main
Ray
Publish 0.1.0
e6d18d4
TLC5917IN
Texas Instruments · LED Drivers · PDIP-16
TLC5917IN from Texas Instruments, in a PDIP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground for control logic and current sink. |
| 2 | SDI | input | Serial-data input to the shift register, with VIH of 0.7 × VDD and VIL of 0.3 × VDD. |
| 3 | CLK | input | Clock input for data shift on the rising edge, with VIH of 0.7 × VDD and VIL of 0.3 × VDD, and a clock frequency up to 25 MHz in the absolute maximum ratings. |
| 4 | LE(ED1) | input | Data strobe input: serial data is transferred to the latch while LE is high and latched when it goes low, and it also serves as a control input for Error Detection Mode and Current Adjust Mode, with an internal pulldown. |
| 5 | OUT0 | output | Constant-current output channel 0, rated for up to 120 mA output current and 20 V output voltage. |
| 6 | OUT1 | output | Constant-current output channel 1, rated for up to 120 mA output current and 20 V output voltage. |
| 7 | OUT2 | output | Constant-current output channel 2, rated for up to 120 mA output current and 20 V output voltage. |
| 8 | OUT3 | output | Constant-current output channel 3, rated for up to 120 mA output current and 20 V output voltage. |
| 9 | OUT4 | output | Constant-current output channel 4, rated for up to 120 mA output current and 20 V output voltage. |
| 10 | OUT5 | output | Constant-current output channel 5, rated for up to 120 mA output current and 20 V output voltage. |
| 11 | OUT6 | output | Constant-current output channel 6, rated for up to 120 mA output current and 20 V output voltage. |
| 12 | OUT7 | output | Constant-current output channel 7, rated for up to 120 mA output current and 20 V output voltage. |
| 13 | OE(ED2) | input | Output enable: when active (low) the output drivers are enabled and when high all outputs are blanked, also serving as a control input for Error Detection Mode and Current Adjust Mode, with an internal pullup. |
| 14 | SDO | output | Serial-data output to the following SDI of the next driver IC or to the microcontroller. |
| 15 | R-EXT | input | Connect an external resistor to ground to set the output current for all channels. |
| 16 | VDD | power_in | Supply voltage, recommended operating range 3 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-16 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | 0 | 7 | V | 4 | ||
| Input voltage | VI | -0.4 | V | max VDD + 0.4 V | 4 | ||
| Output voltage | VO | -0.5 | 20 | V | 4 | ||
| Clock frequency | fclk | 25 | MHz | 4 | |||
| Output current | IOUT | 120 | mA | 4 | |||
| GND terminal current | IGND | 960 | mA | 4 | |||
| Operating free-air temperature | TA | -40 | 125 | °C | 4 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 4 | ||
| Supply voltage | VDD | 3 | 5.5 | V | 4 | ||
| Supply voltage to output pins OUT0-OUT7 | VO | 20 | V | 4 | |||
| Output current | IO | 3 | mA | VO >= 0.6 V, DC test circuit | 4 | ||
| Output current | IO | 120 | mA | VO >= 1 V, DC test circuit | 4 | ||
| High-level output current source | IOH | -1 | mA | SDO shorted to GND | 4 | ||
| Low-level output current sink | IOL | 1 | mA | SDO shorted to VCC | 4 | ||
| High-level input voltage | VIH | 0.7 | × VDD | CLK, OE(ED2), LE(ED1), and SDI | 4 | ||
| Low-level input voltage | VIL | 0 | 0.3 | × VDD | CLK, OE(ED2), LE(ED1), and SDI | 4 | |
