main
Ray Publish 0.1.0 767b771

TLD5190QUXUMA1

Infineon Technologies · LED Drivers · TQFP-48(7x7)

TLD5190QUXUMA1 from Infineon Technologies, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 n.c. unconnected Not connected; tie to AGND on the layout.
2 HSGD1 output High-side gate driver output 1 drives the top n-channel MOSFET with a voltage equal to VIVCC_EXT superimposed on SWN1; connect to the gate of the external switching MOSFET.
3 BST1 bidirectional Bootstrap capacitor pin for internal biasing and HSGD1 drive; bypass to SWN1 with a capacitor close to the pin and do not leave open.
4 SWN1 bidirectional Switch node 1 swings from a diode voltage drop below ground up to VIN.
5 PGND1 power_in Power ground for the power potential; connect externally close to the chip.
6 LSGD1 output Low-side gate driver output 1 drives the low-side n-channel MOSFET between GND and VIVCC_EXT; connect to the gate of the external switching MOSFET.
7 LSGD2 output Low-side gate driver output 2 drives the low-side n-channel MOSFET between GND and VIVCC_EXT; connect to the gate of the external switching MOSFET.
8 PGND2 power_in Power ground for the power potential; connect externally close to the chip.
9 SWN2 bidirectional Switch node 2 swings from ground up to a diode voltage drop above VOUT.
10 BST2 bidirectional Bootstrap capacitor pin for internal biasing and HSGD2 drive; bypass to SWN2 with a capacitor close to the pin and do not leave open.
11 HSGD2 output High-side gate driver output 2 drives the top n-channel MOSFET with a voltage equal to VIVCC_EXT superimposed on SWN2; connect to the gate of the external switching MOSFET.
12 n.c. unconnected Not connected; tie to AGND on the layout.
13 FBH input Output current feedback positive, non-inverting input (+).
14 FBL input Output current feedback negative, inverting input (-).
15 n.c. unconnected Not connected; tie to AGND on the layout.
16 IOUTMON output Output current monitor producing 200 mV + 8 times VFBH-FBL, equal to 1.4 V at VFBH-FBL = 150 mV.
17 SWCS input Inductor current sense input, non-inverting input (+); route as differential net with SGND on the layout.
18 SGND power_in Inductor current sense ground, inverting input (-); route as differential net with SWCS on the layout.
19 COMP output Compensation network pin; connect an R and C network to the pin for stability and phase margin adjustment.
20 VFB input Voltage loop feedback pin intended to set output protection functions.
21 VREF power_in Voltage reference output supplying an accurate 2 V for standalone analog dimming and LED temperature compensation; bypass with 100 nF close to the pin and do not leave open.
22 SET input Analog current sense adjustment pin; a voltage VSET between 0.2 V and 1.5 V adjusts ILED or VOUT in a linear relation.
23 TEST1 passive Test pin used for Infineon end-of-line test; connect to GND in the application.
24 PWMI input Control input for PWM dimming; digital input 5 V or 3.3 V with integrated pull-down.
25 TEST2 passive Test pin used for Infineon end-of-line test; connect to GND in the application.
26 VSS power_in Digital GPIO ground reference for the GPIO pins.
27 CLKOUT output Clock output carrying the switching oscillator signal to supply SYNC inputs of other DC/DC devices; disabled during overtemperature.
28 TEST3 passive Test pin used for Infineon end-of-line test; connect to GND in the application.
29 TEST4 passive Test pin used for Infineon end-of-line test; connect to GND in the application.
30 TEST5 passive Test pin used for Infineon end-of-line test; connect to GND in the application.
31 TEST6 passive Test pin used for Infineon end-of-line test; connect to GND in the application.
32 EF2 output Open-drain error flag 2, pulled LOW when an open load, overvoltage or overtemperature occurs.
33 EF1 output Open-drain error flag 1, pulled LOW when an output short to GND or overtemperature occurs.
34 SYNC input Synchronization input with integrated pull-down; apply an external clock signal for synchronization.
35 FREQ input Frequency select input; connect an external resistor to GND to set the switching frequency.
36 INOVLO input Input overvoltage protection pin defining an upper VIN threshold and switching the device off on VIN overvoltage; must not be left open.
37 SPREAD_SPECTRUM input Spread spectrum enable pin with integrated pull-down; enables or disables the spread spectrum function for EMC performance.
38 SOFT_START output Soft-start configuration pin; connect a capacitor CSOFT_START to GND to fix the soft start ramp time.
39 IINMON output Input current monitor output producing 20 times VIIN1-IIN2, equal to 1 V at VIIN1-IIN2 = 50 mV.
40 AGND power_in Analog ground reference for the device.
41 EN/INUVLO input Enable and input undervoltage lockout pin with integrated pull-down for low current consumption mode and external UVLO threshold; must not be left open.
42 IIN1 input Input current monitor positive, non-inverting input (+); connect to VIN if the input current monitor is not needed.
43 IIN2 input Input current monitor negative, inverting input (-); connect to VIN if the input current monitor is not needed.
44 VIN power_in Power supply voltage supplying internal biasing of the device.
45 n.c. unconnected Not connected; tie to AGND on the layout.
46 IVCC power_out Internal LDO output used for internal biasing and gate driver supply; bypass with a capacitor close to the pin and do not leave open.
47 IVCC_EXT input External LDO input to alternatively supply the internal gate drivers; must not be left open and connects to IVCC to use the internal LDO.
48 n.c. unconnected Not connected; tie to AGND on the layout.

