component

TJA1042

Public Made by Adom

by adom

NXP high-speed CAN transceiver, SOIC-8. ISO 11898-2, up to 5 Mbps CAN FD, standby mode, VIO variant. Datasheet-verified.

componentinterfacecan-transceivercan-fdautomotivesoic-8nxp
Overview Files Discover Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity

3D Model

Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

PCB Footprint

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

Datasheet

Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Download PDF
Contents

README

markdown

TJA1042

NXP · CAN transceiver · SOIC-8

Physical-layer transceiver between a CAN or CAN FD controller and the bus, meeting ISO 11898-2 at data rates up to 5 Mbps. TXD and RXD face the controller, CANH and CANL the bus, and an STB pin selects normal or a low-power standby with bus-wakeup. The SPLIT pin stabilizes the bus common mode, and a VIO variant matches the logic side to 3.3 or 5 V controllers. Bus pins tolerate wide common-mode and high ESD for automotive wiring. A standard modern CAN FD transceiver.

Pinout

Pin Name Type Function
1 TXD input Transmit data input from the host controller. Internal pull-up to VIO (or VCC on non-VIO variants) drives the bus recessive when left floating. A TXD dominant time-out (t_to(dom)TXD) releases the bus if TXD is held LOW too long, which also sets the minimum bit rate of 40 kbit/s.
2 GND power_in Ground supply. On the HVSON8 package this pin is internally connected to the exposed center pad; the GND pin must be soldered to board ground and the pad is recommended for thermal/electrical performance.
3 VCC power_in Main transceiver supply voltage. Operating range 4.5 V to 5.5 V (absolute max -0.3 V to +7 V). Undervoltage detection (V_uvd(VCC) = 3.5-4.5 V) forces the device into Standby.
4 RXD output Receive data output; reads the digitized differential state of the CAN bus (LOW = dominant, HIGH = recessive). Also signals wake-up requests in Standby mode by going LOW after a valid filtered bus wake-up pattern.
5 SPLIT/VIO bidirectional Dual-function pin whose role depends on the ordering variant. On TJA1042T and TJA1042CT this is the SPLIT common-mode stabilization output that delivers 0.5*VCC in Normal mode (floating in Standby / VCC off) for splitting bus termination. On TJA1042T(K)/3 and TJA1042BT(K) this is the VIO supply input (2.8 V to 5.5 V) that sets the I/O level of TXD, RXD and STB and powers the low-power differential receiver for standalone bus wake-up.
6 CANL bidirectional LOW-level CAN bus line. Driven LOW (toward GND) in the dominant state and biased to ~0.5*VCC in recessive. High-voltage solid (-58 V to +58 V DC) and ±8 kV IEC 61000-4-2 ESD on the bus pin.
7 CANH bidirectional HIGH-level CAN bus line. Driven HIGH (toward VCC) in the dominant state and biased to ~0.5*VCC in recessive. High-voltage solid (-58 V to +58 V DC) and ±8 kV IEC 61000-4-2 ESD on the bus pin.
8 STB input Standby mode control input. LOW selects Normal mode (transmit/receive enabled); HIGH selects low-current Standby mode with bus wake-up via the low-power differential receiver. Internal pull-up to VIO (or VCC on non-VIO variants) defaults the device to Standby if left floating.

Key specifications

Parameter Value
Type High-speed CAN / CAN FD transceiver
Standard ISO 11898-2:2016
Data rate Up to 5 Mbps (CAN FD)
Supply 5 V (VIO option for 3.3/5 V logic)
Modes Normal / standby (STB)
Bus ESD +/-8 kV (HBM)
Package SOIC-8

Ordering variants

Same part, different packaging or reel option.

  • TJA1042T (SOIC-8, no VIO)
  • TJA1042T/3 (SOIC-8, with VIO)
  • TJA1042TK/3 (SOIC-8, HVSON)

CAD (KiCad official)

  • Symbol: Interface_CAN_LIN:TJA1042T (KiCad official)
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: tja1042-etched.step / tja1042-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tja1042.step / tja1042.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: NXP datasheet (27 pp, sha256 aac9491f00e59436, retrieved 2026-08-17, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF