK/XCLKIN | bidirectional | General-purpose I/O 38; JTAG test clock with internal pull-up and external oscillator input. |
| 58 | GPIO37/TDO | bidirectional | General-purpose I/O 37; JTAG test data output (8mA drive). |
| 59 | GPIO35/TDI | bidirectional | General-purpose I/O 35; JTAG test data input with internal pull-up. |
| 60 | GPIO36/TMS | bidirectional | General-purpose I/O 36; JTAG test mode select with internal pull-up. |
| 61 | GPIO11/EPWM6B/LINRXA/HRCAP2 | bidirectional | General-purpose I/O 11; alternate functions ePWM6B output, LIN receive and HRCAP2 input. |
| 62 | GPIO5/EPWM3B/SPISIMOA/ECAP1 | bidirectional | General-purpose I/O 5; alternate functions ePWM3B output, SPI-A slave in/master out and eCAP1. |
| 63 | GPIO4/EPWM3A | bidirectional | General-purpose I/O 4; alternate function ePWM3A output and HRPWM channel. |
| 64 | GPIO40/EPWM7A | bidirectional | General-purpose I/O 40; alternate function ePWM7A output and HRPWM channel. |
| 65 | GPIO10/EPWM6A/ADCSOCBO | bidirectional | General-purpose I/O 10; alternate functions ePWM6A output and ADC start-of-conversion B output. |
| 66 | GPIO3/EPWM2B/SPISOMIA/COMP2OUT | bidirectional | General-purpose I/O 3; alternate functions ePWM2B output, SPI-A slave out/master in and comparator 2 output. |
| 67 | GPIO2/EPWM2A | bidirectional | General-purpose I/O 2; alternate function ePWM2A output and HRPWM channel. |
| 68 | GPIO1/EPWM1B/COMP1OUT | bidirectional | General-purpose I/O 1; alternate functions ePWM1B output and comparator 1 direct output. |
| 69 | GPIO0/EPWM1A | bidirectional | General-purpose I/O 0; alternate function ePWM1A output and HRPWM channel. |
| 70 | VDDIO | power_in | Digital I/O buffer and flash power pin; single supply when VREG is enabled, place a decoupling capacitor on each pin. |
| 71 | VSS | power_in | Digital ground pin. |
| 72 | VDD | power_in | CPU and logic digital power pin; with internal VREG place a 1.2 uF (minimum) capacitor to ground on each VDD pin. |
| 73 | VREGENZ | input | Internal VREG enable with internal pull-down; tie to VSS to enable the 1.8V VREG, tie to VDDIO to disable it and use an external 1.8V supply. |
| 74 | GPIO34/COMP2OUT/COMP3OUT | bidirectional | General-purpose I/O 34; alternate functions comparator 2 and comparator 3 direct outputs. |
| 75 | GPIO15/TZ1/LINRXA/SPISTEB | bidirectional | General-purpose I/O 15; alternate functions trip-zone input 1, LIN receive and SPI-B slave transmit enable. |
| 76 | GPIO13/TZ2/SPISOMIB | bidirectional | General-purpose I/O 13; alternate functions trip-zone input 2 and SPI-B slave out/master in. |
| 77 | GPIO14/TZ3/LINTXA/SPICLKB | bidirectional | General-purpose I/O 14; alternate functions trip-zone input 3, LIN transmit and SPI-B clock. |
| 78 | GPIO20/EQEP1A/COMP1OUT | bidirectional | General-purpose I/O 20; alternate functions eQEP1 input A and comparator 1 direct output. |
| 79 | GPIO21/EQEP1B/COMP2OUT | bidirectional | General-purpose I/O 21; alternate functions eQEP1 input B and comparator 2 direct output. |
| 80 | GPIO24/ECAP1/SPISIMOB | bidirectional | General-purpose I/O 24; alternate functions eCAP1 and SPI-B slave in/master out. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-80(12x12) |
| Category | Embedded Processors & Controllers |
| Pins | 80 |
CAD (KiCad official)
- Symbol:
TMS320F28032PNTR - Footprint:
Package_QFP:LQFP-80_12x12mm_P0.5mm - 3D model: LQFP-80(12x12) (KiCad packages3D, STEP)
- 3D model files:
tms320f28032pntr-etched.step/tms320f28032pntr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tms320f28032pntr.step/tms320f28032pntr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (176 pp, sha256
cb9ccecfd6b5c484, retrieved 2026-10-07, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).