main
History Download
Ray Publish 0.1.0 b37937a

TM512AC0

TM(Shenzhen Titan Micro Elec) · LED Drivers · SOP-8

TM512AC0 from TM(Shenzhen Titan Micro Elec), in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 GND power_in Negative power supply pin; all voltages are specified relative to system ground, and the datasheet requires controller and ICs to share a common ground.
2 ADRO output Address write-code line output; used for A/B-line address programming and is driven to 10 mA minimum low-level output current at Vo = 0.4 V.
3 DO output Decoded forwarding output that converts the DMX512 channel data to a single-wire return-to-zero code to drive the company's TM18 and TM19 series LED ICs (e.g., TM1804, TM1925D, TM1926D); minimum 10 mA low-level (Vo = 0.4 V) and high-level (Vo = 4 V) output current.
4 TST input Test pin with an internal pull-down; it is not part of normal operation.
5 ADRI input Address write-code line input with internal pull-up; high-level input requires at least 0.7Vdd and low-level input must not exceed 0.3Vdd.
6 AI input Positive differential signal input of the DMX512 bus with internal pull-up; differential input common-mode voltage up to 12 V, threshold ±0.2 V, and input impedance 280 kΩ typical.
7 BI input Negative differential signal input of the DMX512 bus with internal pull-down; it is the inverse of AI, with the same common-mode (up to 12 V) and threshold (±0.2 V) limits.
8 VDD power_in Positive logic supply pin; the recommended Vdd is 3.8 V (min) to 6 V (max), with an absolute-maximum range of 5.5 V to 6.5 V.

Key specifications

Parameter Value
Manufacturer TM(Shenzhen Titan Micro Elec)
Package SOP-8
Category Nixie Tube Driver/LED Driver
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
逻辑电源电压 Vdd 5.5 6.5 V 3
工作温度 Topt -40 85 ℃ 3
储存温度 Tstg -55 150 ℃ 3
抗静电 ESD ESD 8000 V 3
封装功耗 Pd 400 mW 3
逻辑电源电压 Vdd 3.8 5.5 6 V , 3
低电平输入电压 Vil 0 V , 3
低电平输出电流 Iol 10 mA Vo=0.4V, DO, ADRO 3
高电平输出电流 Ioh 10 mA Vo=4V, DO, ADRO 3
输入电流 Ii -1 1 µA 3
差分输入共模电压 Vcm 12 V 3
差分输入电流 Iab 28 µA VDD=5V 3
差分输入临限电压 Vth -0.2 0.2 V 0V<Vcm<12V 3
差分输入迟滞电压 70 mV Vcm=0V 3
差分输入阻抗 Rin 280 KΩ 3
动态电流损耗 IDDdyn 4 mA VDD=5V 无负载 3
消耗功率 PD 400 mW TA=25℃ 3
热阻值 Rth(j-a) 80 190 ℃/W 3
比特率 200 500 1000 Kbps 4
位时间 1 2 5 μs 4
起始位 S 1 2 5 μs 4
8位数据 D0~D7 1 2 5 μs 4
2位停止位 T 2 4 10 μs 4
复位前标记 1 0 1e+06 μs 4
复位信号 2 88 1e+06 μs 4
复位后标记 3 8 1e+06 μs 4
字段 4 11 22 55 μs 4
字段之间的占空 5 0 1e+06 μs 4
数据包的长度 6 1024 1e+06 μs 4
复位信号间隔 7 4096 1e+06 μs 4

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: TM512AC0
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8, generated on the KiCad land (body 3.9 x 4.9 mm, terminals on the pads, 1.65 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: tm512ac0-etched.step / tm512ac0-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tm512ac0.step / tm512ac0.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TM(Shenzhen Titan Micro Elec) datasheet (7 pp, sha256 60da2018d396d650, retrieved 2026-11-13, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF