TMI3113

{
 "schema": "adom.pads/1",
 "slug": "tmi3113",
 "footprint": "SOT-23-6",
 "generated_from": {
  "footprint": "SOT-23-6@sha256:f341c73aac9dcb55",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -1.1375,
   -0.95
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOT-23-6@sha256:f341c73aac9dcb55"
 },
 "pad_count": 6,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "EN",
   "type": "input",
   "description": "Chip enable pin. Drive above EN rising threshold (typ 1.1V @VIN=5V, 0.9V @VIN=3.3V) to turn the part on; drive below EN falling threshold (typ 1.0V @VIN=5V, 0.9V @VIN=3.3V) to turn it off. Do not leave floating. EN leakage <=1uA. Absolute max 7V.",
   "is_pin1": true,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "GND",
   "type": "power_in",
   "description": "Device ground return pin. All internal references and MOSFET source (low-side) currents return through this pin.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "LX",
   "type": "output",
   "description": "Power switch (inductor) node. Connects to the drains of the internal P-channel high-side and N-channel low-side MOSFETs. Connect the external inductor here. Absolute max -0.3V to 7V (transient -3.5V to 8.5V for <5ns). PMOS RDS(on) ~95mOhm, NMOS RDS(on) ~50mOhm, peak current limit ~3.5A (typ).",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "VIN",
   "type": "power_in",
   "description": "Analog and power supply input pin. Operating range 2.7V to 5.5V; input OVP threshold typ 6.1V; input UVLO typ 2.5V rising with ~500mV hysteresis; absolute max 7V. Bypass with a low-ESR ceramic capacitor (22uF X5R/X7R typical) close to the pin.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "PG",
   "type": "output",
   "description": "Power-Good open-drain output (TMI3113 only). Goes high-impedance when the output voltage rises above ~91% of the regulated nominal voltage and is pulled low when the output falls below the threshold or when EN is pulled low. Sink capability 2mA max. Requires an external pull-up resistor.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "FB",
   "type": "input",
   "description": "Output voltage feedback pin. Internal reference is 0.600V (typ); an external resistor divider from VOUT programs the output per VOUT = 0.6 x (1 + R1/R2). In PFM/no-load operation FB regulates slightly above 0.6V (typ 0.609V). Absolute max 7V.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}