component
TMP816PWR
Public Made by Adomby adom
Texas Instruments Brushed DC Motor Drivers, TSSOP-20. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+56@@ -0,0 +1,56 @@+# TMP816PWR++**Texas Instruments** · Brushed DC Motor Drivers · TSSOP-20++TMP816PWR from Texas Instruments, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OUT2P | output | Upper-side driver output for the second H-bridge stage |+| 2 | OUT2N | output | Lower-side driver output for the second H-bridge stage |+| 3 | VCC | power_in | Power supply input; connect 0.1 μF to 1 μF decoupling capacitor with thick pattern and shortest route |+| 4 | VLIM | input | Current limiter threshold input; activates current limiter when SENSE voltage exceeds VLIM |+| 5 | SENSE | input | Current sense input from series resistor in motor circuit; connect to GND when not used |+| 6 | RMI | input | Minimum speed setting input; connect to 6VREG when not used |+| 7 | VTH | input | Speed control voltage input filtered from PWM signal; supports 20 kHz to 100 kHz PWM input frequency |+| 8 | CPWM | output | PWM frequency setting output; connect external capacitor (100 pF for 25 kHz oscillation frequency) |+| 9 | FG | tri_state | Open collector motor speed feedback output; detects rotation speed via phase shift |+| 10 | RD | tri_state | Open collector lock detection output; outputs low during rotation and high at motor stop |+| 11 | IN- | input | Hall sensor negative input terminal |+| 12 | HB | output | Hall sensor bias output; provides 1.5-V constant-voltage supply for Hall elements |+| 13 | IN+ | input | Hall sensor positive input; keep traces short to minimize noise; ensure signal amplitude exceeds 60 mVp-p |+| 14 | CT | output | Lock detection capacitor connection; external capacitor determines lock detection timeout period |+| 15 | ROFF | input | Reactive current cut-off time setting input; sets soft-switching time to cut reactive current before phase change |+| 16 | 6VREG | power_out | 6-V regulated output for Hall sensor and circuit pull-up supplies; provides 5.8 V to 6.15 V at 5 mA load |+| 17 | SGND | power_in | Ground connection for control circuit power supply system |+| 18 | SS | output | Soft-start capacitor connection; external capacitor between 6VREG and SS sets soft-start time |+| 19 | OUT1N | output | Lower-side driver output for the first H-bridge stage |+| 20 | OUT1P | output | Upper-side driver output for the first H-bridge stage |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-20 |+| Category | Motor Driver ICs |+| Pins | 20 |++## CAD (KiCad official)++- Symbol: `TMP816PWR`+- Footprint: `Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm`+- 3D model: TSSOP-20 (KiCad packages3D, STEP)+- 3D model files: `tmp816pwr-etched.step` / `tmp816pwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tmp816pwr.step` / `tmp816pwr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tmp816.pdf) (22 pp, sha256 `891426576b1d704d`, retrieved 2026-10-07, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tmp816pwr-datasheet.pdf)
page.jsonadded+270@@ -0,0 +1,270 @@+{+ "slug": "tmp816pwr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Brushed DC Motor Drivers, TSSOP-20. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "motor driver ics",+ "tmp816pwr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tmp816pwr.kicad_sym",+ "tmp816pwr.kicad_mod",+ "tmp816pwr.glb",+ "tmp816pwr.step",+ "tmp816pwr.lbr",+ "docs/hero.png",+ "docs/tmp816pwr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tmp816pwr-hero.glb",+ "tmp816pwr-hero.overlay.json"+ ],+ "component": {+ "mpn": "TMP816PWR",+ "manufacturer": "Texas Instruments",+ "package": "TSSOP-20",+ "pin_count": 20,+ "category": "Motor Driver ICs",+ "subcategory": "Brushed DC Motor Drivers",+ "datasheet": "https://www.ti.com/lit/ds/symlink/tmp816.pdf",+ "parts": {+ "symbol": "tmp816pwr.kicad_sym",+ "footprint": "tmp816pwr.kicad_mod",+ "model_3d": "tmp816pwr-hero.glb",+ "model_3d_plain": "tmp816pwr.glb",+ "model_3d_step": "tmp816pwr-etched.step",+ "model_3d_step_plain": "tmp816pwr.step",+ "lbr": "tmp816pwr.lbr"+ },+ "distributor_links": {+ "lcsc": "C1880301",+ "digikey": "296-TMP816PWRTR-ND",+ "mouser": "595-TMP816PWR"+ },+ "distributor_check": {+ "checked_at": "2026-10-07T01:57:28Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-TMP816PWRTR-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "595-TMP816PWR",+ "status": "found",+ "lifecycle": "End of Life"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "OUT2P",+ "type": "output",+ "description": "Upper-side driver output for the second H-bridge stage"+ },+ {+ "number": "2",+ "name": "OUT2N",+ "type": "output",+ "description": "Lower-side driver output for the second H-bridge stage"+ },+ {+ "number": "3",+ "name": "VCC",+ "type": "power_in",+ "description": "Power supply input; connect 0.1 μF to 1 μF decoupling capacitor with thick pattern and shortest route"+ },+ {+ "number": "4",+ "name": "VLIM",+ "type": "input",+ "description": "Current limiter threshold input; activates current limiter when SENSE voltage exceeds VLIM"+ },+ {+ "number": "5",+ "name": "SENSE",+ "type": "input",+ "description": "Current sense input from series resistor in motor circuit; connect to GND when not used"+ },+ {+ "number": "6",+ "name": "RMI",+ "type": "input",+ "description": "Minimum speed setting input; connect to 6VREG when not used"+ },+ {+ "number": "7",+ "name": "VTH",+ "type": "input",+ "description": "Speed control voltage input filtered from PWM signal; supports 20 kHz to 100 kHz PWM input frequency"+ },+ {+ "number": "8",+ "name": "CPWM",+ "type": "output",+ "description": "PWM frequency setting output; connect external capacitor (100 pF for 25 kHz oscillation frequency)"+ },+ {+ "number": "9",+ "name": "FG",+ "type": "tri_state",+ "description": "Open collector motor speed feedback output; detects rotation speed via phase shift"+ },+ {+ "number": "10",+ "name": "RD",+ "type": "tri_state",+ "description": "Open collector lock detection output; outputs low during rotation and high at motor stop"+ },+ {+ "number": "11",+ "name": "IN–",+ "type": "input",+ "description": "Hall sensor negative input terminal"+ },+ {+ "number": "12",+ "name": "HB",+ "type": "output",+ "description": "Hall sensor bias output; provides 1.5-V constant-voltage supply for Hall elements"+ },+ {+ "number": "13",+ "name": "IN+",+ "type": "input",+ "description": "Hall sensor positive input; keep traces short to minimize noise; ensure signal amplitude exceeds 60 mVp-p"+ },+ {+ "number": "14",+ "name": "CT",+ "type": "output",+ "description": "Lock detection capacitor connection; external capacitor determines lock detection timeout period"+ },+ {+ "number": "15",+ "name": "ROFF",+ "type": "input",+ "description": "Reactive current cut-off time setting input; sets soft-switching time to cut reactive current before phase change"+ },+ {+ "number": "16",+ "name": "6VREG",+ "type": "power_out",+ "description": "6-V regulated output for Hall sensor and circuit pull-up supplies; provides 5.8 V to 6.15 V at 5 mA load"+ },+ {+ "number": "17",+ "name": "SGND",+ "type": "power_in",+ "description": "Ground connection for control circuit power supply system"+ },+ {+ "number": "18",+ "name": "SS",+ "type": "output",+ "description": "Soft-start capacitor connection; external capacitor between 6VREG and SS sets soft-start time"+ },+ {+ "number": "19",+ "name": "OUT1N",+ "type": "output",+ "description": "Lower-side driver output for the first H-bridge stage"+ },+ {+ "number": "20",+ "name": "OUT1P",+ "type": "output",+ "description": "Upper-side driver output for the first H-bridge stage"+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [],+ "pages_sent": 22,+ "cost_usd": 0.1198,+ "at": "2026-10-07T01:57:10"+ },+ "datasheet": {+ "url": "https://www.ti.com/lit/ds/symlink/tmp816.pdf",+ "pages": 22,+ "sha256": "891426576b1d704d",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 20,+ "described": 20,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tmp816pwr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 6.5,+ 1.2+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "97339947f3a7196470ec2f1d9f9b92bb2fc2ab66ad53be0cf105192585ef3c9a",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tmp816pwr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 6.5,+ 1.2+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "7c58a32cc451dcf0f98e670162eba0134eaf64229cca53fce0eb2598d42c4d3e",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}