main
Ray Publish 0.1.0 36e3e32

TLV9030L1QDCKRQ1

Texas Instruments · Integrated Circuits (ICs) · 6-TSSOP, SC-88, SOT-363

TLV9030L1QDCKRQ1 from Texas Instruments, in a 6-TSSOP, SC-88, SOT-363. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 IN+ input Non-inverting (+) input; rail-to-rail and fault-tolerant, it tolerates up to 6V without damage and must stay within -0.2V to 5.5V from V- under recommended operating conditions.
2 V- power_in Negative supply voltage; the supply span (V+) - (V-) must be between 1.65V and 5.5V.
3 IN- input Inverting (-) input; must stay within -0.2V to 5.5V from V- under recommended operating conditions.
4 OUT output Push-pull output on the TLV903xL-Q1 that can sink and source up to 85mA, latching on the low-to-high output transition.
5 CLR input Clear input that resets the output latch on a falling edge; its range is -0.2V to 5.5V from V-.
6 V+ power_in Positive supply voltage; the supply span (V+) - (V-) must be between 1.65V and 5.5V.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package 6-TSSOP, SC-88, SOT-363
Category Integrated Circuits (ICs)
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VS 1.65 5.5 V VS = (V+) - (V-) 5
Input voltage range (IN+, IN-, CLR) from (V-) -0.2 5.5 V 5
Output voltage range, open drain output, from (V-) 0 5.5 V open drain output 5
Ambient temperature TA -40 125 °C 5
Supply voltage VS -0.3 6 V VS = (V+), (V-) 5
Input pins (IN+, IN-, CLR) from (V-) -0.3 6 V 5
Current into input pins (IN+, IN-, CLR) -10 10 mA 5
Output (OUT) from (V-) -0.3 6 V 5
Output short circuit duration 10 s short to (V-) or (V+) 5
Junction temperature TJ 150 °C 5
Storage temperature Tstg -65 150 °C 5
Electrostatic discharge, human-body model (HBM) V(ESD) -2000 2000 V per AEC Q100-002 5
Electrostatic discharge, charged-device model (CDM) V(ESD) -1000 1000 V per AEC Q100-011 5
Input threshold voltage VT -1.75 0.3 1.75 mV VS = 1.8V and 5V 7
Input threshold voltage VT -2.25 2.25 mV VS = 1.8V and 5V, TA = -40°C to +125°C 7
Input threshold voltage drift dVT/dT -0.5 0.5 µV/°C VS = 1.8V and 5V, TA = -40°C to +125°C 7
Quiescent current per comparator IQ 22 30 µA VS = 1.8V and 5V, No Load, Output Low 7
Quiescent current per comparator IQ 42 µA VS = 1.8V and 5V, No Load, Output Low, TA = -40°C to +125°C 7
Power-supply rejection ratio (push-pull) PSRR 75 95 dB VS = 1.8V to 5V, TA = -40°C to +125°C (push-pull only) 7
Power-supply rejection ratio (open drain) PSRR 80 95 dB VS = 1.8V to 5V, TA = -40°C to +125°C (open drain only) 7
Voltage input high threshold of CLR VIH_CLR 1.2 V 7
Voltage input low threshold of CLR VIL_CLR 0.6 V 7
Common-mode rejection ratio (5V) CMRR 60 70 dB VS = 5V, (V-), 0.2V < VCM < (V+) + 0.2V, TA = -40°C to +125°C 7
Common-mode rejection ratio (1.8V) CMRR 50 60 dB VS = 1.8V, (V-), 0.2V < VCM < (V+) + 0.2V, TA = -40°C to +125°C 7
Voltage swing from (V-) VOL 75 125 mV ISINK = 4mA, TA = 25°C 7
Voltage swing from (V-) VOL 175 mV ISINK = 4mA, TA = -40°C to +125°C 7
Voltage swing from (V+) VOH 75 125 mV ISOURCE = 4mA, TA = 25°C (push-pull only) 7
Voltage swing from (V+) VOH 175 mV ISOURCE = 4mA, TA = -40°C to +125°C (push-pull only) 7
Open-drain output leakage current ILKG 100 pA VPULLUP = (V+), TA = 25°C 7
Short-circuit current (sinking) ISC 75 85 mA VS = 5V, Sinking 7
Short-circuit current (sourcing) ISC 75 85 mA VS = 5V, Sourcing (push-pull only) 7
Propagation delay time, high-to-low (open-drain only) TPD-HL 110 ns VID = -100mV, CLR = 0V, RP = 2.5KΩ 8
Propagation delay time, low-to-high (push-pull only) TPD-LH 125 ns VID = +100mV, CLR = 0V 8
Clear fall to latch reset propagation delay time TPD-CLR-F 25 70 ns CLR = 1.8V to 5V 8
Minimum clear hold pulse time CLR_Min 10 ns CLR = 1.8V to 5V 8
5V output fall time, 80% to 20% TFALL 3 ns VID = -100mV 8
5V output rise time, 20% to 80% (push-pull only) TRISE 3 ns VID = +100mV, push-pull only 8
Power on time PON 35 µs 8
Input bias current IB 5 pA VCM = VS/2 7
Input offset current IOS 1 pA VCM = VS/2 7
Input capacitance, differential CID 2 pF VCM = VS/2 7
Input capacitance, common mode CIC 3 pF VCM = VS/2 7
Power-on reset voltage (positive) VPOR 1.25 V 7
Junction-to-ambient thermal resistance (DCK, SC-70) θJA 210.5 °C/W 6
Junction-to-case (top) thermal resistance (DCK, SC-70) θJC(top) 143.9 °C/W 6
Junction-to-board thermal resistance (DCK, SC-70) θJB 64.7 °C/W 6
Junction-to-top characterization parameter (DCK, SC-70) ψJT 46.1 °C/W 6
Junction-to-board characterization parameter (DCK, SC-70) ψJB 64.5 °C/W 6

CAD (Adom-generated)

  • Symbol: TLV9030L1QDCKRQ1
  • Footprint: Adom_Gen:Texas_Instruments_TLV9030_a02d67
  • 3D model: generated to fit the land (STEP)
  • 3D model files: tlv9030l1qdckrq1-etched.step / tlv9030l1qdckrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tlv9030l1qdckrq1.step / tlv9030l1qdckrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (36 pp, sha256 04bf1a8ebbea4277, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.

Datasheet PDF