Generated by kicad-footprint-generator · KiCad file format 20260206
TMCS1107A2BQDRQ1
Texas Instruments · Current Sensors · SOIC-8
TMCS1107A2BQDRQ1 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN+ | input | Input current positive pin; current polarity is considered positive when flowing into the positive input pin, and IN+ pins 1 and 2 are tied internally to the isolated input conductor. |
| 2 | IN+ | input | Input current positive pin; current polarity is considered positive when flowing into the positive input pin, and it is the second of two IN+ pins on the isolated input conductor. |
| 3 | IN- | input | Input current negative pin; it is one of two IN- pins on the isolated input conductor, and VIN- is referenced to GND (pin 5) with a recommended operating range of -420 V to 420 VPK. |
| 4 | IN- | input | Input current negative pin; it is the second of two IN- pins on the isolated input conductor, and VIN- is referenced to GND (pin 5) with a recommended operating range of -420 V to 420 VPK. |
| 5 | GND | power_in | Analog ground reference for the low-voltage side; the input voltages VIN+ and VIN- are measured relative to this pin, and the absolute maximum VOUT and NC voltages are referenced to it. |
| 6 | NC | unconnected | No connect; the pin can tolerate a capacitive or resistive connection to GND or VS (TI recommends a short to GND if acceptable), with an input impedance of 1 MΩ over GND < VNC < VS and an absolute maximum range of GND - 0.3 V to (VS) + 0.3 V. |
| 7 | VOUT | output | Analog output voltage proportional to the input current; it is limited to GND - 0.3 V to (VS) + 0.3 V absolute maximum, the maximum capacitive load is 1 nF with no sustained oscillation, and the output is a high-impedance state until about 25 ms after VS reaches 3 V. |
| 8 | VS | power_in | Analog power supply; the operating supply range is 3 V to 5.5 V for the TMCS1107A2B-Q1 variant, with an absolute maximum of 6 V referenced to GND, and a 0.1-µF low-ESR decoupling capacitor is recommended between VS and GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Magnetic Sensors |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Sensitivity error, 0.05 V ≤ VOUT ≤ VS, 0.2 V, TA = 25°C | -1.2 | 0.4 | 1.2 | % | 0.05 V ≤ VOUT ≤ VS, 0.2 V, TA= 25ºC | 8 | |
| Sensitivity error incl. lifetime and environmental drift, 0.05 V ≤ VOUT ≤ VS, 0.2 V, TA = 25°C | -1.8 | 0.7 | 1.8 | % | 0.05 V ≤ VOUT ≤ VS, 0.2 V, TA= 25ºC | 8 | |
| Sensitivity error, 0.05 V ≤ VOUT ≤ VS, 0.2 V, TA = -40°C to +85°C | -1.8 | 0.7 | 1.8 | % | 0.05 V ≤ VOUT ≤ VS, 0.2 V, TA= -40ºC to +85ºC | 8 | |
| Sensitivity error, 0.05 V ≤ VOUT ≤ VS, 0.2 V, TA = -40°C to +125°C | -2.25 | 0.9 | 2.25 | % | 0.05 V ≤ VOUT ≤ VS, 0.2 V, TA= -40ºC to +125ºC | 8 | |
| Nonlinearity error | -0.5 | 0.5 | % | VOUT = 0.5 V to VS, 0.5 V | 8 | ||
| Output voltage offset error (A2B) | VOE | -10 | 2 | 10 | mV | 8 | |
| Output voltage offset drift (A2B) | -40 | 10 | 40 | µV/℃ | TA= -40ºC to +125ºC | 8 | |
| Offset error, RTI (A2B) | IOS | -100 | 20 | 100 | mA | 9 | |
| Offset error temperature drift, RTI (A2B) | -400 | 100 | 400 | µA/°C | TA= -40ºC to +125ºC | 9 | |
| Power-supply rejection ratio | PSRR | -6.5 | 1 | 6.5 | mV/V | VS = 3 V to 5.5 V, TA= -40ºC to +125ºC | 9 |
| Allowable continuous RMS current, TA = 25°C | IIN,max | 30 | A | TA= 25ºC | 9 | ||
| Allowable continuous RMS current, TA = 85°C | IIN,max | 25 | A | TA= 85ºC | 9 | ||
| Allowable continuous RMS current, TA = 105°C | IIN,max | 22.5 | A | TA= 105ºC | 9 | ||
| Allowable continuous RMS current, TA = 125°C | IIN,max | 16 | A | TA= 125ºC | 9 | ||
| Quiescent current, TA = 25°C | IQ | 4.5 | 5.5 | mA | TA = 25ºC | 10 | |
| Quiescent current, over temperature | IQ | 6 | mA | TA = -40ºC to +125ºC | 10 | ||
| Operating supply voltage (TMCS1107A1B/U-Q1 to A3B/U-Q1) | VS | 3 | 5 | 5.5 | V | 4 | |
| Input voltage, VIN+ and VIN- (relative to GND pin 5) | VIN+,VIN- | -420 | 420 | VPK | Relative to pin 5 (GND) | 4 | |
| Operating free-air temperature | TA | -40 | 125 | °C | 4 | ||
| Supply voltage (absolute maximum; minimum is GND, 0.3 V) | VS | 6 | V | 4 | |||
| Junction temperature | TJ | -65 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 36.6 | °C/W | Applies when device mounted on TMCS1107EVM | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 50.7 | °C/W | Applies when device mounted on TMCS1107EVM | 5 | ||
| Junction-to-board thermal resistance | RθJB | 9.6 | °C/W | Applies when device mounted on TMCS1107EVM | 5 | ||
| Junction-to-top characterization parameter | ΨJT | -0.1 | °C/W | Applies when device mounted on TMCS1107EVM | 5 | ||
| Junction-to-board characterization parameter | ΨJB | 11.7 | °C/W | Applies when device mounted on TMCS1107EVM | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | path directly underneath the package lead footprint, and use a merged copper input trace for both the IN+ and | 32 |
CAD (KiCad official)
- Symbol:
TMCS1107A2BQDRQ1 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
tmcs1107a2bqdrq1-etched.step/tmcs1107a2bqdrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tmcs1107a2bqdrq1.step/tmcs1107a2bqdrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
963e8cdc0b5b235e, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).