Key specifications

Parameter Value
Manufacturer Infineon Technologies
Package TQFP-48(7x7)
Category Display Modules / LED Drivers / Display Drivers
Pins 48

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Startup VVIN(ON) 4.7 V VIN increasing; VEN/INUVLO = HIGH; IVCC = IVCC_EXT = 10 mA; 15
Input Undervoltage switch OFF VVIN(OFF) 4.5 V VIN decreasing; VEN/INUVLO = HIGH; IVCC = IVCC_EXT = 10 mA; 15
Device operating current IVIN(ACTIVE) 4.4 6 mA ACTIVE mode; CLKOUT freq. 300 KHz; VPWMI = 0 V; 15
VIN Sleep mode supply current IVIN(SLEEP) 1.5 µA VEN/INUVLO = 0 V; VIN = 13.5 V; VIVCC = VIVCC_EXT= 0 V; 15
Input Undervoltage falling Threshold VEN/INUVLOth 1.6 1.75 1.9 V 15
EN/INUVLO input Current LOW IEN/INUVLO(LOW) 0.45 0.89 1.34 µA VEN/INUVLO = 0.8 V; 15
EN/INUVLO input Current HIGH IEN/INUVLO(HIGH) 1.1 2.2 3.3 µA VEN/INUVLO = 2 V; 15
SLEEP mode to ACTIVE time tACTIVE 0.7 ms VIVCC = VIVCC_EXT; CIVCC = 10 µF; VIN = 13.5 V; 15
V(FBH-FBL) threshold V(FBH-FBL) 145.5 150 154.5 mV VSET = 2 V; 25
V(FBH-FBL) threshold @ analog dimming 10% V(FBH-FBL)_10 10 15 20 mV VSET = 0.32 V; 25
FBH Bias current @ highside sensing setup IFBH_HSS 65 110 155 µA VFBL = 7 V; VFBH - FBL = 150 mV; 25
FBL Bias current @ highside sensing setup IFBL_HSS 17 30 43 µA VFBL = 7 V; VFBH - FBL = 150 mV; 25
FBH Bias current @ lowside sensing setup IFBH_LSS -7.5 -4 -2.5 µA VFBL = 0 V; VFBH - FBL = 150 mV; 25
FBL Bias current @ lowside sensing setup IFBL_LSS -45 -30 -20 µA VFBL = 0 V; VFBH - FBL = 150 mV; 25
Output Monitor Voltage VIOUTMON 1.33 1.4 1.47 V VFBH - FBL = 150 mV; 25
Maximum BOOST Duty Cycle DBOOST_MAX 89 91 93 % fsw = 300 kHZ; 25
Input Current Sense threshold VIIN1-IIN2 46 50 54 mV 25
Input current Monitor Voltage VIINMON 0.95 1 1.05 V VIIN1 - IIN2 = 50 mV; VIIN1 = VVIN(ON) to 55 V; 25
Switch Peak Over Current Threshold - BOOST VSWCS_boost 40 50 60 mV 25
Switch Peak Over Current Threshold - BUCK VSWCS_buck -60 -50 -40 mV 25
Soft Start pull up current ISoft_Start_PU 22 26 32 µA VSoft_Start = 1 V; 25
Soft Start pull down current ISoft_Start_PD 2.2 2.6 3.2 µA VSoft_Start = 1 V; 25
Soft Start Latch-OFF Threshold VSoft_Start_LOFF 1.65 1.75 1.85 V 26
Soft Start Reset Threshold VSoft_Start_RESET 0.1 0.2 0.3 V 26
Soft Start Voltage during regulation VSoft_Start_reg 1.9 2 2.1 V No Faults 26
Switching Frequency fSW 285 300 315 kHz Tj = 25°C; RFREQ= 37.4 kΩ; 26
SYNC Frequency fSYNC 200 700 kHz 26
SYNC Turn On Threshold VSYNC,ON 2 V 26
SYNC Turn Off Threshold VSYNC,OFF 0.8 V 26
SYNC High Input Current ISYNC,H 15 30 45 µA VSYNC = 2.0 V; 26
SYNC Low Input Current ISYNC,L 6 12 18 µA VSYNC = 0.8 V; 26
Gate Driver undervoltage threshold VBST1,2-VSWN1,2_UVth 3.4 4 V VBST1,2 - VSWN1,2 decreasing; 26