| Junction-to-ambient thermal resistance | RθJA | 51.8 | °C/W | N package (PDIP-16) | 4 | ||
| Output leakage current | Ileak | 0.5 | μA | VDD = 3 V, VOH = 17 V, TJ = 25°C | 5 | ||
| Output leakage current | Ileak | 2 | μA | VDD = 3 V, VOH = 17 V, TJ = 125°C | 5 | ||
| Low-level output voltage | VOL | 0.4 | V | VDD = 3 V, SDO, IOH = 1 mA | 5 | ||
| Output current 1 | IO(1) | 1 | 26 | mA | VDD = 3 V, VOUT = 0.6 V, Rext = 720 Ω, CG = 0.992 | 5 | |
| Output current error, die-die | IO(1) | -6 | 6 | % | VDD = 3 V, IOL = 26 mA, VO = 0.6 V, Rext = 720 Ω, TJ = 25°C | 5 | |
| Output current skew, channel-to-channel | IO(1) | -3 | 3 | % | VDD = 3 V, IOL = 26 mA, VO = 0.6 V, Rext = 720 Ω, TJ = 25°C | 5 | |
| Output current 2 | IO(2) | 52 | mA | VDD = 3 V, VO = 0.8 V, Rext = 360 Ω, CG = 0.992 | 5 | ||
| Overtemperature shutdown | Tsd | 150 | 175 | 200 | °C | VDD = 3 V | 5 |
| Restart temperature hysteresis | Thys | 15 | °C | VDD = 3 V | 5 | ||
| Trigger threshold voltage for short-error detection | VOUT,TTh | 2.5 | 2.7 | 3.1 | V | VDD = 3 V, IOUT,target = 3 mA to 120 mA, TLC5917 only | 5 |
| Return threshold voltage for short-error detection | VOUT,RTh | 2.2 | V | VDD = 3 V, IOUT,target = 3 mA to 120 mA, TLC5917 only | 5 | ||
| Supply current, Rext = Open | IDD | 5 | 10 | mA | VDD = 3 V | 5 | |
| Supply current, Rext = 720 Ω | IDD | 8 | 14 | mA | VDD = 3 V | 5 | |
| Supply current, Rext = 360 Ω | IDD | 11 | 18 | mA | VDD = 3 V | 5 | |
| Supply current, Rext = 180 Ω | IDD | 16 | 22 | mA | VDD = 3 V | 5 | |
| Output leakage current | Ileak | 0.5 | μA | VDD = 5.5 V, VOH = 17 V, TJ = 25°C | 6 | ||
| Output leakage current | Ileak | 2 | μA | VDD = 5.5 V, VOH = 17 V, TJ = 125°C | 6 | ||
| Low-level output voltage | VOL | 0.4 | V | VDD = 5.5 V, SDO, IOH = 1 mA | 6 | ||
| Output current 1 | IO(1) | 1 | 26 | mA | VDD = 5.5 V, VOUT = 0.6 V, Rext = 720 Ω, CG = 0.992 | 6 | |
| Output current error, die-die | IO(1) | -6 | 6 | % | VDD = 5.5 V, IOL = 26 mA, VO = 0.6 V, Rext = 720 Ω, TJ = 25°C | 6 | |
| Output current skew, channel-to-channel | IO(1) | -3 | 3 | % | VDD = 5.5 V, IOL = 26 mA, VO = 0.6 V, Rext = 720 Ω, TJ = 25°C | 6 | |
| Output current 2 | IO(2) | 52 | mA | VDD = 5.5 V, VO = 0.8 V, Rext = 360 Ω, CG = 0.992 | 6 | ||
| Overtemperature shutdown | Tsd | 150 | 175 | 200 | °C | VDD = 5.5 V | 6 |
| Restart temperature hysteresis | Thys | 15 | °C | VDD = 5.5 V | 6 | ||
| Trigger threshold voltage for short-error detection | VOUT,TTh | 2.5 | 2.7 | 3.1 | V | VDD = 5.5 V, IOUT,target = 3 mA to 120 mA, TLC5917 only | 6 |
| Return threshold voltage for short-error detection | VOUT,RTh | 2.2 | V | VDD = 5.5 V, IOUT,target = 3 mA to 120 mA, TLC5917 only | 6 | ||
| Supply current, Rext = Open | IDD | 6 | 10 | mA | VDD = 5.5 V | 6 | |
| Supply current, Rext = 720 Ω | IDD | 11 | 14 | mA | VDD = 5.5 V | 6 | |
| Supply current, Rext = 360 Ω | IDD | 13 | 18 | mA | VDD = 5.5 V | 6 | |
| Supply current, Rext = 180 Ω | IDD | 19 | 24 | mA | VDD = 5.5 V | 6 |
CAD (KiCad official)
- Symbol:
TLC5917IN - Footprint:
Package_DIP:DIP-16_W7.62mm - 3D model: PDIP-16 (KiCad packages3D, STEP)
- 3D model files:
tlc5917in-etched.step/tlc5917in-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tlc5917in.step/tlc5917in.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
f257e916f7b5d37b, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TLC5917IN
**Texas Instruments** · LED Drivers · PDIP-16
TLC5917IN from Texas Instruments, in a PDIP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground for control logic and current sink. |
| 2 | SDI | input | Serial-data input to the shift register, with VIH of 0.7 × VDD and VIL of 0.3 × VDD. |
| 3 | CLK | input | Clock input for data shift on the rising edge, with VIH of 0.7 × VDD and VIL of 0.3 × VDD, and a clock frequency up to 25 MHz in the absolute maximum ratings. |
| 4 | LE(ED1) | input | Data strobe input: serial data is transferred to the latch while LE is high and latched when it goes low, and it also serves as a control input for Error Detection Mode and Current Adjust Mode, with an internal pulldown. |
| 5 | OUT0 | output | Constant-current output channel 0, rated for up to 120 mA output current and 20 V output voltage. |
| 6 | OUT1 | output | Constant-current output channel 1, rated for up to 120 mA output current and 20 V output voltage. |
| 7 | OUT2 | output | Constant-current output channel 2, rated for up to 120 mA output current and 20 V output voltage. |
| 8 | OUT3 | output | Constant-current output channel 3, rated for up to 120 mA output current and 20 V output voltage. |
| 9 | OUT4 | output | Constant-current output channel 4, rated for up to 120 mA output current and 20 V output voltage. |
| 10 | OUT5 | output | Constant-current output channel 5, rated for up to 120 mA output current and 20 V output voltage. |
| 11 | OUT6 | output | Constant-current output channel 6, rated for up to 120 mA output current and 20 V output voltage. |
| 12 | OUT7 | output | Constant-current output channel 7, rated for up to 120 mA output current and 20 V output voltage. |
| 13 | OE(ED2) | input | Output enable: when active (low) the output drivers are enabled and when high all outputs are blanked, also serving as a control input for Error Detection Mode and Current Adjust Mode, with an internal pullup. |
| 14 | SDO | output | Serial-data output to the following SDI of the next driver IC or to the microcontroller. |
| 15 | R-EXT | input | Connect an external resistor to ground to set the output current for all channels. |
| 16 | VDD | power_in | Supply voltage, recommended operating range 3 V to 5.5 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-16 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | 0 | | 7 | V | | 4 |
| Input voltage | VI | -0.4 | | | V | max VDD + 0.4 V | 4 |
| Output voltage | VO | -0.5 | | 20 | V | | 4 |
| Clock frequency | fclk | | | 25 | MHz | | 4 |
| Output current | IOUT | | | 120 | mA | | 4 |
| GND terminal current | IGND | | | 960 | mA | | 4 |
| Operating free-air temperature | TA | -40 | | 125 | °C | | 4 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature | Tstg | -55 | | 150 | °C | | 4 |
| Supply voltage | VDD | 3 | | 5.5 | V | | 4 |
| Supply voltage to output pins OUT0-OUT7 | VO | | | 20 | V | | 4 |
| Output current | IO | 3 | | | mA | VO >= 0.6 V, DC test circuit | 4 |
| Output current | IO | | | 120 | mA | VO >= 1 V, DC test circuit | 4 |
| High-level output current source | IOH | -1 | | | mA | SDO shorted to GND | 4 |
| Low-level output current sink | IOL | | | 1 | mA | SDO shorted to VCC | 4 |
| High-level input voltage | VIH | 0.7 | | | × VDD | CLK, OE(ED2), LE(ED1), and SDI | 4 |
| Low-level input voltage | VIL | 0 | | 0.3 | × VDD | CLK, OE(ED2), LE(ED1), and SDI | 4 |
| Junction-to-ambient thermal resistance | RθJA | | 51.8 | | °C/W | N package (PDIP-16) | 4 |
| Output leakage current | Ileak | | | 0.5 | μA | VDD = 3 V, VOH = 17 V, TJ = 25°C | 5 |
| Output leakage current | Ileak | | | 2 | μA | VDD = 3 V, VOH = 17 V, TJ = 125°C | 5 |
| Low-level output voltage | VOL | | | 0.4 | V | VDD = 3 V, SDO, IOH = 1 mA | 5 |
| Output current 1 | IO(1) | 1 | | 26 | mA | VDD = 3 V, VOUT = 0.6 V, Rext = 720 Ω, CG = 0.992 | 5 |
| Output current error, die-die | IO(1) | -6 | | 6 | % | VDD = 3 V, IOL = 26 mA, VO = 0.6 V, Rext = 720 Ω, TJ = 25°C | 5 |
| Output current skew, channel-to-channel | IO(1) | -3 | | 3 | % | VDD = 3 V, IOL = 26 mA, VO = 0.6 V, Rext = 720 Ω, TJ = 25°C | 5 |
| Output current 2 | IO(2) | | 52 | | mA | VDD = 3 V, VO = 0.8 V, Rext = 360 Ω, CG = 0.992 | 5 |
| Overtemperature shutdown | Tsd | 150 | 175 | 200 | °C | VDD = 3 V | 5 |
| Restart temperature hysteresis | Thys | | 15 | | °C | VDD = 3 V | 5 |
| Trigger threshold voltage for short-error detection | VOUT,TTh | 2.5 | 2.7 | 3.1 | V | VDD = 3 V, IOUT,target = 3 mA to 120 mA, TLC5917 only | 5 |
| Return threshold voltage for short-error detection | VOUT,RTh | | 2.2 | | V | VDD = 3 V, IOUT,target = 3 mA to 120 mA, TLC5917 only | 5 |
| Supply current, Rext = Open | IDD | | 5 | 10 | mA | VDD = 3 V | 5 |
| Supply current, Rext = 720 Ω | IDD | | 8 | 14 | mA | VDD = 3 V | 5 |
| Supply current, Rext = 360 Ω | IDD | | 11 | 18 | mA | VDD = 3 V | 5 |
| Supply current, Rext = 180 Ω | IDD | | 16 | 22 | mA | VDD = 3 V | 5 |
| Output leakage current | Ileak | | | 0.5 | μA | VDD = 5.5 V, VOH = 17 V, TJ = 25°C | 6 |
| Output leakage current | Ileak | | | 2 | μA | VDD = 5.5 V, VOH = 17 V, TJ = 125°C | 6 |
| Low-level output voltage | VOL | | | 0.4 | V | VDD = 5.5 V, SDO, IOH = 1 mA | 6 |
| Output current 1 | IO(1) | 1 | | 26 | mA | VDD = 5.5 V, VOUT = 0.6 V, Rext = 720 Ω, CG = 0.992 | 6 |
| Output current error, die-die | IO(1) | -6 | | 6 | % | VDD = 5.5 V, IOL = 26 mA, VO = 0.6 V, Rext = 720 Ω, TJ = 25°C | 6 |
| Output current skew, channel-to-channel | IO(1) | -3 | | 3 | % | VDD = 5.5 V, IOL = 26 mA, VO = 0.6 V, Rext = 720 Ω, TJ = 25°C | 6 |
| Output current 2 | IO(2) | | 52 | | mA | VDD = 5.5 V, VO = 0.8 V, Rext = 360 Ω, CG = 0.992 | 6 |
| Overtemperature shutdown | Tsd | 150 | 175 | 200 | °C | VDD = 5.5 V | 6 |
| Restart temperature hysteresis | Thys | | 15 | | °C | VDD = 5.5 V | 6 |
| Trigger threshold voltage for short-error detection | VOUT,TTh | 2.5 | 2.7 | 3.1 | V | VDD = 5.5 V, IOUT,target = 3 mA to 120 mA, TLC5917 only | 6 |
| Return threshold voltage for short-error detection | VOUT,RTh | | 2.2 | | V | VDD = 5.5 V, IOUT,target = 3 mA to 120 mA, TLC5917 only | 6 |
| Supply current, Rext = Open | IDD | | 6 | 10 | mA | VDD = 5.5 V | 6 |
| Supply current, Rext = 720 Ω | IDD | | 11 | 14 | mA | VDD = 5.5 V | 6 |
| Supply current, Rext = 360 Ω | IDD | | 13 | 18 | mA | VDD = 5.5 V | 6 |
| Supply current, Rext = 180 Ω | IDD | | 19 | 24 | mA | VDD = 5.5 V | 6 |
## CAD (KiCad official)
- Symbol: `TLC5917IN`
- Footprint: `Package_DIP:DIP-16_W7.62mm`
- 3D model: PDIP-16 (KiCad packages3D, STEP)
- 3D model files: `tlc5917in-etched.step` / `tlc5917in-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tlc5917in.step` / `tlc5917in.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tlc5917.pdf) (40 pp, sha256 `f257e916f7b5d37b`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tlc5917in-datasheet.pdf)