component
TLC0832CP
Public Made by Adomby adom
Texas Instruments Analog To Digital Converters (ADC), PDIP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTLC0832CP
Texas Instruments · Analog To Digital Converters (ADC) · PDIP-8
TLC0832CP from Texas Instruments, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Active-low chip select: pulling CS low enables the logic and starts a conversion, CS must be held low for the complete conversion, and returning it high clears the internal registers and puts DO into high impedance (CS high pulse width at least 220 ns). |
| 2 | CH0 | input | Analog multiplexer input channel 0, usable as a single-ended input referenced to GND or as the positive or negative terminal of a differential pair, with common-mode input range of -0.05 V to VCC+0.05 V. |
| 3 | CH1 | input | Analog multiplexer input channel 1, usable as a single-ended input referenced to GND or as the negative or positive terminal of a differential pair, with common-mode input range of -0.05 V to VCC+0.05 V. |
| 4 | GND | power_in | Network ground terminal; all voltages except differential voltages are referenced to this pin. |
| 5 | DI | input | Serial data input that shifts the start bit and multiplexer address word in on CLK rising edges (data valid 350 ns setup and 90 ns hold before/after CLK↑), and is ignored during conversion so it can be tied to DO for single-wire bidirectional use. |
| 6 | DO | tri_state | Serial data output that leaves high impedance after the one-clock MUX settling period, sends MSB-first conversion data followed by LSB-first data, and returns to high impedance when CS goes high. |
| 7 | CLK | input | Serial clock input operating from 10 kHz to 600 kHz with a 40% to 60% duty cycle; outside that duty-cycle range the minimum high or low pulse width is 1 µs. |
| 8 | VCC/REF | power_in | Supply pin specified at 4.5 V to 5.5 V (5 V nominal) that also serves as the voltage reference, internally tied to VCC on the TLC0832. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-8 |
| Category | Data Acquisition |
| Pins | 8 |
CAD (KiCad official)
- Symbol:
TLC0832CP - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: PDIP-8 (KiCad packages3D, STEP)
- 3D model files:
tlc0832cp-etched.step/tlc0832cp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tlc0832cp.step/tlc0832cp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (21 pp, sha256
0af85a1e9ea62978, retrieved 2026-10-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).