HSGD1,2 NMOS driver on-state resistance (Gate Pull Up) RDS(ON_PU)HS 1.4 2.3 3.7 Ω VBST1,2 - VSWN1,2 = 5 V; I source = 100 mA; 26
HSGD1,2 NMOS driver on-state resistance (Gate Pull Down) RDS(ON_PD)HS 0.6 1.2 2.2 Ω VBST1,2 - VSWN1,2 = 5 V; I sink = 100 mA; 26
LSGD1,2 NMOS driver on-state resistance (Gate Pull Up) RDS(ON_PU)LS 1.4 2.3 3.7 Ω VIVCC_EXT = 5 V; Isource = 100 mA; 26
LSGD1,2 NMOS driver on-state resistance (Gate Pull Down) RDS(ON_PD)LS 0.4 1.2 1.8 Ω VIVCC_EXT = 5 V; Isink = 100 mA; 26
HSGD1,2 Gate Driver peak sourcing current IHSGD1,2_SRC 380 mA VHSGD1,2 - VSWN1,2 = 1 V to 4 V; VBST1,2 - VSWN1,2 = 5 V 26
HSGD1,2 Gate Driver peak sinking current IHSGD1,2_SNK 410 mA VHSGD1,2 - VSWN1,2 = 4 V to 1 V; VBST1,2 - VSWN1,2 = 5 V 26
PWMI Turn On Threshold VPWMI,ON 2 V 30
PWMI Turn Off Threshold VPWMI,OFF 0.8 V 30
PWMI High Input Current IPWMI,H 15 30 45 µA VPWMI = 2.0 V; 30
PWMI Low Input Current IPWMI,L 6 12 18 µA VPWMI = 0.8 V; 30
Source current on SET Pin ISET_source 1 µA VSET = 0.2 V to 1.4 V; 33
IVCC Output Voltage VIVCC 4.8 5 5.2 V VIN= 13.5 V; 0.1 mA ≤ IIVCC ≤ 50 mA; 35
Output Current Limitation ILIM 70 90 110 mA VIVCC = 4 V; 35
Drop out Voltage (VIN - VIVCC) VDR 200 350 mV VIN = 5 V; IIVCC = 10 mA; 35
IVCC Buffer Capacitor CIVCC 10 µF 35
IVCC_EXT Undervoltage Reset switch OFF Threshold VIVCC_EXT_RTH,d 3.7 3.9 4.1 V VIVCC_EXT decreasing; 35
IVCC Undervoltage Reset switch OFF Threshold VIVCC_RTH,d 3.7 3.9 4.1 V VIVCC decreasing; 35
IVCC and IVCC_EXT Undervoltage Hysteresis VIVCCX_HYST 0.3 0.33 0.36 V VIVCC increasing; VIVCC_EXT increasing; 35
VREF voltage VREF 1.94 2 2.06 V 0 ≤ IVREF ≤ 200 µA; 35
Short to GND threshold VVFB_S2G 0.53 0.563 0.59 V VVFB decreasing; 42
Over Temperature Shutdown Tj,SD 160 175 190 °C 42
VFB Over Voltage Feedback Threshold VVFB_OVTH 1.42 1.46 1.5 V 42
Output Over Voltage Feedback Hysteresis VVFB_OVTH,HYS 25 40 58 mV Output Voltage decreasing; 42
Open Load rising Threshold VVFB_OL,rise 1.29 1.34 1.39 V VFBH-FBL = 0 V; 42
Open Load reference Voltage VFBH-FBL VFBH_FBL_OL 15 22.5 mV VFB = 1.4 V; 42
Open Load falling Threshold VVFB_OL,fall 1.23 1.28 1.33 V VFBH-FBL = 0 V; 42
Input Overvoltage rising Threshold VINOVLOth 1.9 2 2.1 V 42
Input Overvoltage Threshold Hysteresis VINOVLO(hyst) 18 40 62 mV 42

CAD (KiCad official)

  • Symbol: TLD5190QUXUMA1
  • Footprint: Package_QFP:TQFP-48_7x7mm_P0.5mm
  • 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
  • 3D model files: tld5190quxuma1-etched.step / tld5190quxuma1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tld5190quxuma1.step / tld5190quxuma1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Infineon Technologies datasheet (59 pp, sha256 a11dab213dca0565, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF